0 item

TechnoGym Run Now Excite Serivce Manual

Public Channel / Manuals

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

70.

2.

4.

217.

1. R R U U N N N N O O W W E X C I T E + R EV . 4.1

38. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.26 Page intentionally left blank.

112. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.42 Page in tentionally left blank.

168. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.56 Page intentionally left blank.

218. 0SM00674AA - UK TECHNOGYM S.p.A. Via Calcinaro, 2861 47521 Cesena (FC) ITALIA Tel.: +39 - 0547 - 56047 Fax: +39 - 0547 - 650150 e - mail: [email protected]

69. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 5.5 Page intentionally left blank.

68. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 5.4 5.6. SPECIFICATIONS AND A NTENNA REQUIREMENTS All the information about the minimum requirements concerning the antenna signal are detai led in the proper manual “Electrical and antenna requirements” you can find and download into the Technogym Direct.

132. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.20 7.4.2. VISIO T OUCH S CREEN For the Touch Screen disassembly, refer to the Display Board disassembling procedure described at the paragraph : 7.2.2. “ VISIO 19” ”.

210. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 10.2 Page intentionally left blank.

118. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.6 To reassemble the antenna cables (X) and (Y), follow the routing shown below. The D issipater (Z) is only on the ATSC and ISDB - T version. Figure 7.2 - 10

131. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.19 The keyboard assembly procedure can only be carried out once, because disassembly damages the tracks and keys. When reassembling the keyboard, make sure that none of the keys are bent or remain pushed in. After reassembly the Display, check the proper functioning of new keyboard, as described at the paragraph : 6.1.2.1 “ Man. Keyboard Test ”.

3. The information contained in this manual is intended for QUALIFIED TECHNICIANS who have completed a specific TECHNOGYM training course and are authorized to perform machine start - up and adjustment procedures as well as extraordinary maintenance or repairs which require a thorough knowledge of the machine, its operation, its safety devices and working procedures. CAREFULLY READ THE INFORMATION CONTAINED IN THIS MANUAL BEFORE PERFORMING ANY MA INTENANCE PROCEDURES ON THE MACHINE DANGEROUS VOLTAGES PRESENT NOTE: The information contained in this document is subject to change without notice. Technogym does not guarantee this documentation in any way. Technogym shall not be held re sponsible for any errors contained in this manual and declines all liability for accidents or damages resulting from the supply, characteristics or use of this manual. This document contains proprietary information that is protected by copyright. All righ ts reserved. No part of this document may be photocopied, reproduced or translated into another language without the prior written consent of Technogym. The Technogym™ trademark is property of Technogym S.p.A. The RUN Now Excite + ™ trademark is property of Technogym S.p.A.

66. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 5.2 5.2. MOVING The equipment has two fixed front wheels. To move the equipment, lift it up slightly, as shown in the illustration, and push it forwards and backwards. It is recommended not to raise the equipment, so as not to damage the anterior guard Given the weight of the equipment, we recommend 2 person be involved in lifting it. ATTENTION: For moving it is recommended to grab the frame and not the lat eral guards. After every moving, check if the equipment is on flat, adjust the left foot, as indicated at the paragraph : 8.5. “ The machine is not flat ”.

49. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.11 3.10. JOYSTICK These joysticks are used to adjust the speed and the elevation during the exercise. Each time they are pressed, forward or backward, they send a signal to the CPU board to change the speed or the elevation according to the joystick used . 3.11. LIMIT SWITCH This is a N C micro switch which defines the zero - reference position for the elevation mechanism: the switch is positioned so that it is pressed by the machine during the reset procedure, thereby defining the reference position.

108. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.38 (2) Take care of the following diagram to correctly position the machines: Figure 6 - 1 The active area of the transmitter is wider on the lateral side (130cm) instead of the front or the back side (90cm). Take care of the following diagram: Figure 6 - 2

153. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.41 Figure 7 - 77 CAUTION: It is important to respect the orientation of the limit switch during the reassembly. T he fast on (1) has to be oriented toward the REAR SID E of the machine , and the faston (2) and (3) have to face the FRONT SIDE of the machine , as shown in the figure above . CAUTION: During the reassembly check the adjust of the limit micro switch, as detailed at paragraphs: 8.3. “ Adjusting the limit micro switch ”.

101. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.31 Check the SW and the grounding of the Receiver Board. The problem persists? Receiver Board defective. Replace. A YES NO Check the connecting cable between High Kit and Low Kit. Its OK? OK . 4 NO OK . YES 3

83. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.13 Repl ace the LCD Inver ter . Does the pr obl em per si st? NO Defecti ve LCD Inver ter YES Repl ace the LCD. Does the pr obl em persists? YES Repl ace the CPU Boar d A NO Defecti ve LCD Continued on following page...

104. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.34 Check the SW and the grounding of the Receiver Board. Problem persists? Place correctly. 3 YES NO Check the properly functining of the Receiver Board. Is proper placed? OK 4 NO NO YES A Receiver Board defective. Replace. YES Check if it works properly using a chest belt you are sure it's ok. The problem persists? Chest Belt defective.

89. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.19 6.10. THE DISPLAY SHOWS “P RESS A KEYS / TOUCH THE SCREEN” This error message can be caused by: • loss of communication between the lower and upper assemblies; • the user has pressed the emergency button; • defective emergency button: the micro switch is opened. To In order to reinstate normal operation, simply press any key. If communication between the upper and lower assemblies is not immediately re - established, the message will remain on the display while the machine continues trying for 30 seconds, after which the “THE EQUIPMENT IS BLOCKED” message will appear. The machine keeps count of the att empts to reinstate communication by incrementing the COM.FAULT parameter, which can be viewed using the procedure described in the relevant paragraph of the Service menu .

62. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 4.2 4.2. PC LINK FOR PROGRAMM ING The machine can be connected to a PC for programming by means of the RJ45 connector on the C - Safe board. The cable to use must be wired as follows: ATTENTION: for the numbering of the pins, on RJ45 connector, please refer to the diagram below: When programming the machine som etimes it is necessary to fit plug into the free RJ - 45 port on the back of the display, to avoid any type of interference during the operation. The wiring diagram of the RJ - 45 plug is as follows: Programming cable and plug can be ordered using the code R0002534A C .

162. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.50 Figur e 7 - 15 4. Find the correct point where the slots on the lower side of the footboard are matching with the head of the screws on the frame. S ee picture on the side. 5. Remove the footrest (c) . To reassemble the Footrest, carry out the above steps in reverse order.

99. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.29 6.16. THERE IS NO HEART RA TE SIGNAL 6.16.1. HR/HS RECEIVER (H AND S ENSOR ) All models. HUMAN BODY “CONTINUITY”: it’s well known that for somebody it’s very difficult, nearly impossible, to measure their HR using the hand sensors. This due to a lot of possible causes which could fake the “quality” of the contact between the human skin and the HS plates, as: hands on ly just washed or particularly dry, acidity of the skin and/or a particular body fat mass index. For these people it’s suggested to wear the chest belt transmitter. HS CORRECT USE: Grasp both the upper and lower plate avoiding clenching them too hardly. Avoid washing the hands using soaps that can dry the skin too much. The machine displays this error if the HR/HS Receiver does not work or is not powered by the CPU/ARM Board. Continued on following page...

54. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.16 3.14. TREAD BELT MOTOR DRI VE 3.14.1. M ECHANICS The tread belt is actuated by the motor through a linkage consisting of the motor pulley, the driving roller and the belt which connects them. In this way, a given belt motor speed corresponds to a predetermined linear tread belt speed. 3.14.2. C ONTROLS The control block diagram is as follows: CPU Board ALE Driver Motor Cut-out Vac with variable frequency RS-485 CN17 J5 J5 J13A To actuate the motor, the CPU board communicates with the driver via the RS - 485 serial link. Based on the commands received, the Driver drives the motor by applying a variable frequency sinusoidal voltage: the frequency determines the speed of rotation of the motor and hence the linear tread belt speed. During its movement, the driver continually checks the motor by monitoring its current draw as well. If any problems are detected (low voltage, overcurrent, SW or HW inverter, etc....) it hal ts the motor and sends an alarm signal to the CPU board, which displays a “THE EQUIPMENT IS BLOCKED” which may lead to different error codes stored by the driver.

45. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.7 3.3.6. A UDIO /V IDEO EXTERNAL DEVICE CONNECTOR BOARD The board is positioned on the rear of the display of the equipment and makes available some connectors for connecting Audio / Video source and the external display on the base - band of LCD. 3.3.7. H EADPHONE JACK The machine display has one jack for connecting headphones. The jack is connected on a stereo output of the CPU Board. 3.3.8. C - S AFE BOARD ( INTEGRATED ): It 'a function that allows the connection using an appropriate cable for connecting ot her devices, such as: external PC suitably, programmed to control the machine (speed, level of difficulty, etc ...) 3.3.9. S ERVICE USB PORT ( INTEGRATED ): It is used to connect USB keys for updates: High Kit, Low Kit, Digital TV Board, Dual TGS reader and the tran sfer of Radio and TV channels, from one VISIO device to another.

209. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 10.1 10. AGGIORNAMENTO DEL SW The procedure is activated by pressing the top right - hand corner, the bottom left - hand corner and the bottom right - hand corner of the screen in that sequence whe n the equipment is in Stand - By, as shown in the figure below . A new display will appear from which you can gain access to the various configuration menus, by entering the password on the number keyboard: In order to access the menu, enter the password 2502 and press the ENTER key in order to confirm, ESCI in order to quit. For the following menu, please refer to the relevant chapter in the VISIO manual.

86. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.16 6.5. THE TOUCH SCREEN DOE S NOT WORK / IT’S NO T CALIBRATED Only for VISIO models. For the following menu, please refer to the relevant chapter in the VISIO manual. 6.6. NO AUDIO SOUND Only for VISIO models. For the following menu, please refer to the relevant chapter in the V ISIO manual. 6.7. NO TV PICTURE Only for VISIO models. For the following menu, please refer to the relevant chapter in the VISIO manual. 6.8. THE RADIO DOES NOT P LAY Only for VISIO models. For t he following menu, please refer to the relevant chapter in the VISIO manual.

55. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.17 In addition, to protect the motor from overheating, each motor phase has a thermal cut - out connected in series. If the temperature exceeds the threshold value, the thermal cut - outs open and interrupt the circuit. The driver detects this condition as the opening of a NC external contact. In such a case the driver halts the motor and outputs an al arm signal to the CPU board which displays the “THE EQUIPMENT IS BLOCKED” message. 3.14.3. T HE SIGNALS INVOLVED • RS - 485 Signal This is a digital signal exchanged between the driver and the CPU board. • VAC Signal with variable frequency: This is the variable altern ating - voltage signal output by the driver (connector J5) to supply the motor. Increasing the frequency of this signal increases the motor speed. The frequency of the sinusoidal supply voltage sent by the driver to the motor can be viewed on the display usi ng the inverter manual test described at the paragraph: 6.2.2.2 “ Man. Inverter Test ”. • Cut - Out signal: Each motor phase is equipped with a normally - closed thermal cut - out which opens when the temperature exceeds a preset threshold. When this input signal is an open contact, the driver detects the alarm, halts the motor and sends an alarm signal over the RS - 485 line to the CPU board.

12. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 1.2 1.3. GENERAL RULES FOR RE PAIR PROCEDURES 1. Always mark any parts or positions which may be confused with each other at the time of reassembly. 2. Use original Technogym spare parts and lubricants of the recommended brands. 3. Use special tools where specified. 4. Consult the Technical Newsletters, which may contain more up - to - date information on adjusts and maintenance than those contained in this manual. 5. Before starting the repair procedu re, make sure that the recommended tools are available and in good condition. 6. For the procedures described in this manual, use only the specified tools. The tool sizes quoted in this manual are expressed in mm.

56. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.18 3.15. ELEVATION MOTOR DRIV E 3.15.1. M ECHANICS The machine incline is varied by moving a frame connected to the front wheels by means of the elevation motor rod. The motor movement is detected by a hall sensor which provides the motor motion control signal: each motor revolution generates a predetermined number of pulses and produces a known displacement of the rod and hence of the machine incline. The direction of rotation of the motor determines whether the machine moves up or down. 3.15.2. C ONTROL The control block diagram is as follows: CPU Board ALE Driver Motor Hall sensor RS-485 CN17 Pulses Limit switch Vdc J13A J7 J7 J8 To actuate the motor, the CPU Board communicates via the RS - 485 serial link with the ALE Drive. Depending on the commands received, the Drive sends a +24 or - 24Vdc power supply to the Up - Down motor, and in this way determines whether the actuator rod moves in our out. When the motor r eceives the voltage it begins to move.

201. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.27 9.5. SERVICE MENU CONFIG.: VISIO - VISIOWEB The procedure is activate d by pressing the top right - hand corner, the bottom left - hand corner and the bottom right - hand corner of the screen in that sequence, in Stand - By, as shown in the figure below: A new display will appear from which you can gain access to the various con figuration menus, by entering the password on the number keyboard: Enter the password 2501 and press the ENTER key to confirm or EXIT to quit. A menu will then appear which will provide access to the following sub - menus: For the following menu, pleas e refer to the relevant chapter in the VISIO manual.

211. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 11.1 11. SCHEDULED MAINTENANC E To keep the machine in perfect working order and forestall possible problems it is necessary to carry out the scheduled maintenance operations described below. The maintenance operations can essentially be classified according to the type of service and to who they need to b e performed: • ORDINARY maintenance operation : The ORDINARY maintenance operations can be performed by the club manager. They do not require any kind of technical knowledge, they only consist of simple external cleaning, for the purposes of general hygiene. • EXTRAORDINARY maintenance operation : The EXTRAORDINARY maintenance operations have to be performed by a TG qualified technician specially trained by Technogym. They consist of the set up, the start up, all the inspections and service operations and the a djustments the machine can need to guarantee a good state of wear and the proper functioning conditions.

142. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.30 7.12. DISASSEMBLING THE LO WER DASHBOARD GUARD Figure 7 - 56 Carry out the procedure described in paragraph : 7.11.1. “ Disassembling the upper dashboard guard ”. 1. Back off the 6 screws (a) using a 4mm hexagonal wrench . 2. Remove the lower dashboard guard . To reassemble the Lower Dashboard guard , carry out the above steps in reverse order .

166. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.54 7.22.4.2. B Typology Figure 7.22 - 22 1. Back off the 2 screws (1 ) that fixing the running deck at the frame , using a 10mm hexagonal wrench, locking down the nut on the opposite side using a 17mm wrench. 2. Remove the running deck and the belt. During the reassembly respect the sequence in dicated in the figure. CAUTION: During the reassembly lock down the screw (1) using a torque wrench settings on 30Nm.

109. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.39 (3) Check if the receiver has been correctly mounted on the machine, as detail at paragraph : 7.6. “ Disassembling the HS/HR cardio receiver (Chest Belt / Hand Sensor) ”. (4) To check for electromagnetic noise near the machine, use Test Box Excite as detailed here b elow. You can use one of the following cables ELT - 16 (0WC00518AB), CBQ - 28 (0WC00390AC) or TRM - 28 (0WC00336AC) as connection cable. TEST BOX EXCI TE RECEIVER LED Connecting cable The circuit lights the LED for each heart beat and/or disturbance received: in this way it is p ossible to determine whether there is any interference, and identify its sources. Do not keep the Test Box Excite too close to the display, to avoid the electric interference.

94. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.24 6.14. “GRADIENT NOT WORKIN G” MESSAGE ON THE DISPLAY If the elevation does not work and there is no error message on the display, the elevation movement may have been disabled in the configuration menu. For further details, refer to the relevant paragraph of the Service menu . Check parameter PAR 09 is set 15 (1,5 Sec.). This parameter defines the time window within which the inverter expects to receive a sufficient number of pulses from the elevation motor, before generating an error condition. 1. This error message indicates that the machine is unable to control the elevation motor. The error is produced when the inve rter does not receive any pulses from the motor encoder after having enabled it. After this, the machine continues to function with the elevation motor disabled and parameter PAR 07 set to 1. 2. The error message may be caused by a malfunction of the travel limit microswitch If the microswitch breaks during use, the machine will enable an upward elevation movement, in an attempt to open the microswitch contact. If the microswitch fails to open after a predefined number of pulses, the machine generates an elev ation error and halts the movement. 3. The error message may be caused by a misalignment of the "HALL" effect sensor, if it is not correctly aligned with its magnet. In fact, if the encoder of the elevation motor is not correctly positioned, the motor will f ail to output any pulses. At this point, the elevation movement will be disabled, and parameter PAR 07 set to 1. When the machine is switched on again, the parameter PAR 07 is automatically reset to 0 and the machine performs the reset procedure. If the e rror does not happen anymore, supposing it was generated by a noise, the machine restarts to work properly. It might also be helpful to refer to the theoretical explanation of the elevation control, provided in paragraph: 3.15. “ Elevation motor drive ”. Continued on following page.

200. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.26 9.4. CONFIG.: VISIO - VISIOWEB USER MENÙ The procedure is activated by pressing the top right - hand corner, the bottom left - hand corner and the bottom right - hand corner of the screen in that sequence, in Stand - By, as shown in the figure below: A new display will appear from which you can gain access to the various configuration menus, by entering the password on the number keyboard: Enter the password 2406 and press the ENTER key to confirm or EXIT to quit. A menu will then appear which will provide access to the following sub - menus: For the following menu, please refer to the relevant chapter in the VISIO manual.

82. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.12 6.4.2. VISIO M ODELS B Replace the CPU Board. Works? YES NO CPU Board def ectiv e A Does the wall outlet supply the correct v oltage? Is the power supply cable OK? Are the LED on the CPU board lit on? Plug the machine into a working electrical outlet Replace thecable THE DISPLAY STAYS OFF NO YES NO YES YES NO 1 Are the Circuit Bracker engage? Engage the Circuit Bracker YES NO Continued on following page...

96. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.26 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the c hecks highlighted by circled numbers, which are described in detail below: (1) Check the parameter setting as detailed in the relevant paragraph of the Service menu, is enabling. (2) Open the Driver cover plate and press manually the limit switch. When the limi t switch is pressed, DWN - SW has to be ON while has to be OFF if released. (3) Place the tester probes across pins 6 and 4 of connector J7 on Driver board. The measured value should be approximately 2.5Vdc. If an oscilloscope is available, it is possible to v iew the pulses produced by the encoder itself.

100. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.30 THERE I S NO HR SIGNAL (Hand Sendor) Check if t he + 5Vdc are at t he input of Receiver Board. Are t hem present ? ARM/ CPU Boar d def ect ive. Replace. 1 NO YE S Check if t he + 5Vdc are at t he out put of t he ARM/ CPU Board. Are t hem present ? Receiver Board def ect ive. Replace. 2 YE S NO NO YE S A Check if t he SW and t he gruonding of Receiver Board. T he problem persist ? 3 Replace t he connect oring cables bet ween t he High Kit and Low Kit . YE S Check if using a chest belt t hat you are sure it 's ok, it works properly. T he problem persist s? OK NO Continued on following page...

110. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.40 6.17.2. H AND S ENSOR HUMAN BODY “CONTINUITY”: it’s well known that for somebody it’s very difficult, nearly impossible, to measure their HR using the hand sensors. This due to a lot of possible causes which could fake the “quality” of the contact between the human skin and the HS plates, as: hands only just washed or particularly dry, aci dity of the skin and/or a particular body fat mass index. For these people it’s suggested to wear the chest belt transmitter. HS CORRECT USE: Grasp both the upper and lower plate avoiding clenching them too hardly. Avoid washing the hands using soaps tha t can dry the skin too much. NO Receiver Board defective. Replace. THE TELEMETRIC HR SIGNAL IS INCORRECT (Hand Sensor) Set the priority on the Hand Sensor. Problem solved? Check the state of wear of Hand Sensor cable. Problem solved ? OK OK NO 2 OK NO YES Check the Display SW versione and the grounding of the Receiver Board. 3 YES YES 1 NO

128. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.16 7.2.2.11. TGS + USB frontal plug Figur e 7 - 28 1. Back off the 2 screws (a) using a medium Phillips screwdriver . 2. Remove the TGS+USB group (b) from the f ront side . To reassembly the TGS and USB frontal plug , follows the above steps in the reverse order .

57. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.19 To control the elevation position, the Drive uses the following input signals: A travel limit micro switch which defines a zero - reference position, acquired by the machine during its power - on reset procedure and w henever the micro switch is pressed. The travel limit micro switch outputs a normally closed signal which becomes open when the micro switch is pressed. ATTENTION: when the travel limit micro switch outputs an open contact signa l (pressed, micro switch broken or cable interrupted), the downward movement of the machine is disabled. If the Drive detects problems with these signals during operation of the elevation motor, i.e.: If it has not received any pulses during a previously defined time interval. If, when the travel limit micro switch outputs an open contact signal, this contact does not switch to closed when the elevation motor moves upward by a distance of 2%. Then: The drive stops functioning with error code "EdC" The ma chine displays the "ELEVATION ERROR" message, and interrupts the exercise. The parameter Par 07 is switched to 1 to disable the elevation function. At this point the machine will only allow movements of the tread belt motor, but not of the elevation motor . To re - instate operation of the elevation motor, the machine must be turned off and on again, so as to automatically reset Par 07 to 0. If the problem persists, the machine will again show the elevation error on the Display. 3.15.3. R ESET PROCEDURE On power - up, t he machine performs a reset procedure in order to determine the zero - reference position for the elevation movements. The machine makes a downward movement until the travel limit micro switch is pressed, and then moves upward by the number of pulses (100 pu lses) defined in the elevation table to reach the reference "horizontal position". All the movements for reaching different elevations will be variations relative to this reference.

79. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.9 6.3. TROUBLESHOOTING MENU The procedure is activated by pressing the t op right - hand corner, the bottom left - hand corner and the bottom right - hand corner of the screen in that sequence when the equipment is in Stand - By, as shown in the figure below. A new display will appear from which you can gain access to the various c onfiguration menus, by entering the password on the number keyboard: Enter the password 2501 and press the ENTER key to confirm or EXIT to quit. By selecting the key which is highlighted in red, you will gain access to the TROUBLESHOOTING menu: For the following menu, please refer to the relevant chapter in the VISIO manual.

127. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.15 7.2.2.10. V entilation duct frontal plug F igure 7 - 26 1. Back off the 5 screws (a) using a medium Phillips screwdriver . Figur e 7 - 27 2. Remove the ventilation duct group (b ) . To reassembly the ventilation duct frontal plug , follows the above steps in the reverse order .

95. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.25 "GRADIENT NOT WORKING" MESSAGE ON THE DISPLAY Check the P09 parameter is correctly set 1 2 Replace the limit switch NO NO Set P09 = 0, turn of f and on the machine. The elev ation changes (elev ation enabled)? YES Is the limit switch working properly ? YES Check that during the mov ement, the pulse signals are present on the J7 connector of the Driv er. Replace the Driv er and set again the P09 = 15 NO Check if the tension reaches the elev ation motor during the reset procedure NO Replace the elev ation motor and set again the P09 = 15 YES Replace the Driv er and set the P09 = 15 NO 4

106. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.36 6.17. THE TELEMETRIC HEART RATE SIGNAL IS INCOR RECT 6.17.1. C HEST B ELT CORRECT USE OF THE CHEST BELT: Wear the chest belt take care the area of contact with the body is humid in order to guarantee it proper works. THE TELEMETRIC HR SIGNAL IS INCORRECT (Chest belt) Are the machines correctly spaced by the required minimum distance? Check the Receiver Board has been correctly mounted on the machine. Reposition the machines so they are adequately spaced Mount the Receiver Board in the right way NO YES NO Check the Display SW versione and the grounding of the receiver. 1 2 Chest belt defective NO NO YES A Check if it works properly using a chest belt you are sure it's ok. The problem persists? 3 YES Continued on follo wing page....

114. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.2 7.1.2. VISIO D ISPLAY Figur e 7 - 3 Turn off the machine and unplug the mains lead from the wall outlet. 1. Back off the 2 screws (a) using a 4mm hexagonal wrench . Figur e 7 - 4 2. Disconnect the connectors highlighted in the figure at the side . 3. Remove the Display . To reassembly the Display, follows the above steps in the reverse order.

61. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 4.1 4. ACCESSORIES 4.1. CARDIO THEATER CONNE CTION The machine can be connected to the Cardio Theater by means of the RJ45 connector on the C - Safe board. The Cardio Theater unit must be p rovided with a power cable having the following pin - out: RJ45 Connector Signal 5 +5Vdc 7 Ground ATTENTION: for the numbering of the pins, on RJ45 connector, please refer to the diagram below:

103. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.33 6.16.2. HR/HS R ECEIVER (C HEST B ELT ) All models. CORRECT USE OF THE CHEST BELT: Wear the chest belt take care the area of contact with the body is humid in order to guarantee it proper works. THERE IS NO HR SIGNAL (Chest Belt) Check if the +5Vdc are at the input of the Receiver Board. Are present? ARM/CPU Board defective. Replace. 1 NO YES Check if the +5Vdc are at the output of ARM/CPU Board. Are present? Receiver Board defective. Replace. 2 YES NO NO YES A Check the SW and the grounding of Receiver Board. Problem persist? 3 Replace the connecting cable between High Kit and Low Kit. YES Check if using the Hand Sensors the Heart Rate detected. OK NO Continued on following page...

135. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.23 7.7. DISASSEMBLING THE FA N Figure 7 - 40 Carry out the procedure described in p aragraph : 7.1. “ Disassembling the display ”. 1. Back off the 4 screws (a) using a 3mm hexagonal wrench . 2. Remove the fan guard . Figure 7 - 41 3. Remove the fan from its fixing housing . To reassemble the Fan, carry out the above steps in reverse order so .

143. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.31 7.13. DISASSEMBLING THE LA TERAL UPRIGHTS Figur e 7 - 57 Carry out the procedure described in paragraph : 7.9. “ Disassembling the lateral handlebar ”. 1. Back off the 2 screws (a) using a 8mm hexagonal wrench , on both side CAUTION: D uring the reassembly lock down the screws (a) using a torque wrench set for 30Nm 2. Remove completely the dashboard group from the equipment . Continued on following page...

159. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.47 Figure 7.21 - 10 1. Fix the Autotransformer at the frame using the 4 fixing screws, without locking down. 2. Push the Auto t ransformer completely forward in the direction of the yellow arrows, as shown in the figure above. 3. At the end, lock down, the 4 screws using a 5mm hexagonal wrench. Continued on following page...

197. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.23 9.3.8. L OW KIT MENU This function directly accesses the firmware of the inverter. To access this menu, when the LED display shows: LOW KIT MENU press ENTER . This fu nction is structured as follows: LOW KIT MENU Low Kit Version Config. Registers 9.3.8.1. Low kit version This function displays the inverter firmware version. To access this menu, when the LED display shows: LOW KIT VERSION press ENTER , the following message appears: H:x L:x B:x Which identifies the firmware version.

48. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.10 3.6. EMERGENCY BUTTON This is a safety device which allows the user to stop the machine in an emergency situation. It consist s of 2 magnetic sensors fixed to the machine display, which form a NC contact when the emergency stop device is correctly positioned on the control panel during exercise. If a user is in difficulty and press the emergency device from the control panel or p ull the emergency rope, the NC contact is opened then the CPU/ARM board shows the message: LED display: “PRESSA KEY” VISIO display: “TOUCH THE SCREEN” Moreover the CPU/ARM board sends a signal to the Drive which cuts off the power supply to the tread bel t motor, halting the machine. 3.7. C - SAFE BOARD This board makes available a communication port, on 1 externally accessible connector, which can be used for interfacing compatible C - Safe devices such as the Cardio Theater readers. This connector is situated on the back of the display. These connectors can also be interfaced, using a special cable, to an external PC for programming the FLASH EEPROM. 3.8. BELT MOTOR An asynchronous three - phase motor which, by means of a pulley and poly - v belt, turns the driving roller of the tread belt. Is equipped with a normally - closed thermal cutout which opens when the temperature exceeds a preset threshold, in order to safeguard the integrity of the motor. The thermal signal reaches the driver as a NC external input signal. When th is contact opens, the driver generates an alarm. It is equipped with a high inertia flywheel, to permit more gradual deceleration of the tread belt in the event of a power outage or emergency stop. ATTENTION: dangerous voltages are present at the motor and flywheel. Potenza motore vedi paragrafo: 2.5. “ Technical specification ”. 3.9. ELEVATION MOTOR This is a linear actuator equipped with 24 Vdc moto r, integral reduction gear and a rod that is pushed backward and forward by the motor. This rod acts upon a frame connected to the front wheels of the machine: when the rod moves so does the frame, thereby lowering raising the machine. The actuator has a b uilt - in Hall effect sensor which acts as an encoder, generating pulses when the motor moves. This furnishes a feedback signal on the motor movements, which is used for tracking the position of the rod and hence the elevation of the machine.

144. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.32 Figure 7 - 58 Carry out the procedure described in paragraph: 7.14.1. “ Disassembling the upper guard ”. 3. Back off the 4 screws (b) using a 8mm hexagonal wrench. Figure 7 - 59 4. Back off the 2 screws (c) using a 8mm hexagonal wrench. CAUTION: During the reassembly lock down th e screws (c) using a torque wrench set for 30Nm.

174. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 8.6 8.5. THE MACHI NE IS NOT FLAT This problem may be due to the positioning of the machines on a not flat surface. To level the machine, you may adjust the height of the levelling foot . Figure 8 - 4 For the levelling adjus tment, carry out the operation on the rear RIGHT foot, as shown in figure : 1. Screw or unscrew the foot (a) to bring the frame in a flat and stable position. 2. At adjustment made, lock down the nut (b) .

125. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.13 7.2.2.8. Dual TGS Reader + USB port (G) Figur e 7 - 22 1. Unplug the cables highlighted in the figure. 2. Back off the 2 screws (a) using a medium Phillips screwdriver . Figure 7 - 23 3. Remove the TGS group and the USB port , as shown in the figure at the side . To reassembly the Dual TGS Reader and the USB port, follows the abo ve steps in the reverse order .

141. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.29 7.11.3. D ISASSEMBLING THE J OYSTICK Figure 7 - 54 Carry out the procedure described in paragraph : 7.11.1. “ Disassembling the upper dashboard ”. 1. Back off the 4 screws (a ) using a 5mm hexagonal wrench . Figure 7 - 55 2. Unplug the 4 faston (b) . 3. Remove the Joystick group (c ) . To reassembl e the Joystick group, carry out the above steps in reverse order .

97. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.27 6.15. THE MACHINE DOES NOT READ THE TGS The machine displays this error if the TGS reader is not working properly, or if it is not supplied by the CPU/ARM Board. THE MACHINE DOES NOT READ THE TGS Is the vol tag e at the i nput to the TGS r eader cor r ect? Is the vol tag e at the output to the Di spl ay Boar d cor r ect? Repl ace cabl e CBQ- 32 and/or CU132 1 2 YES NO YES Repl ace the Di spl ay Boar d NO A Is the ser i al communi cati on l i nk between the Di spl ay Boar d and the TGS r eader OK? Repl ace the TGS r eader . Is the communi cati on l i nk between the Di spl ay Boar d and the TGS r eader OK? TGS r eader defecti ve 3 3 YES NO YES Repl ace the Di spl ay Boar d NO A Repl ace the Dual TGS r eader

126. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.14 7.2.2.9. iPod Docking Station (H) Figur e 7 - 24 1. Lift the Docking Station covering cap up and back off the screw (a) using a medium Phillips screwdriver. . Figure 7 - 25 2. Unplug the cable highlighted in the figure at the side and remove the iPod Docking Station (H) . To reassembly the iPod docking station, follows the above steps in the reverse order. .

11. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 1.1 1. GENERAL NOTICES 1.1. INTRODUCTION This document is reserved for Technogym Service technicians, and is intended to provide authorized personnel with the necessary information to correctly carry out repairs and maintenance. A thorough kno wledge of the technical information contained in this manual is essential for completing the professional training of the operator. In order to facilitate consultation, the paragraphs are accompanied by schematic drawings which illustrate the procedure be ing described. This manual contains notices and symbols which have a specific meanings: WARNING: non observance may result in accident or injury. ATTENTION: non observance may cause damage to the machine. Information about the operation in progress. Observation about the operation in progress. 1.2. RECOMMENDATIONS Technogym recommends the following steps for planning repair procedures: • Carefully evaluate the customer’s description of the machine malfunction and ask all t he necessary questions to clarify the symptoms of the problem. • Clearly diagnose the causes of the problem. This manual provides the fundamental theoretical basis, which must then be integrated by personal experience and attendance at the training courses periodically offered by Technogym. • Rationally plan the repair procedure so as to minimize the downtime necessary for procuring spare parts, preparing tools, etc. • Access the component to be repaired, avoiding any unnecessary operations. In this regard it will be useful to refer to the disassembling sequence described in this manual.

124. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.12 7.2.2.7. Headphone Jack (F) Figur e 7 - 21 1. Unplug the connector highlighted in the figure . 2. Back off the 2 screws (a) using a small Phillips screwdriver. 3. Remove the He adphone Jack (F). To reassembly the Headphone Jack, follows the above steps in the reverse order .

140. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.28 7.11.2. D ISASSEMBLING THE CEN TRAL HANDLEBAR Figure 7 - 53 Carry out the procedure described in paragraph : 7.11.1. “ Disassembling the upper dashboard ”. 1. Back off the 2 screws (a ) using a 6mm hexagonal wrench . 2. Remove the central handlebar (b) . CAUTION: During the reassembly lock down the screws (a) using a torque wrench set for 30Nm. To reassemble the Handleba r, carry out the above steps in reverse order .

47. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.9 3.5. CARDIO RECEIVER BOAR D 3.5.1. HR/HS (C HEST BELT /H AND S ENSOR ) The receiver reception area is approximately a circle with a 90cm radius. If there is electromagnetic noise produced by high voltage lines, radio transmitters, monitors, motors ecc... within this area, the receiver becomes saturated and no longer receives any signal. This board manages the signals received from the Telemetric Transmitter ( Chest Belt ) and from the Hand Sensors, used by the user when exercising. The Board receives the +5Vdc power supply, from the Display Board. The Receiver Board, communicate with the Display Board in a positive logic mode. When the Board is in stand - by, the signal is +5Vdc; as soon the Board receives a reliable source of heart rate signal change to 0Vdc and then, for each heartbeat detected , generates a pulse going back to +5Vdc. The Display Board, can recognize if the signal is generated by the Chest Belt transmitter ( wireless signal ) or by the Hand Sensor ( contact signal ) from the width of the signal. In particular: if the width signal is 30msec, comes from the Chest Belt ( wireless ); if the signal is 100msec comes from the Hand Sensor ( contact ).

93. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.23 6.13. TREAD BELT MOTOR IS JERKING The probable cause is a disconnected phase either at the Driver board output or on the motor; TREAD BELT MOTOR IS JERKING Are the tread belt motor windings resistance correct? NO 1 YES Replace the tread belt motor Replace the Driv er Check if the IPA409 parameter is correctly 2 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check parameter IPA409 as detailed in the table at the paragraph: 9.5.3. “ Inverter ”. (2) Disco nnect the cable from the motor and place a tester across its terminals U - V, U - W and V - W. The measured value of the resistance should be 1.9 Ohm.

163. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.51 7.22.2. D ISASSEMBLY THE DRIVE N ROLLER In order to carry out these operations, it is necessary to slacken the tread - belt ten sio n. If the belt ha s to be used again, follow the instructions given in paragraph: 8.1.2. “ Tensioning a USED tread belt ”. Figure 7 - 16 Carry out the procedure described in paragraph : 7.22.1. “ Disassembling the footrest ”. 1. Back off the 2 screws (a) , on the rear roller of the machine , using a 8mm hexagonal wrench . CAUTION : Loosen the screws acting by turns on both the sides of the machine so that the rear roller is always parallel to the front one and to avoid to damage the roller bearings . 2. Remove the roller . To reassemble the Driven Rol ler, carry out the above steps in reverse order.

160. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.48 Figure 7.21 - 11 To replace the cable - tie that fix the autotransformer cable, under the motor, is necessary proceed as follow: 1. Back off the 5 screw (a) with a 4mm hexagonal wrench . 2. Remove the lower guard (b) . Figure 7.21 - 12 3. Replace the cable - tie making sure the autotransformer at the frame , as shown in the figure at the side .

172. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 8.4 8.3. ADJUSTING THE LIMIT MICRO SWITCH Figure 8 - 2 1. Loosen the 2 screws (a) that fixing the limit switch stop plate . 2. Adjust the position of the plate (b) completely down , as indicated by the yellow arrows above . 3. Finally , lock down the 2 screws ( a) previously loosened . CAUTION: During the reassembly lock down the screws (a) using a torque wrench set for 14Nm.

21. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.9 2.9. WIRING DIAGRAMS The machine consists of 2 assemblies witch are connected together (Display and Driver); depending on the model these 2 parties accept the various configurations, described below. 2.9.1. K IT B ASSO 2.9.1.1. ALE MET CE Display LED ALE MET CE (200-240V) ALE MET CE (100-120V) Display VISIO ALE MET CE (200-240V) ALE MET CE (100-120V) CU378 CU139 2.9.1.2. AT - UL Display LED AT-UL (90-265V) CU133 Display VISIO CU379

161. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.49 7.22. DISASSEMBLING THE RU NNING DECK AND ITS COMPONENTS In order to carry out these operations, it is necessary to slacken the tread - belt tension. If the belt has to be used again, follow the instructions given in paragraph : 8.1.2. “ Tensioning a USED tread belt ”. 7.22.1. D ISAS SEMBLING THE FOOTRES T Figur e 7 - 13 1. Back off 2 screws ( a) using a 4mm hexagonal wrench on both side . 2. Remove the rear guard (b) . Figure 7 - 14 3. Remove the footb oard (c) by pulling it out back ward . Continued on following page...

189. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.15 TECHNICAL CONFIGURATION OPERATING DATA KEY READER VERS. LOW KIT PARAM. UPDOWN SETTINGS HIGH KIT VERSION MAINS VOLTAGE ( AT UL ) ERRORS LOG STANDARD SETTINGS BOOT VERSION LOW KIT MENU To scroll through the list of parameters, press the + or – effort level keys to display the next or the preceding item. To modify a parameter value, it is necessary to press the ENTER key: when the current parameter value starts to blink, press the CLEAR key to erase the current value and then use the number keys to enter the desired new value. Save the changes made by pressing the ENT ER key. To cancel the operation, press the CLEAR key for a few seconds. The various parameters are described below.

158. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.46 Figure 7.21 - 8 9. Back off the 2 screws (h) using a 5mm hexagonal wrench. For reasons of space, for the 2 (h) screws is recommended to use a ratchet wrench. Figure 7.21 - 9 10. Remove the autotransformer (i) wi th careful . ATTENZIONE: Prestare particolare attenzione durante la movimentazione dell’autotrasformatore, poiché essendo estremamente fragile, anche un piccolo urto potrebbe danneggiarlo. To reassemble the autotransformer, carr y out the above steps in reverse order; following the note reported above: Continued on following page...

203. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.29 9.5.2. R EGISTER A DDR . This button allows selecting a specific parameter of the inverter, which then can be read using the fu nction described below: “Read from low kit”. On the Display will appear a Numeric Keypad which allows entering and/or modifying the numerical value of the parameter. Press CLEAR to delete the old value and insert the ne w one, then press CONFIRM to save it. 9.5.2.1. Read from low kit This button allows reading from Low Kit the value of the parameter set previously and displayed in the display. 9.5.2.2. Register Value This button allows modifying the value of the parameters. Press the bu tton: On the Display will appear a Numeric Keypad which allows entering and/or modifying the numerical value of the parameter. Press CLEAR to delete the old value and insert the new one, then press CONFIRM to save it. After any changes to the parameter values, you need to save them in the low kit using the “Write to low kit” function. 9.5.2.3. Write to low kit. To write the values of the currently displayed parameters to the low kit, press the button: Allows writing on the ALE inverter register, in case you have changed the data.

58. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.20 3.15.4. T HE SIGNALS INVOLVED The machine uses the following control signals: • R S - 485 Signal This is a digital signal exchanged between the driver and the CPU board. • Motor voltage signal (Vdc) This is the DC voltage generated by the driver ( pins 2 and 1 of connector J7 ) for supplying the elevation motor. Its absolute value is 24Vdc a nd, depending on its polarity, it causes the motor to rotate in either a clockwise or anticlockwise direction. The incline of the machine will increase or decrease accordingly. • Pulse signal This is a square wave signal with frequency 50 Hz (T=20 msec) and 50% duty cycle generated by the Hall sensor when the elevation motor moves. This signal enters the driver ( pins 6 and 4 of connector J7 ) and provides the feedback of the motor movement. This signal alternates between a low value of 0Vdc and a high value of 5Vdc. When measured with a multimeter, this signal is at either 0 or 5Vdc when the motor is stopped, while during motor movements it is approximately 2.5Vdc. In order to function correctly, the Hall sensor requires a +5Vdc supply voltage which it recei ves from the elevation board ( pins 5 and 4 of connector J7 ). • Limit switch signal The limit switch is a NC contact entering the /AT UL driver ( pins 3 and 8 of connector J8 ), which opens when the machine pressed it during the power - on reset procedure.

98. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.28 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) In Place the tester probes across pins 1 and 3 of connector CN1 of the TGS reader. The measured val ue should be +12Vdc. (2) As for step (1) but across pins 1 and 8 of connector CN19 (CPU Board) or on the CN7 connector (ARM Board). (3) Use the serial communications test described at paragraph: 6.2.1.5 “ Seri al Ports Test ”. If you replace ARM/CPU Board, check that its SW version is updated, otherwise install the last version.

84. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.14 2 Check if there is tension output to the power supply box NO YES Check if there is tension output to the ON/OFF switch NO 3 B YES Replace the ON/OFF switch Check if the power supply is connected and prov ide the +12Vdc 4 Connect and/or replace the power supply Replace the power supply box NO YES Check if the ALE driv er prov ide the +12Vdc 6 Connect and/or replace the power supply YES ALE driv er def ectiv e NO ONLY 110Vac VERSION SI Is the 220Vac v oltage to the output of the Autotransf ormer? 5 Replace the autotransf ormer NO YES

65. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 5.1 5. INSTALLATION INSTRUC TIONS 5.1. SPECIFICATIONS AND R EQUIREMENTS For correct machine installation, make sure that: 1. The machine is installed on a level surface that is free of vibrations and has sufficient carrying capacity for the combined wei ght of the machine and user. 2. The place of installation is free of dust and sand. 3. The place of installation meets the operating temperature and humidity conditions specified in paragraph : 2.7. “ Ambient specifications ”. 4. The machine is not positioned close to sources of heat, sources of electromagnetic noise (television sets, electrical motors, antennas, high voltage lines, household appliances, etc...) or medical equipment . Each machine must have a dedicated supply line. 5. The socket outlet and other devices on the dedicated line should be appropriately sized for the required load 16A. 6. The socket outlets must be earthed. 7. No multiple connections are permitted on the earth and/o r the neutral cables. 8. The ratio between the length and cross section ratio of the cables must be sufficient to assure a maximum voltage drop of 4% of nominal value at full load at the socket outlet. 9. Position the mains lead of the machine where it will not be underfoot. 10. There is plenty of free space around each item of equipment and a free space of 2x1meter min front of the machine as shown in the picture: 11. To eliminate any interference with the cardio receiver, no transmitters should be placed from the d isplay, as indicated in Figure 6 - 1 .

75. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.5 6.2. TROUBLESHOOTING MENU : 700LED – 900LED MODELS This section can be used to test the operation of certain machine components (AC/DC Motors, LED display, keyboard, serial p orts, Low Kit). It is invoked, when the machine is in standby mode, simultaneously press the keys 369 for 700 models. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2501 which protects against un authorized access and press the “Enter” key to confirm. At this point there are two options available: 1 = Tech Config 2 = Troubleshooting Press numeric key 2 to access the menu for configuring technical parameters; the machine display will begin showing the current configuration, structured as in the diagram below: TROUBLESHOOTING MANUAL TEST MAN.INVERTER TEST MAN.UPDOWN TEST MAN.KEYBOARD TEST I2C Devices Test AUTOMATIC TEST UpDown Test Inverter Test LED Test SERIAL PORTS TEST CSafe COM Test TGS COM Tes t Low Kit COM Test To scroll through the list of available functions, press the + or – speed keys to display the next or the preceding item; confirm the choice by pressing ENTER. To cancel the operation, press the CLEAR key for a few seconds.

193. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.19 9.3.4.3. Default setting To load the default parameter values to the display, scroll using the +/ - keys until the LED display shows: DEFAULT SETTING ? press ENTER to load the default parameter values, and return to the upper menu level by pressing CLEAR for a few seconds. To write these p arameters to the low kit, use the “Write to low kit” function. 9.3.5. O PERATING DATA This function makes it possible to access the machine usage data stored in the low kit. To access this menu, when the display shows: OPERATING DATA press ENTER . This function i s structured as follows: OPERATING DATA Life Kit H Life AC M WRITE TO LOW KIT ? READ FROM LOW KIT ? Life DC M Life Kit L Tot. Km In addition to the machine usage data, this function also includes the 2 sub - functions described below:

80. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.10 6.4. THE DISPLAY FAILS TO ILLUMINATE 6.4.1. LED M ODELS Does the main v oltage (110-220 Vac) is at the input of the machine and the circuit brakers are ok? Are the 2 LEDs on the rear side of the display board on? Bring the main v oltage to the inlet socket of the machine and/or check the circuit brakers THE DISPLAY FAILS TO ILLUMINATE NO YES NO YES 1 2 Are the 2 LEDs of +5 Vdc and +12Vdc, on the driver on? Replace the display board Replace the driver NO YES 3 5 Is the main voltage to the input of the driver? YES 4 Check the cables. NO ONLY 110Vac VERSION SI Is the 220Vac v oltage to the output of the Autotransf ormer? 6 Replace the autotransformer NO A YES Continued on following page...

152. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.40 7.19. DISASSEMBLING THE LI MIT SWITCH Figure 7 - 75 Turn off the machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph : 7.14. “ Disassembling the Lower Kit guard ”. 1. Unplug the connector highlighted in the figure, of the limit switch cable from the Driver box . Figur e 7 - 76 2. Press on both the sides of the limit switch and pull it out from the lower side of the guard . 3. Unplug the faston (a) if necessary . To reassemble the Limit Switch , carry out the above steps in reverse order . Continued on following page...

164. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.52 7.22.3. D ISASSEMBLING THE TRA NSMISSION BELT AND M OTOR ROLLER Figure 7 - 17 Carry out the procedure described in paragraph : “ Disassembling the upper guard ” and 7.22.1. “ Disassembling the footrest ”. 1. Release the belt tensioner spring (a ) . Figure 7 - 18 2. Remove the belt (b) from its pulley (c) and place it on the front roller . 3. Remove the motor roller (d) upwards . First on the right side and then axially on left . 4. Remove the transmission belt (b) if necessary . To reassemble the Motor Roller, ca rry out the above steps in reverse order.

157. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.45 Figure 7.21 - 5 7. Cut the cable - tie highlight in the figure at the side, paying attention to not damage the autotransformer cable. Figure 7.21 - 6 CAUTION: Incline the machine on the left side with caution and protecting it from the floor. To make safer the machine in this position, it is suggested to pla ce some weight on the handlebar closer on the floor. Figure 7.21 - 7 8. Back off the 3 screw (g) using a 5mm hexagonal wrench. Continued on following page...

198. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.24 9.3.8.2. Config. registers This function displays the parameter values of type b, C, D, F, P, H and S. To access this menu, when the LED display shows: CONFIG REGISTERS press ENTER , the following message appears: ADDRE SS: X where X is the address identifying anAT UL driver parameter, as detailed in the tables at the end of the paragraph. Press ENTER to change the address and select a different parameter, or press + to read the value of the currently selected parameter , the following message will appear: READ FROM LOW KIT ? press ENTER to load the parameter value, the following message will appear: VALUE: Y press ENTER to begin editing the parameter value. When finished, press + and the following message will appear : WRITE TO LOW KIT ? press ENTER to confirm writing the changes to the low kit; at the end of this operation the following message reappears: ADDRESS: X Although the changes made to the parameters come into effect immediately, they are not automatical ly stored in permanent memory; this requires a specific write operation effected using the command C - 0: at address 800 write the value “ 1” , following the detailed instructions provided in paragraph 9.3.8. 2 “ Config. registers ”. To return to the upper menu level press CLEAR for a few seconds. The inverter parameters are listed at paragraph: 9.5. 3. “ Inverter ”.

156. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.44 Figur e 7.21 - 2 4. Remove the dust - guard (e) . Figure 7.21 - 3 5. Remove the ferrite (f) from the motor cable and disconnect the other cables , highlight in the figure , from the autotransformer . Carry out the procedure d escribed in paragraph : 7.15. “ Disassembling the Lower Kit ”. Figure 7.21 - 4 6. Cut the cable - tie highlight in the figure at the side , paying attention to not damage the autotransformer cable . Continued on following page...

59. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.21 3.16. EME RGENCY STOP SIGNAL M ANAGEMENT The device consists of a button fitted below the display of the machine, which is composed by 2 NC micro switch connected in series. On the same button is connected a rope: if pulled act exactly as when you press the button. If a user is in difficulty and press the emergency device from the control panel or pull the emergency rope, the NC contact is opened then the CPU/ARM board realize about the emergency status. 3.16.1. C ONTROL LOGIC The control block diagram is as follows: Emergency CPU Board RS-485 CN2 2 Keyboard ALE Driver Reset Emergency Key Contact CN1 7 J3 A When the user press the emergency stop device, the NC contacts is opened, changing the state of the two signals output by them to the CPU. Each of the two micro switch outputs a distinct signal, interpreted as follows: one is an “ SW Emergency ” signal, and one is an “ HW Emergency ” signal. The two signals are managed as follows: SW Emergency: The CPU board detects the emergency condition and signals it by displaying the message “ Reposition the emergency stop device and touch the scree n ” and sends the information to the drive over the 485 serial link to halt the motors.. HW Emergency: The CPU board sends the emergency signal directly to the drive to halt the motors. To reinstate the machine's operation, it is necessary to reposition th e emergency stop device on the control panel and press any key on the display, as prompted.

115. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.3 7.2. DISASSEMBLING BOARDS AND COMPONENTS 7.2.1. LED D I SPLAY (ARM B OARD ) Figure 7 - 5 Carry out the procedure described in paragraph : 7.1.1. “ LED Display ”. Place the Display o n a work bench : 1. Disconnect the connector (a) . 2. Back off the 4 screws (b) usin g a medium Phillips screwdriver . 3. Remove the ARM Board . To reassembly the ARM Board, follows the above steps in the reverse order . After the reassembling of the Board, remem ber to fix the keyboard connector (a) using a drop of hot glue.

149. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.37 7.16. DISASSEMBLING THE P OWER S UPPLY BOX Figure 7 - 67 Turn off t he machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph: 7.14.1. “ Disassembling the upper guard ”. 1. Back off the 2 scr ews ( a) using a medium Phillips screwdriver . Figure 7 - 68 2. Remove the cover of power supply box (b) and unplug the faston if necessary . Figure 7 - 69 To com pletely remove the Power Supply Box : unplug the cable highlighted in the figure and back off the 3 screws (c), using a medium Phillips screwdriver . To reassemble the Power Supply Box, carry out the above steps in reverse order .

154. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.42 7.20. DISASSEMBLING THE EX TRA POWER SUPPLY Figure 7 - 78 Turn off the machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph: 7.14.1. “ Disassembling the upper guard ”. 1. Unplug the connector highlighted in the figure . 2. Cut the 2 cable tie (a) . 3. Remove the Power Supply (b) . I t’ s necessary to put the cable tie (a) again , during the reassembly . If you don’t have a new one do not cut it but remove using a small flat screwdriver to open the engaging tooth . To reassemble the Extra Power Suppl y, carry out the above steps in reverse order .

19. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.7 2.6.2. EUROPEAN AND OVERSEA S P ACKING DIMENSIONS 2.7. AMBIENT SPECIFICATIO NS Temperature Operating from 10° to 25° C Storage from - 10 to 70° C Humidity Operating from 20% to 90% non - condensing Storage from 20% to 90% non - condensing

87. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.17 6.9. THE IPOD DOES NOT WO RK Only for VISIO models. Is the iPod detected by the machine? YES SI THE iPOD DOES NOT WORK 1 Enter the audio/video files lists. Can you see the list of all the files uploaded on the iPod? Check the audio connection system NO Replace the Docking station board 2 3 YES Check the iPod cable connection. Is the iPod detected by the machine? OK YES Is the voltage at the input of the docking station correct? Replace the docking station board YES 5 NO 6 NO A Update the iPod SW version Has been the device enabled from the proper function in the user menu? Enable the iPod NO 4 7 NO Continued on following page....

113. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.1 7. PART DISASSEMBLY 7.1. DISASSEMBLING THE D ISPLAY 7.1.1. LED D ISPLAY Figur e 7 - 1 Turn off the machine and unplug the mains lead from the wall outlet. 1. Back off the 2 screws (a) using a 4mm hexa gonal wrench . Figur e 7 - 2 2. Open the Display , support it as indicated in the picture . 3. Disconnect the connectors highlight in the figure at the side . 4. Remove the Display . To reassembly the Display, follows the above steps in the reverse order .

51. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.13 3.12.2. ALE POWER SUPPLY BOX This is a box which contains:  The machine's power inlet socket.  The on - off switch.  2 resettable THERMAL CUTOUTS which monitor overloads on the phase and neutral.  An inductor  Filter Board This power supply box manages the power circuits of the machine: in particular, the input high voltage , which is then sent to the Drive, controlled through a second on - off switch. 3.12.3. S UPPLEMENTARY POWER S UPPLY This provides a supplementary +12V line required for operation of the VISIO, which in particular u ses it for powering the lights of the LCD. ATTENTION If the LCD lights fail to illuminate, one reason could be that this supplementary power supply is not supplied or is not working, and thus in its turn fails to supply the LCD. 3.13. AUTOTRANSFORMER Only for 110Vac version. It is a toroidal Autotransformer, placed on a plate fixed to the frame in the bottom of the machine under the running deck. The Autotransformer is connected in series to the power supply of the equipment and allo ws using the 110Vac power supply. It receives the 110Vac power supply and provides an output voltage of 220Vac for the Driver.

155. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.43 7.21. DISASSEMBLING THE AU TOTRANSFORMER (V. 11 0V) CAUTION: On machines produced WITHOUT autotransformer , not exist any upgrade kit and it is not possible to upgrade with Autotransformer for reasons of certif ication, standards and safety. The machines burn with Autotransformer with this typology from the production from Technogym ®. Figur e 7.21 - 1 Turn off the machine and unplug the mains lead from the wall out let. Carry out the procedure described in paragraph : 7.14.1. “ Disassembling the upper guard ”. 1. Cut the cable - tie that fixes the power cables and ground, as highlight in the figure at the side. 2. Remove the ferrite (a) and disconnect the male connector (b) and the female connector (c) of autotransformer . 3. Disconnect the ground cable (d) . Continued on following page...

187. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.13 9.2.16. U SER DETECT This function is able to de tect the presence of a user running on the tread belt during an exercise session. It is possible to configure a minimum speed at which the machine will determine that the user has stopped running on the treadmill, and interrupt the exercise session if the condition persists for one minute. To change the setting, when the LED matrix shows the current duration: USER DETECT: xxx Press the ENTER key to change the parameter: when the current parameter value starts to blink, press the CLEAR key to erase the cur rent value and then use the number keys to enter the desired new value. The default value of this parameter is 5.0 km/h The minimum threshold speed for the user detect function is 3.0 km/h. Entering any value lower than this will have the effect of disa bling the user - detect function. If the unit of measurement is setted to IMPERIAL units (miles / pound), the default value for this parameter is 3 mph while the minimum speed is 2 mph. At the end of the format procedure, hold down the CLEAR key for a few seconds to exit. The CLEAR key can be pressed at any time to interrupt the procedure and revert to standby mode. 9.2.17. S ERIAL N UMBER This parameter shows the serial number of the machine. SN:xxxx 9.2.18. I N M OTION – ( R EADY TO R UN ) It is possible to set how many time (in minutes) before the end of the exercise, the RED light on the handlebar, should starts blinking to indicate the soon end of the exercise. InMotion function is managed in minutes, with values ranging from 0 to 5. To change the setting, when the LED matrix shows the current time: I N M OTION ( MIN ): X Press the ENTER key to change the parameter: when the current parameter value starts to blink, press the CLEAR key to erase the current value and then use the number keys to enter the desired new value. The defa ult value of this parameter is 1. Setting “0” this parameter will have the effect of disabling the function.

60. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.22 The two micro switch connected in series, act for a double safety device because if one is damaged the others will stop the machine. ATTENTION: The message “ Reposition the emergency stop device and touch the screen ” appears on the display also if the serial communication between the high and low kit is interrupted. Pressing a key initiates the procedure for reinstating operation of the Drive, which receives a reset signal from the CPU board. After this, the Drive attempts to re - establish serial communications with the Display, and then repeats the reset procedure again. If serial communication cannot be established, the machine will ma ke a number of attempts. Each failed connection attempt is recorded in the COM FAULT parameter, which can be viewed as described in the relevant paragraph of the Service menu . After approximately 30 seconds, it stops and displays the error message “MACHINE BLOCKED (COM)”. 3.16.2. T HE SIGNALS INVOLVED The machine uses the following control signals: Emergency contact: This is the NC contact provided by the 2 micro switch actuated when the emergency stop button is pressed. This contact becomes open when the emergenc y stop device is detached. The signal enters the CPU Board through connector CN22 (pins 1 and 2) . RS - 485 Signal: This is a digital signal exchanged between the Drive and the CPU board. Emergency signal: This is the signal generated by the CPU board ( pins 1 and 4 of connector CN17 ) and sent to the Drive ( J3A) . This signal is 0Vdc under normal conditions, and goes to 11.9 Vdc in the emergency condition. Reset signal: This is the signal generated by the CPU board ( pins 1 and 10 of connector CN17 ) and sent t o the Drive (J3A) to signal to the low kit that normal operation has been reinstated after an emergency condition. This signal is 0Vdc under normal conditions and goes to approximately 8Vdc for a few seconds when the user presses a key. When this happens, the CPU Board resets the Emergency signal to 0 Vdc, thus allowing the Drive.

145. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.33 7.14. DISASSEMBLING THE LOWER KIT GUARD 7.14.1. D ISASSEMBLING THE U PPER G UARD Figure 7 - 60 Lift up the machine at the elevation of 10%, to make the procedure easier and turn off the machine . U nplug the mains lead from the wall outlet. 1. Loosen the 5 screws (a) using a 4mm hexagonal wrench. 2. Remove the upper guard (b) pulling it out from the front side of the machine . To reassemble the Upper Guard, carry out the above s teps in reverse order .

40. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.2 3.1.2. AT - UL D RIVER DISPLAY DISPLAY BOARD HS/HR RECEI VER HAND SENSOR (L) Capacitive TOUCH SCREEN HAND SENSOR (R) W I RELESS BOARD TUNER BOARD iPod Doking Station Dua l TGS Reader LCD Inve rte r "inMotion" BOARD Connectors Boa rd DRIVER BOX LIMIT SWITCH MOTOR ELEVATI ON MOTOR POWER SUPPLY BOX POW ER SUPPLY (VISIO only) DRIVER BOARD POWER BOARD J8 XPWR Fan 24VDC J3 J4 J5 J7 J2 J1 RESISTANCE XR1 XR2 JF XPWR XU2 XU2 XU1 XU1 Fan 24VDC XV1 Patch Conn. CU379 (VISIO) CU133 (LED) Up/Dow n JOYSTI CK SPEED JOYSTI CK

171. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 8.3 8.2. CENTRING THE TREAD B ELT Figure 8.2 - 1 1. Start the machine at a speed of 10km/h . 2. Observe the movement of the tread belt, correcting any tendency to shift to the right or left exclusively by adjusting the left tension screw ( a) 3. Locking down this screw favours shifting of the belt to the right a nd vice versa. The treadmill realigns slowly after some rotation: screw (or unscrew) the bolt ¼ or ½ a turn and then check the result before turning it again. 4. Gradually increase the speed to 16km/h, making any small adjustments that are necessary until the tread belt is perfectly centred.

182. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.8 9.2. USER MENU CONFIGURAT ION : 700/900 MODELS The machine configuration procedure is invoked, when the machine is in standby mod e, by simultaneously pressing the keys 369 , whereas on 700 Wellness TV models the keys 0369 must be pressed one after the other. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2406 and press ENT ER to confirm. At this point the machine display begins showing the current configuration, structured as in the diagram below: USER CONFIG Language MAX time Distance Pause time TGS Keys Custom Mess. Language Change Mess.Lang. Edit Mess. Default config. Format P&P User detect Up/Down HR SN Cooldown time Ready to Run

46. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.8 3.4. OPTIONAL 3.4.1. I P OD DOCKING STATION It is the device that allows to plug & store iPod models, in a safe docking station and to control it from the ACTIVE Wellness TV interface. With the docking station, developed for the full compatibility with iPod, it is possible to power, recharge and fully control it from the touch screen of the machine. In the following table, all the compatible iPo d(APPLE) models: iPod 5th gen. iPod Classic iPod mini iPod Nano iPod Touch iPhone 3.4.1.1. Client USB port This is an additional port which can be installed on the VISIO Display, and makes available a USB port for connec ting to external devices. The user can connect USB devices for playing a vast range of multimedia files, including: mp3, wma, wav, wmv, MPEG2, MPEG4, DivX, XVID jpg . 3.4.1.2. Dual TGS reader It’s the device which allows the machine to interact with the Wellness Sys tem. This board enables the machine to read the user's TGS key for performing workouts programmed with the proper SW of the Wellness System. With Dual TGS reader it is possible to use both the Botom and the Mifare TGS keys.

25. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.13 2.9.5. H IGH K IT 2.9.5.1. 500 model Display (ARM Board ) DISPLAY ARM Boa rd TRM-31 Keyboard C-Safe Boa rd CN1 CN1 CN2 CN7 CN9 CN10 Patch. Conn. B Patch. Conn. C HS/HR Riceiver HD4 HD3&2 HD1 CU244 Patch. Conn. Dua l TGS Reader CN3 CBQ-32 CU132 CN1 Patch. Conn. A CN6 Upper Sensor (Right) Upper Sensor (Left) Lower Sensor (Left) Lower Sensor (Right) CU136 LOWER KIT EMERGENCY Button MICRO MICRO CU377 NC C C NC CU242 o CU243 air duct micro CN12 CU307

195. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.21 9.3.6. E RRORS LOG This function accesses the machine’s error history log. To access this menu, when the display shows: ERRORS LOG press ENTER . This function is structured as follows: ERRORS LOG Error 10 Error 1 RESET ERRORS ? READ FROM LOW KIT ? ....................... COM.Fault In addition to the e rror history log, this function also includes the 2 sub - functions described below: 9.3.6.1. Read from low kit To read the errors stored in low kit memory and view them on the display, scroll using the +/ - keys until the display shows: READ FROM LOW KIT ? press EN TER to read the errors from the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.3.6.2. Reset Errors To clear the error history in both the low and high kit memory, scroll using the +/ - keys until the display shows: RESET ERRORS ? press ENTER to clear the error history logs, and return to the upper menu level by pressing CLEAR for a few seconds.

136. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.24 7.8. DISASSEMBLING THE HAND SENSOR Figure 7 - 42 Turn off the machine and unplu g the mains lead from the wall outlet. For each sensor : 1. Back off the 2 screws (a) using a small Phillips screwdriver. Figure 7 - 43 2. Remove the upper sensor (b) and the lower one (c) from the handlebar. U n plug the 2 faston (d) and (e) . 3. Remove the 2 sensors . During the reassembly: be careful to not press the cables with the two guides highlighted in the figure on the side. To reassemble the sensors, carry out the above steps in reverse order .

119. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.7 7.2.2.2. DVB - T Tuner Board (B ) Figure 7 - 11 1. Back off the 3 screws (a) using a medium Phillips screwdriver. 2. Remove the Tuner board protection guard (b) . Figure 7 - 12 3. Back off the 3 hex spacers (c) . 4. Lift up the black tab and disconnect the flat cable (d) . 5. Remove the Tuner Board (B) . To reassembly the Tuner Board, follows the above steps in the reverse order.

121. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.9 7.2.2.4. LCD Inverter (C) Figur e 7 - 15 1. Disconnect the connector highlighted i n the figure from the CPU . 2. Back off the 4 screws (a) using a medium Phillips screwdriver . 3. Remove the inverter guard (b) . Figur e 7 - 16 4. Unplug the 4 connectors highlighted in the figure . 5. Remove the Inverte r Board (C) . To reassembly the Inverter Board, follows the above steps in the reverse order .

173. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 8.5 8.4. ALIGNING THE TREAD - BELT MOTOR DRIVE - BELT Figure 8 - 3 Carry out the procedure described in paragraph : 7.14. 1. “ Disassembling the upper guard ”. 1. Remove the dust guard. 2. Release the spr ing ( a) of the belt tensioning mechanism. 3. Use a straight reference rod, resting it on the pulley (b) of the motor roller to align the belt (c) by shifting it within the races of the two pulleys. 4. At the end, reassembly the tension spring (a) .

122. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.10 7.2.2.5. CPU Board (D) Figur e 7 - 17 Carry out the procedure described in paragraph : 7.2.2.1 “ Wireless board (A) ” and 7.2.2.2 “ DVB - T Tuner Board (B) ”. 1. Disconnect the connectors highlighted in the fi gure . 2. Back off the 8 screws (a) using a medium Phillips screwdriver . 3. Remove the CPU Board (D) . To reassembly the CPU Board, follows the above steps in the reverse order .

63. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 4.3 4.3. MONITOR PLUG FOR C - SAFE PORT When the plug code 0WC00639AA is fitted into any one of the C - Safe ports on the machine, the corresponding LED should illuminate to indicate the presence of the 5Vdc supply on the port. During the C - Safe port tes t function, the plug connects the transmit channel directly to the receive channel, thereby producing a positive test outcome if the port is functioning correctly. 4.4. VISIOWEB UPGRADE 4.4.1. VISIO VS VISIOWEB The 2 product versions differ mainly for 2 reasons, on e it’s about its functionality while the second it’s about a technical characteristic... They are briefly detailed below: 1. On machines with VISIOWEB display it is possible for the user browsing and use internet services during the training session; 2. VISIOW EB has been developed on Linux instead of Windows CE used for VISIO . This difference can not be noticed by the final user because on both the product versions there is the same user interface and just few steps of the net configuration are different. 4.4.2. VISI OWEB UPGRADE FOR VISIO MODELS It is possible to upgrade equipment from VISIO to VISIOWEB through a specific SW upgrade procedure, using the proper USB recovery stick and a correct configuration for internet service (if the infrastructure has been properly arranged). The code to be used for this upgrade ATS600 CAUTION: this procedure must mandatory be done by a TECHNOGYM qualified engineer.

78. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.8 6.2.2.1. Man. Keyboard Test The manual keyboard test checks the functioning of all the keys on the keyboard. After accessing the test by pressing ENTER , the message “ Press all buttons (beep=OK) ” appears on the display. P ressing each key will produce an audible signal; if a key does not produce the beep it means it is not working properly. 6.2.2.2. Man. Inverter Test The manual inverter test displays the values output by the inverter drive during movements of the tread belt motor. The values displayed are: • Tread belt motor drive frequency (x100); • Current (x10); • Voltage. During the test it is possible to change the speed using the + and – speed keys, to see the change in the values of frequency, current and voltage. 6.2.2.3. Man. UpDown Te st The manual UpDown test displays the values output by the elevation motor drive during machine incline movements. The values displayed are: • Machine incline position; • Number of pulses generated by the elevation motor encoder; • State of limit switch: if it is pressed, “MIN” is shown, nothing in the other condition. During the test it is possible to vary the incline using the ↑ and ↓ elevation keys, to check that the values vary accordingly

192. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.18 9.3.4. U P D OWN SETTINGS This function allows access to the parameters in the UpDown table which define the number of encoder pulses that correspond to different machine incline positions. To access this menu, when the LED display shows: UPDOWN SETTINGS press ENTER . This functi on is structured as follows: UPDOWN SETTINGS +20%: -5.0%: WRITE TO LOW KIT ? DEFAULT SETTINGS ? READ FROM LOW KIT ? ....................... In addition to the 50 configuration parameters, this function also includes the 3 sub - functions described below: 9.3.4.1. Read from low kit To read the parameter values from the low kit memory to view them on the display, scroll usi ng the +/ - keys until the LED display shows READ FROM LOW KIT ? press ENTER to read the parameters from the low kit, then return to the upper menu level by pressing CLEAR for a few seconds. 9.3.4.2. Write to low kit To write the values of the currently displayed parameters to the low kit, scroll using the +/ - keys until the LED display shows: WRITE TO LOW KIT ? press ENTER to write the parameters to the low kit, and return to the upper menu level by pressing CLEAR for a few seconds.

146. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.34 7.14.2. D ISA S SEMBLING THE L OWER G UARD Figure 7 - 61 Turn off the machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph : 7.14.1. “ Disassembling the upper guard ”. 1. Unplug the micro connector and the Fan connector highlighted at the side from the Driver box . Figur e 7 - 62 2. To make the procedure easier, turn the machine over on one side. 3. Unplug the cables highlighted in the figure, using a 11mm wrench for the antenna cable . Figure 7 - 63 4. Back off the 5 screws (a) usi ng a 4mm hexagonal wrench. 5. Remove the lower guard. To reassemble the Lower Guard, carry out the above steps in reverse order .

123. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.11 7.2.2.6. LCD (E) + Touch Screen Figur e 7 - 18 Carry out the procedure described in paragraph : 7.2.2.4 “ LCD Inverter (C) ” e 7.2.2.5 “ CPU Board (D) ”. 1. Back off the 6 screws (b) using a medium Phillips screwdriver . 2. Remove the LCD group . Figur e 7 - 19 3. Carefully overturn the LCD group . 4. Back off the 2 screws (c) on both side s , u sing a medium Phillips screwdriver . 5. Remove the LCD (E) from its support plate . Figur e 7 - 20 6. C arefully remove the Touch Screen (d) and replace if it is necessary . To reassembly the LCD and Touch Screen, f ollows the above steps in the reverse order .

181. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.7 9.1.18. U SER D ETECT This function is able to detect the presence of a user running on the tread belt during an exercis e session. It is possible to configure a minimum speed at which the machine will determine that the user has stopped running on the treadmill, and interrupt the exercise session if the condition persists for one minute. To change the setting, when the LED matrix shows the current duration: USER DETECT: XXX Press the ENTER key to change the parameter: when the current parameter value starts to blink, press the CLEAR key to erase the current value and then use the number keys to enter the desired new value. The default value of this parameter is 5.0 km/h The minimum threshold speed for the user detect function is 3.0 km/h. Entering any value lower than this will have the effect of disabling the user - detect function. If the unit of measurement is setted to IMPERIAL units (miles / pound), the default value for this parameter is 3 mph while the minimum speed is 2 mph. At the end of the format procedure, hold down the CLEAR key for a few seconds to exit. The CLEAR key can be pressed at any time to interrupt the procedure and revert to standby mode. 9.1.19. S ERIAL N UMBER This parameter shows the serial number of the machine. SN: XXXXX 9.1.20. I N M OTION – ( R EADY TO R UN ) It is possible to set how many time (in minutes) before the end of the exercise, the RED light on the handleb ar, should starts blinking to indicate the soon end of the exercise. InMotion function is managed in minutes, with values ranging from 0 to 5. To change the setting, when the LED matrix shows the current time: I N M OTION ( MIN ): X Press the ENTER key to cha nge the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the nex t character. The default value of this parameter is 1. Setting “0” this parameter will have the effect of disabling the function.

190. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.16 9.3.3. L OW KIT PARAMETER This function provides access to parameters used for modifying certain settings of the lower assembly. To access this m enu, when the display shows: LOW KIT PARAM. press ENTER . This function is structured as follows: LOW KIT PARAM. Par.13 Par.01 WRITE TO LOW KIT ? DEFAULT SETTINGS ? READ FROM LOW KIT ? ....................... In addition to the 13 configuration parameters, this function also includes the 3 sub - functions described below: 9.3.3.1. Read from low kit To read the parameter values from the low kit memory and view them on the display, scroll using the +/ - keys until the display shows: READ FROM LOW KIT ? press ENTER to read the errors from the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.3.3.2. Write to low kit To write the values of the currently displayed parameters to the low kit, scroll using the +/ - keys until the display shows: WRITE TO LOW KIT ? press ENTER to write the parameters to the low kit, and return to t he upper menu level by pressing CLEAR for a few seconds.

120. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.8 7.2.2.3. Tuner board ATSC (B1 ) and ISDB - T (B2) Figure 7.2 - 13 Carry out the procedure described in paragraph: 7.2.2.2 “ DVB - T Tuner Board (B) ” at step (4) . 1. Remove the Tuner board ver. ATSC (B1) , or ver. ISDB - T (B2) . Figure 7.2 - 14 2. Back off the 2 screws (a) , using a medium Phillips Screwdriver. 3. Remove the dissipater (b) . To reassemble the Tuner Boards, follows the above steps in the reverse order.

129. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.17 7.3. AUDIO / VIDEO EXTERN AL CONNECTORS BOARD Figur e 7 - 29 1. Release the emergency cable (a) from its housing . 2. Back off the 2 screw s (b) using a medium Phillips screwdriver . 3. Remove the inspection plug (c) . Figure 7 - 30 4. Disconnect the connectors highlighted in the figure . 5. Back off the 2 screws (d) using a medium Phillips screwdriver . 6. Remove the Connectors Board (e). To reassembly the Connectors Board, follows the above steps in the reverse order .

139. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.27 7.11. DISASSEMBLING THE UP PER DASHBOARD GUARD , CENTRAL HANDLEBAR AN D THE J OYSTICK S 7.11.1. D ISASSEMBLING THE UPP ER DASHBOARD GUARD Figure 7 - 50 Carry out the procedure described in paragraph: 7.1. “ Disassembling the display ”. 1. Back off the 8 screws (a) using a mediu m Phillips screwdriver . Figure 7 - 51 2. Remove the Joystick plug (b) pressin g on both side s and using a small Flat screwdriver . 3. Back off the screw (c) using a medium Phillips screwdriver and remove the Joysti ck (d) . Figur e 7 - 52 4. Remove the upper dashboard (e) . During the reassembly : be careful to re - insert correctly the tabs (f), in the handlebar . To reassemble the upper dashboard, carry out the above steps in reverse order .

26. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.14 2.9.5.2. 700/900 LED Display (ARM Board ) LOWER KIT DISPLAY ARM Boa rd Up/Dow n JOYSTICK (Left) Speed JOYSTICK (Right) CN13 CN11 TRM-31 Keyboard C-Safe Reader CN1 CN1 CN2 CN7 CN9 CN10 Patch. Conn. B Patch. Conn. C HS/HR Riceiver HD4 HD3&2 HD1 CU244 Patch. Conn. Dua l TGS Reader CN3 CBQ-32 CU132 CN1 Patch. Conn. A CN6 Upper Sensor (Right) Upper Sensor (Left) CU136 TRM-29 TRM-29 Lower Sensor (Left) Lower Sensor (Right) CN23 Ready to Run Boa rd CU227 EMERGENCY Button MICRO MICRO NC C C NC CU377 air duct micro CN12 CU307 CU242 o CU243

170. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 8.2 8.1.2. T ENSIONING A USED TREAD BELT Figur e 8 - 3 1. Before slackening a used tread belt tha t needs to be re - tensioned, place a tape measure along the centre of the tread belt and use a pen to make two reference marks spaced exactly 1m apart. Figure 8 - 4 2. After reassembling the used tread belt, loc k down by turns the 2 screws ( a) until the distance between the two reference marks made previously on the tread belt are once again spaced 1m apart. Take care that the roller is always approximately parallel with the one on the front, to counteract the tension exerted by the belt on the roller bearings. This procedure is normally carried out after replacing the rear or driving roller, or in cases where a used tread belt needs to be reassembled. CAUTION: After completing this procedure, check the cent ring of the tread belt as instructed in paragraph : 8. 2. “ Centring the tread belt ”.

39. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.1 3. PRINCIPLES OF OPERAT ION 3.1. BLOCK DIAGRAMS WITH ALE DRIVER 3.1.1. ALE D RIVER (220V – 110V) DISPLAY DISPLAY BOARD HR/HS CARDIO RECEI VER HAND SENSOR (L) Capacitive TOUCH SCREEN HAND SENSOR (R) W I RELESS BOARD TUNER BOARD iPod Doking Station Connectors Boa rd Dual TGS reader LCD Inverter "inMotion" BOARD DRIVER BOX DRIVER BOARD J8 LIMIT SWITCH MOTOR ELEVATI ON MOTOR Fan (cover) POWER SUPPLY BOX J3A J4 J5 J7 J2 J1 RESISTANCE COVER XS1 Fan H.SINK XP1 CU378 (powered) POWER SUPPLY (VISIO Only) Patch Conn. 2 FE A (110V Only) FE CU378 (VISIO) CU139 (LED) SPEED JOYSTI CK Up/Dow n JOYSTI CK

151. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.39 7.18. DISASSEMBLING THE ELEVATION MOTOR Figur e 7 - 72 Turn off the machine and unplug the mains lead from the wall outlet. Carry out the pro cedure described in paragraph: 7.14.2. “ Disassembling the lower guard ”. 1. Unplug the elevation motor connector from the Driver . Figure 7 - 73 Turn the machine over on one side: 2. Remove the 2 split pins ( a) and remove the pin (b) that fix the elevation motor to the frame. 3. Remove the elevation motor (c) . To reassemble the Elevation Motor , carry out the above steps in reve rse order . Figur e 7 - 74 CAUTION: In case of elevation carriage disassembly, during the reassembly lock down the screws (d) using a torque wrench set for 9 0Nm ; and the carriage wheels fixing screws, highli ghted in the figure, using a torque wrench set for 40Nm.

74. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.4 6.1.1.4. LED Test The LED test checks the functioning of the display by lighting all t he LEDs in the matrix. It also tests the buzzer, varying the frequency to produce different tones of sound. The test does not produce a result message, so the user must visually check the outcome. 6.1.1.5. Serial Ports Test The serial ports test checks the followi ng communication ports: • C - Safe COM test; • Low Kit COM test; • TGS COM test. Using the + and – speed keys, select the desired test item and confirm by pressing ENTER . The test can have two outcomes: • “Test Successful, press Enter to continue”: This means tha t the test was completed successfully, i.e. that serial communications on the selected port are correct. • “COMx Error, press Enter to continue”: This means that the outcome of the test was negative: the message will specify COM1 in the case of the C - Safe CO M test, COM2 in the case of communications with the low kit, or COM3 in the case of the TGS COM test. The “TGS COM test” done on machine not provided with the key reader gives a fail outcome. The same if the “C - Safe COM test” is done on a machine which C - Safe port is not plugged with the monitor plug described at paragraph: 4.3. “ Monitor plug for C - Safe port ”. 6.1.2. M ANUAL T EST This section groups together tests for manually checking the operation of certain peripheral devices. After selecting the desired test item using the + and – speed keys, press ENTER to access the tests. To exit test mode, hold down the CLEAR key for a few seconds. The various manual tests are described below. 6.1.2.1. Man. Keyboard Test The manual keyboard test checks the functioning of all the keys on the keyboard. After accessing the test by pressing ENTER , the message “ Press all buttons (beep=OK) ” appears on the display. Pressing each key will produce an audi ble signal; if a key does not produce the “beep” it means it is not working properly.

138. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.26 7.10. DISASSEMBLING THE INMOTION – ( READY TO RUN ) BOARD Figure 7 - 47 Carry out the procedure described in paragraph: 7.9. “ Disassembling the lateral handlebar ”. 1. Press on the tabs (a) of the InMotion front guard (b) and remove it from t he handlebar . Figure 7 - 48 2. Back off the 2 screws (c) using a medium Phillips screwdriver. 3. Remove the light convector (d) . Figure 7 - 49 4. Unplug the connector (e) and remove the InMotion board (f) . To reassemble the InMotion Board , carry out the above steps in reverse order

137. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.25 7.9. DISASSEM BLING THE LATERAL HA NDLEBAR Figure 7 - 44 For each handlebar : 1. Back off the screw (a) using a 4mm hexagonal wrench . 2. Back off the 2 screws (b) using a 5mm hexagonal wrench . Figure 7 - 45 3. Back off the screw (c) using a 5mm hexagonal wrench . 4. Remove the guards (d) . Figur e 7 - 46 5. Back off the screw (e) and the 2 screws (f) using a 5mm hexagonal wrench . 6. Remove the u pper guard (g) if necessary . To reassembly the Handlebar, carry out the above steps in the reverse order . Continued on following page... →

184. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.10 9.2.5. C OOLDOWN TIME It is possible to set the cooldown time for each exercise, ranging from 5 to 180 seconds. To change the setting, when the display sho ws the currently selected maximum time: COOLDOWN TIME xxx Press the ENTER key to change the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current value and then use the number keys to en ter the desired new value. The default value of this parameter is 60. If you are exercising with a TGS key, the cooldown will be stopped if you extract the key. 9.2.6. E NABLE TGS It is possible to enable or disable the use of the TGS reader. To change the selec tion, when the display shows the current setting: TGS : xxx Press the +/ - GOAL keys to select the desired option out of those listed in the table below: TGS ENABLED <default> DISABLED 9.2.7. E NABLE KEYBOARD It is possible to disable the keyboard so that the machine can only be used with the TGS. To change the selection, when the display shows the current setting: KEYS : xxx Press the +/ - GOAL keys to select the desired option out of those listed in the table below: K EYS ENABLED <default> DISABLED

43. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.5 3.3.2. LCD INVERTER This device powers the LCD Display lamps. It receives DC power supplies (12 Vdc supply and 3.3Vdc enable signal) from the CPU Board, and generates the AC voltage (380 Vac) needed to power the LCD. 3.3.3. D IGITAL /A NALOGUE TUNER BOARD This is the board for receiving and managing the Audio/Video signal incoming from the antenna; it receives both digital and analogue signals. It is directly connected to the antenna cable, whose signal is then amplified, split between a video and audio channel, encoded by the decoder and processed by a tuner that permits searching and tuning of both TV and rad io channels. The data is then sent to the CPU Board where it is processed and managed in order to correctly display it on the LCD Display. LED name Colour Description D4 RED ON if the power supply reaches the board. OFF if the power supply does not reach the board. FLASHING :  if loading/starting the SW in the first seconds after it switch on;  During the firmware upload;  In case of HW/SW malfunctioning (and it continue to blink). 3.3.4. I NTEGRATED LAN NETWORK BOARD (W IRED ) The CPU board integrate a LAN network (L ocal Area Network) which can be used to connect the VISIO device in a local network. The connection should be realised through a UTP cable, with RJ45 connectors cat.5e/6. VISIO device is compatible with LAN networks, which have a max. transmission speed be tween 10 and 100 Mbps. The integrated network is obligatory in case of use for receiving IPTV stream

183. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.9 9.2.1. L ANGUAGE After selecting a language from the list of those available, all messages subsequently di splayed by the machine will be in the chosen language. To change the selection, when the LED matrix shows the current setting: LANGUAGE : xxx Press the +/ - GOAL keys to select the desired language from the options available. Press ENTER to confirm the ch oice, use the + or – speed keys to move to the next or previous parameter. 9.2.2. D ISTANCE It is possible to choose between EUROPEAN units (kg and km) or IMPERIAL units (pounds and miles). To change the selection, when the LED matrix shows the current setting: D ISTANCE : xxx Press the +/ - GOAL keys to select the desired unit of measurement from the options listed in the table below: D ISTANCE KM <default> MLS 9.2.3. M AXIMUM EXERCISE TIME It is possible to set a maximum duration for the exercise in minutes, with val ues ranging from 1 to 9999. To change the setting, when the LED matrix shows the current maximum time limit: MAX TIME: xxx Press the ENTER key to modify the parameter: when the current value of the parameter starts to blink, press the CLEAR key to erase the current value and then use the number keys to enter the desired value. The default value of this parameter is 9999. 9.2.4. P AUSE TIME It is possible to set a maximum duration of the pause for every exercise in seconds, with values ranging from 10 to 999. To change the setting, when the LED matrix shows the current maximum pause time: PAUSE TIME : xxx Press the ENTER key to change the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current val ue and then use the number keys to enter the desired new value. The default value of this parameter is 60.

71. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.1 6. TROUBLESHOOTING The troubleshooting procedures are illustrated by means of flow diagra ms. To facilitate interpretation of these diagrams, the following standard box shapes are used: START This type of box is the START point of the troubleshooting procedure. It typically contains a description of the problem or malfun ction. Decision This type of box represents a decision point in the troubleshooting procedure. It typically contains a description of the CHECK to be made, with an outcome that is either a positive (YES) or negative (NO) response. Action This type of box is a step in the troubleshooting procedure where an ACTION must be carried out. It typically contains a description of the ACTION necessary to resolve the problem Therefore, after executing the specified ACTION: 1. Check whether the problem has been resolved; 2. If the problem persists, it is recommended to resume the troubleshooting procedure from the point before the action was carried out. Note Clarification of the operation in progress or t hat will be below 1 A circled number (such as that shown on the left) next to a box of the troubleshooting procedure indicates that more detailed instructions for performing that particular check or action are provided below the flowchart. A A circled letter (such as that shown on the left) is used to mark a point in the procedure. Typically, this indicator is used in page changes. The connectors indicated in the foll owing pages, refer to 700 powered models Boards, unless otherwise indicated.

117. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.5 7.2.2.1. Wireless board (A) Figure 7.2 - 7 1. Unplug the 2 antenna connectors of the wireless board, hi ghlighted in the figure. CAUTION: Pay particular attention to the wireless antenna cables and connectors, because extremely sensitive, moreover in case of disassembly, it is important to follow the cable routing as shown in Figure 7.2 - 10 . Figure 7.2 - 8 2. Push simultaneously the 2 side tabs outward, in the direction of the purple arrows (1) . The Wireless Board will automatically lift up Figure 7.2 - 9 3. Remove the Wireless Board (A) in the direction of the orange arrow (2) , as shown in the figure at the side. CAUTION: During the reassembly, mount the antennas of Figure 7.2 - 7 on W ireless Board and after the Board in its housing; so not press on the CPU circuits. To reassemble the Wireless Board, follows the above steps in the reverse order.

169. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 8.1 8. ADJUSTMENTS 8.1. TENSIONING TH E TREAD BELT 8.1.1. T ENSIONING A NEW TREAD BELT Figur e 8 - 1 1. After replacing the tread belt, place a tape measure along the centre of the tread belt and use a pen to make two reference marks spaced exactly 1m apart. Do not measure the tread belt on the junction area, in order to keep the correct value. Figur e 8 - 2 2. Screw alternately the 2 screws (a) until the distance between the reference marks increases by 6mm . T ake care that the roller is always approximately parallel with the one on the front, to counteract the tension exerted by the belt on the roller bearings. CAUTION: After completing this procedure, check the centring of the tread belt as instructed in par agraph : 8.2. “ Centring the tread belt ”.

199. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.25 9.3.9. H IGH KIT VERSION This function displays the SW version of the display. To do this, when the LED display shows: HIGH KIT VERSION press ENTER , the message that identifies the SW version, will appear. 9.3.10. BOOT VERSION This function displays the BOOT version. To do this, when the display shows: BOOT VERSION press ENTER to display the message which identifies the BOOT version. 9.3.11. K EY R EADER V ERSION This function displays the SW version of the TGS reader. To do this, when the LED display shows: KEY READER VERS. press ENTER , the message that identifies the SW version, will appear. 9.3.12. M AINS VOLTAGE This function allows the user to choose the proper power supply voltage for the machine. To change the selection w hen the LED matrix shows the current setting: MAINS VOLTAGE: XXX Press the +/ - GOAL keys to select the desired voltage setting from the options available. Press ENTER to confirm the choice, use the + or – speed keys to move to the next or previous parame ter. The alternatives are: Mains Voltage NO SET 100 Vac 120 Vac 230 Vac Choosing “NO SET” value, when the machine is switched on it is necessary to insert the power supply voltage provided by the electrical mains line. Remember to properly set the parameter each time you replace the Display .

72. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.2 6.1. TROUBLESHOOTING MENU SERVICE: 500 LED MODELS This section can be used to test the operation of some machine components (AC/DC Motors, LED display, keyboard, serial ports, and inv erter). It is invoked, when the machine is in standby mode, by simultaneously pressing the keys ENTER , ↑ , CLEAR . The following prompt appears on the LED display: ENTER LA PASSWORD: To access the procedure, insert the password 2501 which protects against unauthorized access and press ENTER to confirm. To enter the password without the numeric keypad, enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. At this point there are two option s available: ↑ = Tech Config ↓ = Troubleshooting Press ↓ to access the troubleshooting menu, which is structured as shown in the figure below. TROUBLESHOOTING I2C Devices Test AUTOMATIC TEST MANUAL TEST UpDown Test Inverter Test LED Test SERIAL PORTS TEST MAN.KEYBOARD TEST CSafe COM Test TGS COM Tes t Low Kit COM Test To scroll through the list of available functions, press the + or – speed keys to display the next or the preceding item; confirm the choice by pressing ENTER. To cancel the operation, press the CLEAR key for a few seconds.

148. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.36 7.15.2. D ISASSEMBLING THE AT - UL D RIVER Figure 7 - 66 Turn off the machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph: 7.14.1. “ Disa ssembling the upper guard ”. 1. Disconnect the cables entering the Driver box : • Power Supply cable, • Cable connecting High Kit – Lower Kit, • Limit switch cable ; • Fan cable ; • Ground connection cable, • Tread belt motor cable, • Up - Down motor cable . 2. Back off the 4 s crews (a) using a medium Phillips Screwdriver . 5. Remove the Driver box . To reassemble the Lower Kit, carry out the above steps in reverse order .

77. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.7 6.2.1.3. Inverter Test The inverter test checks the condition of theAT UL driver. The test can have two outcomes: • “Test Successful, press Enter to continue”: This means that the test was completed successfully and the inverter is not in an error condition. • “Inverter Error, press Enter to continue”: This means that the test was not completed successfully, i.e. that the serial link is inactive and/or the inverter is in an error condition. 6.2.1.4. LED Test The LED test checks the function ing of the display by lighting all the LEDs in the matrix. It also tests the buzzer, varying the frequency to produce different tones of sound. The test does not produce a result message, so the user must visually check the outcome. 6.2.1.5. Serial Ports Test The serial ports test checks the following communication ports: • C - Safe COM test; • Low Kit COM test; • TGS COM test. Using the + and – speed keys, select the desired test item and confirm by pressing ENTER . The test can have two outcomes: • “Test Successful, pre ss Enter to continue”: This means that the test was completed successfully, i.e. that serial communications on the selected port are correct. • “COMx Error, press Enter to continue”: This means that the outcome of the test was negative: the message will spec ify COM1 in the case of the C - Safe COM test, COM2 in the case of communications with the low kit, or COM3 in the case of the TGS COM test. The “TGS COM test” done on machine not provided with the key reader gives a fail outcome. The same if the “C - Safe C OM test” is done on a machine which C - Safe port is not plugged with the monitor plug described at paragraph: 4.3. “ Monitor plug for C - Safe port ”. 6.2.2. M ANUAL T EST The tests g rouped under this section conduct checks on the machine’s operation in a fully automatic manner. After selecting the desired test using the + and – effort level keys, press ENTER to initiate the test and then await the result. To exit test mode, press and hold down the CLEAR key for a few seconds.

67. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 5.3 5.3. INSTALLATION To correctly install the machine, proceed as follows: 1. Ensure that the specifications and requirements for installation have been met, see paragraph: 5.1. “ Specifications a nd requirements ”. 1. Position the machine as specified above, on a level surface that is free of vibrations and has sufficient carrying capacity for the combined weight of the machine and user. 2. The machine is shipped partially assembled and packed in a carto n fixed to a wooden pallet. Follow the assembly procedure described in the “Operating and Service Instructions” supplied with each machine. Follow the assembly operations described in the instruction sheets supplied with the machines. 3. Connect the mains lea d to the power inlet socket on the machine. 4. Place the on/off switch in the “0” position. 2. Plug the mains lead into the wall outlet. 5.4. FIRST POWER - ON After completing the installation procedure, the machine is ready to be powered up. To turn on the machine, si mply toggle the on/off switch from the “0” position to the “1” position. During power - up the machine resets the incline. After completing the power - on reset, the machine goes into standby, awaiting a keyboard command. 5.5. TO CHECK THE CORRECT OPERATION OF THE MACHINE 1. Get on the machine; 2. Press the “Quick Start” key to begin exercising and check that the tread belt motor starts; 3. Press the “+” and “ - ” keys on the keyboard and check that the tread belt speed varies accordingly; 4. Press the “ ↑ ” and “ ↓ ” keys and check that the incline varies accordingly; 5. Press the emergency button and check that the tread belt stops; 6. Put on the heart rate meter and check that the machine correctly reads the heart rate value; 7. Grasp the sensors and check that the machine correctly reads the heart rate value 8. Check the properly operation of Speed Joystick and Up - Down Joystick ( only for 700 and 900 models ).

179. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.5 9.1.11. E NABLE TGS It is possible to enable or disable the use of the TGS reader. To change the selection, when the LED matrix shows the current setting: TGS: xxx Press the +/ - GOAL keys to select the desired option from those listed i n the table below: TGS ENABLED <default> DISABLED 9.1.12. E NABLE KEYBOARD It is possible to disable the keyboard so that the machine can only be used with the TGS. To change the setting, when the LED matrix shows the current one: KEYS: xxx Press the +/ - GOAL keys to select the desired option out of those listed in the table below: K EYS ENABLED <default> DISABLED 9.1.13. M ODIFIABLE TARGET HEA RT RATE It is possible to enable or disable modification of the target heart rate during a constant heart rate exercise. To change the selection, when the LED matrix shows the current value: HR: xxx Press the +/ - GOAL number keys to select the desired option out of those listed in the table below: HR MODIFIABLE <default> NOT MODIFIABLE

88. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.18 Is the v oltage at the output of the CPU Board correct? OK YES A 8 NO Replace the CPU Board Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Switch on the machine, connect the iPod on the docking station and check that the devic e is correctly detected by the machine. (2) Check that the audio/video files uploaded in the iPod are visible and selectable through the VISIO interface . (3) Carry out the troubleshooting procedure : 6.6. “ No audio sound ”. (4) To update the iPod SW you just need to connect to iTunes and it automatically upgrades to the last version. (5) Enable the iPod control as detailed in the relevant paragraph of the User menu . (6) The CU331 cable has identical connectors on either end then it can sometimes be connected the wrong way round . (7) Place the tester probes across pins 8 and 9 of the connector on the docking station board where the CU331 cable is connected. The measured value should be 5Vdc. (8) As for step (7) but across pins 6 and 7 of the connector on the CPU board where CU331 is connected . If you replace CPU Board, check that its SW version is updated, otherwise install the last version.

76. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.6 The tests are divided into two groups: Automatic and Manual , and the prompt for a choice appears immediately on accessing the troubleshooting menu. 6.2.1. A UTOMATIC T EST The tests grouped under th is section conduct checks on the machine’s operation in a fully automatic manner. After selecting the desired test using the + and – effort level keys, press ENTER to initiate the test and then await the result. Press ENTER again to continue, and use the C LEAR key to return to the higher menu level, holding it down for a few seconds. The various tests are described below. 6.2.1.1. I2C Devices Test The I2C Devices test checks the communication following the 32K and 256K. The test can have outcomes: • “Test Successful, press Enter to continue” : Signifies that the transmission and reception of data packets between the I2C devices and the display board was completed successfully. • “EEPROM Error, press Enter to continue” : Signifies that the display board is having problems communicating with its memories. 6.2.1.2. Up - Down Test The Up - Down test checks whether the number of pulses output by the encoder corresponds to the values of the Up - Down table stored in the low kit. During the test, the machine incline is moved from 0 to 15% ( for 700 models ) and from 0 to 18% ( for 900 models ) and then back to 0. Each incline position is converted into a number of pulses and compared with the value in the Up - Down table. Two messages appear during the test: • “ Incline =15%”: This message appears duri ng the upward movement, when the machine incline reaches 15%. • “Incline =3%”: This message appears during the downward movement, when the machine incline reaches 3%. The test can have two outcomes: • “DC Error (Up/Down), press Enter to continue”: The messag e indicates that the values do not correspond. The specific message (Up or Down) indicates whether the error occurred during the upward (Up) or downward (Down) movement of the test. • “Test Successful, press Enter to continue”: This message indicates that th e test was completed without errors.

134. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.22 7.6. DISASSEMBLING THE HS/HR CARDIO RECEIVER (CHEST BELT / HAND SENSOR) Figur e 7 - 37 1. Release the emergency cable (a) from its housing. 2. Back off the 2 screws (b) using a medium Phillips screwdriver. 3. Remove the inspection plug (c) . Figure 7 - 38 4. Remove the adhesive tape ( or the cable tie ) (d) and the nylon bag (e) . Figure 7 - 39 5. Remove the sponge (f) . 6. Unplug the connector and the fast - on , highlighted in the figure . To reassemble the HS/HR Receiver, carry out t he above steps in reverse order . CAUTION : During the reassembly: place the coil (g) , up wards oriented and toward the user. CAUTION : During the reassembly: fold the sponge on the Board: carefully and without pressing.

150. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.38 7.17. DISASSEMBLING THE BE LT M OTOR Figur e 7 - 70 Turn off the machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph: 7.14.1. “ Disassembling the upper guard ”. 1. Unplug the connector (a) of motor belt highlighted in the figure . Figure 7 - 71 2. Release the belt tensioner spring highlighted in the figure . 3. Back o ff the 4 screws (b) that fix the tread belt motor to the equipment frame , using a 17mm socket wrench . 4. Remove the support plate and the tread belt motor (c) . To reassemble the belt motor, carry out the above steps in reverse order . CAUTION: During the reassembly lock down the screws (b) u sing a torque wrench set for 15 Nm. CAUTION: At the end of the procedure, check the tension and alignment of the tread belt as detailed at paragraphs : 8.4. “ Aligning the tread - belt motor drive - belt ”.

196. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.22 9.3.6.3. COM.Fault This is a counter that display the number of errors in serial communication between the upper and the lower kit. This counter increase each time a communication fault is detected. Scroll using the +/ - keys until the display shows: COM.FAULT X To reset it press ENTER , the LED display shows: RESET COM.FAULT? press ENTER to reset and return to the upper menu level by pressing C LEAR for a few seconds. 9.3.6.4. View Errors For every error generated by the machine, the error history log records the information in the table below: • Error number; • Error code; • Tension at the error moment; • Current ( *10) when the error occurred • Speed at the error mo m ent Km/h. The correspondence between error codes and descriptions is given at paragraph : 6.1 2. “ driver errors ” of this manual. Use the + effort level key to advanc e to the next error, otherwise the message with the details of the current error will continue to reappear. 9.3.7. S TANDARD SETTINGS This function simultaneously resets the User menu, low kit, UpDown table parameters to their default values and the operating data of the machine. To access this menu, when the LED display shows: STANDARD SETTING press ENTER , the following message appears: CONFIRM ? Press ENTER again to reset all parameters to their default values, or return to the upper menu level by pressing CL EAR for a few seconds. This function does not alter the language and the TV standard setting.

216. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 12.2 12.2. REQUIRED T OOLS The following tools are req uired for carrying out the various disassembly, adjustment and maintenance action on the machine: • Small Phillips screwdriver; • Medium Phillips screwdriver; • Big Phillips screwdriver; • Small flat Phillips screwdriver; • 10mm wrench; • 13mm wrench; • 17mm socket wre nch; • 3mm Allen - T wrench; • 4mm Allen - T wrench; • 5mm Allen - T wrench; • 6mm Allen - T wrench; • 8mm Allen - T wrench; • Torque wrench. You can order a complete set of hexagonal wrenches consisting of 7 pieces: 2, 2.5, 3, 4, 5, 6 and 8 mm. The code to be used is R0003677AA. • Excite Test box (cod. H0003180AA - UK ).

175. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.1 9. MACHINE CONFIGURATIO N 9.1. USER MENU CONFIGURAT ION : 5 00 MODELS The machine configuration procedure is invoked by simultaneously pressing the keys ENTER , ↑ , CLEAR when the machine is in standby mode. The following prompt appears on the LED display: ENTER PASSWORD: To access the procedure, insert the passwor d 2406 and press ENTER to confirm. To enter the password without the numeric keypad, enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. At this point the machine display begins showin g the current configuration, structured as in the diagram below : USER MENU Language MAX time Distance Pause time Default age Default weight TGS Custom mess. Up/Down Keys HR User detect Default config. Default time SN Format P&P Default calories Default distance Cooldown Time Ready to Run Press ENTER to scroll the parameters saving the settings otherwise press the + or - SPEED keys to scroll the parameters without saving. Press CLEAR to cancel o r keep it pressed for few seconds to esc.

90. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.20 6.11. “THE EQUIPMENT IS LO CKED (COM)” MESSAGE ON DISPLAY In case of the machine stops with error “The equipment is locked” check the cause of the problem, reported between parentheses: (COM), related to serial communication errors; (EMER), related to emergency button errors; (cod. error), related to Low Kit errors. This error message can be caused by: • Loss of communication between the lower and upper assemblies; (COM) • The driver has detected an error condition, causing it to generate an alarm and store the error code in memory (cod. Error). • Problem on the emergency button (EMER) or (COM). To optimize the troubleshooting procedure, follow the steps below: 1. Access the item “ TROUBLESHOOTING  AUTOMATIC TEST  SERIAL PORTS TEST  Low Kit COM Test ”. If the outcome of the test is negative, check the components of the link between the upper and lower kit, in particular: • Check that the wiring of the various cables is not damaged, in particular the cables of the “emergency signal” and of the “reset” by referring to paragraph: 2.10. “ Cables ”; try replacing each of the circuit boards in turn (CPU/ARM board and driver box) and check whether the communication works. If the outcome of the test is OK move on to step 2. 2. Access the item check the error code stored in the “ E RRORS LOG ” and perform the corresponding troubleshooting procedure, if the outcome is OK advance to step 3. 3. The machine lockout problem has to do with the handling of the emergency signal: • Check that the emergency button is not pressed; • Check that the co rd, linked to the emergency button, is not to taut so that it keep the emergency button contact open; • Check that all the cables linked to the emergency device management are properly connected and in a good state of wear. WARNING: if the CPU/ARM board de tects an error condition during the tread belt motor movement, it displays the error message and turns off the AC motor by the driver.

73. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.3 The tests are divided into two groups: Automatic and Manual. The machine prompts for a choice immediately upon accessing the troubleshooting menu. 6.1.1. A UTOMATIC T ESTS The tests grouped under this section conduct checks on the machine’s operation in a fully automatic manner. After selecting the desired test using the + and – speed keys, press ENTER to initiate the test and then await the result. Press ENTER again to continue, or press the CLEAR key for a few seconds to return to the higher menu level. The various tests are described below. 6.1.1.1. I2C Device Test The I2C Device test checks the communication following the 32K an d 256K memories. The test can have two outcomes: • “Test Successful, press Enter to continue”: Signifies that data packets were successfully transmitted and received toward the display board. • “EEPROM Error, press Enter to continue” : Signifies that the displ ay board has communication problems with the memories. 6.1.1.2. UpDown Test The UpDown test checks whether the number of pulses output by the encoder corresponds to the values of the UpDown table stored in the low kit. During the test, the machine incline is moved from 0 to 15% and then back to 0. Each incline position is converted into a number of pulses and compared with the value in the UpDown table. Two messages appear during the test: • “Incline =15%”: This message appears during the upward movement, when the m achine incline reaches 15%. • “Incline =3%”: This message appears during the downward movement, when the machine incline reaches 3%. The test can have two outcomes: • “DC Error (Up/Down), press Enter to continue”: The message indicates that the values do not correspond. The specific message (Up or Down) indicates whether the error occurred during the upward (Up) or downward (Down) movement of the test. • “Test Successful, press Enter to continue”: This message indicates that the test was completed without error s. 6.1.1.3. Inverter Test The inverter test checks the condition of the AT driver. The test can have two outcomes: • “Test Successful, press Enter to continue”: This means that the test was completed successfully and the inverter is not in an error condition. • “Inver ter Error, press Enter to continue”: This means that the test was not completed successfully, i.e. that the serial link is inactive and/or the inverter is in an error condition.

214. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 11.4 11.2.8. C HECKING THE TREAD BE LT MOT OR DRIVE - BELT 1. Turn off the machine by placing the switch in position 0 (OFF). 2. Unplug the mains lead from the wall outlet. 3. Open the motor guard. 4. Check the state of wear of the tread belt motor drive - belt, turning it by hand using the motor flywheel. Replace if there are evident signs of wear. 11.2.9. C HECKING AND CENTERIN G THE TREAD BELT 1. With the machine stopped, check the tension over the entire surface of the tread belt, turning it by hand. If any anomalies are found, call in an authorized Technogym service techni cian. 2. With the machine moving at a speed of approximately 10 km/h, check the centring of the tread belt. Replace if there are evident signs of wear. 11.2.10. C HECKING THE WIRING A ND CONNECTIONS 1. Open all the machine guards. 2. Check the condition of all the cables: • Ex ternal conditions; • Possible rusting of the connectors; • Electrical continuity of the individual wires; • Isolation of the individual wires toward ground. 3. Repair and/or replace any non - conforming wires. Check the condition of the fuses using a tester. 11.2.11. C HECKIN G THE DISPLAY 1. Check the operation of all the keys on the keyboard. 2. Check the operation of all the LEDs and the buzzer. 3. Check VISIO Touch Screen calibration.

213. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 11.3 11.2. EXTRA - ORDINARY MAINTENANCE OPERATIO NS 11.2.1. C HECKING THE OPERATIO N OF THE CARDIOTESTE R RECEIVER 1. Using a separate heart rate monitor, put on the transmitter ban d and check that the machine and the separate monitor both measure the same heart rate, and that when the band is disconnected the machine does not receive any signal. 2. Using a heart rate frequency simulator, check that the machine detects variations in the heart rat. 11.2.2. C HECKING THE OPERATIO N OF THE HAND SENSOR RECEIVER 1. Using a separate heart rate monitor, grasp the hand sensors and check that the machine and the separate monitor both measure the same heart rate, and that when the sensors are released the mach ine does not receive any signal. 11.2.3. C HECKING THE WORKING CONDITIONS 1. Check that the machine is connected directly to the wall outlet, without any extension cords, and that the outlet is correctly earthed. 2. Using a multimeter, check that the machine earth node i s correctly connected to earth. 11.2.4. C HECKING THE STATE OF WEAR OF TREAD BELT A ND RUNNING DECK 1. Disassemble the rear and driving rollers, the running deck and the tread belt. 2. Check the state of wear of both the running deck and the tread belt. Replace if there a re evident signs of wear. 3. Using a clean cloth, wipe the entire surface of the running deck and the underside of the tread belt. 11.2.5. C HECKING THE WEAR OF THE MOTOR ROLLER 1. With the rear and driving rollers, running deck and tread belt disassembled, check the sta te of wear of the driving roller. Replace if there are evident signs of wear. 2. With the machine in motion, check the noisiness of the bearings. Replace in the event of excessive noise. 11.2.6. C HECKING THE STATE OF WEAR OF THE DRIVING ROLLER 1. With the front and rear rollers, running deck and tread belt disassembled, check the state of wear of the rear roller. Replace if there are evident signs of wear. 2. With the machine in motion, check the noisiness of the bearings. Replace in the event of excessive noise. 11.2.7. C HECKING T HE SHOCK ABSORBERS 1. With the front and rear rollers, running deck and tread belt disassembled, check the condition of the shock absorbers on either side of the running deck. Replace if they are cracked or show signs of breakage.

130. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.18 7.4. DISASSEMBLING THE KE YBOARD / TOUCH SCREEN 7.4.1. LED K EYBOARD Figure 7 - 31 Carry out the procedure described in paragraph : 7.1. “ Disassembling the display ”. Place the display assembly on a work bench : 1. Unplug the connector (a) . After t he reassembling of the board, remember to fix the keyboard connector using a drop of hot glue. 500LED Figure 7 - 32 700 LED and 900 LED Figur e 7 - 33 2. Use a shar p tool to lift up and detach a corner of the ke yboard then remove the keyboard. To assemble a new keyboard: 1. Remove the backing film which protects the adhesive. 2. Insert the connector in the special slot on the display and connect it to the ARM Board. 3. Apply the adhesive part, starting from the left and working toward the right, without bending the keyboard. 4. Remove the protective film. Continued on following page... →

85. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.15 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the LED 1 ( green ) of the CPU Board, is correctly lit on. (2) Check on the switch ON button’s faston, connected to the cable output to power supply box, if there is the 220 Vac voltage. (3) Check if the power supply voltages are at the output of the Power supply board and the continuity of the CU145 and CU318 cables by referring to paragraph: 2.10. “ Cables ” and replace what’s defective. (4) Check if there is the +12Vdc voltage at the input of the driver box on J1 connector. (5) Check if the 220Vac, are at the output of autotransformer, in direction of the Driver on J1 connector . (6) Check if there is th e +12Vdc voltage at the output of the driver box on pin 2 and 7 of CU378 cable (ALE driver) or CU379 cable (AT - UL driver) . If you replace CPU Board and/or Driver , check that its SW version is updated, otherwise install the last version. TV channels and RADIO, are only stored in a file in the fixed memory of the board. So the channels will be re - stored in case of replacing of the CPU Board.

188. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.14 9.3. SERVICE MENU CONFIGU RATION : LED MODEL S The configuration procedure is invoked when the machine is in standby mode, using a different procedure f or the 500, 700 or 900 models. 9.3.1. A CCESSING CONFIGURATI ON OF 500 MODELS Simultaneously press the ENTER , ↑ , CLEAR keys. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2501 which protects against una uthorized access and press “Enter” to confirm. To enter the password, increase or decrease the displayed value using the ↑ and ↓ keys, or use the +/ - GOAL keys to scroll through and modify the individual digits. At this point there are two options availabl e: ↑ = Tech Config ↓ = Troubleshooting Press numeric key ↑ to access the menu for configuring technical parameters; the machine display will begin showing the current configuration, structured as in the diagram below: 9.3.2. A CCESSING CONFIGURATI ON OF 700 AND 9 00 MODELS Simultaneously press the keys 369 for 700 models, whereas on 700 Wellness TV models the keys 0369 must be pressed one after the other. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 25 01 which protects against unauthorized access and press the “Enter” key to confirm. At this point there are two options available: 1 = Tech Config 2 = Troubleshooting Press numeric key 1 to access the menu for configuring technical parameters; the machin e display will begin showing the current configuration, structured as in the diagram below:

44. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.6 3.3.5. W IRELESS NETWORK BOAR D ( WITHOUT CABLES ) This is a board connected directly to the CPU, which enables the VISIO device to connect to a WLAN (wireless loc al area network) as an alternative to a wired network. The VISIO device has been constructed to be compatible with Wi - Fi technology (and in particular with the IEEE 802.11 b/g standard), which offers a theoretical bandwidth capacity of up to 54Mbps over distances d ependent on the characteristics of the setting where it is installed. The typical indoor range is 30 m (open space): • Standard: IEEE 802. 11b/g • Frequency band: 2.4GHz • Security protocol: WPA/WPA2 or also less recent ones (e.g. WEP ) . The WLAN connection m ay not guarantee the same performance as a wired network. The advantage of Wi - Fi is the absence of cables, but this is also a limitation in terms of protection against interference/disturbance, performance ( the stability of service and bandwidth may be int ermittent ) and security ( vulnerability to attacks by hackers) . Where possible, it is in any case preferable to use the wired network. The possibility of using Wi Fi also depends greatly on the type of service/application that is to be used in VISIO. In par ticular: • Technogym Communicator: usable with suitable Wi - Fi network • IPTV: NOT usable with Wi - Fi network; for this application, use of a wired network is essential . There are 2 different models of Wi - Fi network board used by Technogym, one produced by VI A and the other by Billionton . The 2 boards, are physically different as shown below: VIA model Billionton model Whenever you replace the board with another that is not the same model, you always have to carry out the “ System recovery ” procedure u sing the Recovery USB sticks.

147. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.35 7.15. DISASSEMBLING THE LO WER KIT 7.15.1. D ISASSEMBLING THE ALE D RIVER Figure 7 - 64 Turn o ff the machine and unplug the mains lead from the wall outlet. Carry out the procedure described in paragraph: 7.14.1. “ Disassembling the upper guard ”. 1. Remove the dus t protection (a) . 2. Back off the 4 screws (b) using a medium Phillips screwdriver . Figur e 7 - 65 3. Unplug the connectors highlighted in the figure : • Power Supply cable ; • Cable connecting High Kit – Lower Kit ; • Li mit switch cable ; • Fan cable ; • Ground connection cable ; • Tread belt motor cable ; • Up - Down motor cable . 4. Remove the Driver Box . To reassemble the Lower Kit, carry out the above steps in reverse order .

185. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.11 9.2.8. M O DIFIABLE TARGET HEAR T RATE It is possible to enable or disable modification of the target heart rate during a constant heart rate exercise. To change the selection, when the display shows the current setting: HR : xxx Press the +/ - GOAL number keys to se lect the desired option out of those listed in the table below: HR MODIFIABLE < default> NOT MODIFIABLE 9.2.9. E NABLE CUSTOM MESSAGE S It is possible to configure whether a custom message is displayed when the machine is in the standby state. To change the sele ction, when the LED matrix shows the current setting: CUSTOM MESS. : xxx Press the +/ - GOAL number keys to select the desired option out of those listed in the table below: CUSTOM MESS. YES <default> NO 9.2.10. E DIT MESSAGES It is possible to modify the cus tom messages; press ENTER to invoke a submenu which displays the first custom message, then use the +/ - speed keys to move to the other messages. Press the ENTER key again to begin editing a message, or hold down the CLEAR key for a few seconds to return t o the upper menu level. While editing a message, move the cursor using +/ - GOAL , select the desired letter using the +/ - speed keys and use CLEAR to enter a blank space character. Press ENTER to save the modified message, or hold down the CLEAR key to canc el and return to the upper menu level. 9.2.11. C HANGE MESSAGGES LANG UAGES It is also possible to display the custom standby messages in the language selected with the preceding parameter. To extend the language setting to the predefined custom standby messages, wh en the LED display is showing the current selection: CHANGE MESS. LANGUAGE

133. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.21 7.5. DISASSEMBLING THE EM ERGENCY BUTTON Figur e 7 - 34 1. Release the emergency cable (a) from its housing. 2. Back off the 2 screws (b) u sing a medium Phillips screwdriver . 3. Remove the inspection plug (c) . Figur e 7 - 35 4. Back off the 2 screws (d) using a medium Phillips screwdriver. 5. Back off the 2 screws (e) using a small Phillips screwdriver . 6. Remove the emergency button . Figure 7 - 36 7. Now i t’ s possible to act on the micro switch (f) o r on the faston (g) . During the reassembly , respect the cables routing , as shown in the figure . To reassembl e the Emergency Button, carry out the above steps in reverse order .

41. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.3 3.2. LED DISPLAY BOARDS 3.2.1. ARM B OARD : 500 AND 700 MODELS The display contains only one board which comprises the CPU, an ARM microprocessor, its logic circuits and a FL ASH EPROM containing the operating program for the machine moreover, acts as the interconnection hub for all the components of the display and serves as the point of connection with the low kit driver. The main functions of the board are: Manages and pro cess signals from:  Keyboard;  HR Receiver (500 LED);  HS/HR receiver (700 LED);  C - safe board;  Emergency button. Optional:  Dual TGS reader. Distributes the voltages received from the low kit driver; Exchanges, over the RS - 485 serial link to the driver bo x, commands for controlling the belt and elevation motors; Exchanges, over the RS - 485 serial link to the driver box, commands for controlling emergency signals; Controls the LEDs and the 7 - segment displays which provide feedback about the exercise session. The board includes the following indicator LEDs: LED mane Colour Description LED1 Yellow if ON the +12Vdc supply provided by the Driver box , correctly reaches the board. LED2 Green if ON the +5Vdc supply provided by the Driver box , correctly reaches t he board.

177. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.3 9.1.5. P A USE TIME It is possible to set a maximum duration of the pause for every exercise in seconds, with values ranging from 10 to 999. To change the setting, when the Display shows: PAUSE TIME: xxx Press the ENTER key to change the parameter: the current valu e of the parameter will start to blink, at this point press the CLEAR key to erase the current value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 60. In case you are exercising using a TGS key, the exercise is stopped if you remove the TGS key 9.1.6. D EFAULT AGE It is possible to set the default age for a generic user, with values ranging from 10 to 99. To change the setting, when the LE D matrix shows the current setting: DEFAULT AGE: xx Press the ENTER key to change the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 30. 9.1.7. D EFAULT WEIGHT It is possible to set the default weight of a generic user in KG, with values ranging from 10 to 999. To change the setting, when the LED matrix shows the current setting: DEFAULT WEIGHT: KG xx Press the ENTER key to change the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current value an d then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 70.

178. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.4 9.1.8. D EFAULT TIME It is possible to set the default duration of the exercise in minut es, with values ranging from 10 to 999. To change the setting, when the LED matrix shows the current time: DEFAULT TIME: MIN. xxx Press the ENTER key to change the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 15. 9.1.9. D EFAULT CALORIES It is possible to set th e calories for every exercise, with values ranging from 10 to 999. To change the setting, when the LED matrix shows the current setting: DEFAULT CALORIES: xxx Press the ENTER key to change the parameter: the current value of the parameter will start to b link, at this point press the CLEAR key to erase the current value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 300. 9.1.10. D EFAULT DIS TANCE It is possible to set the distance for every exercise in Km, with values ranging from 1 to 999. To change the setting, when the LED matrix shows the current setting: DEFAULT DISTANCE: KM xxx Press the ENTER key to change the parameter: the current value of the parameter will start to blink, at this point press the CLEAR key to erase the current value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 10.

194. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.20 9.3.5.1. Read from low kit To read the parameter values from the low kit memory and view them on the di splay, scroll using the +/ - keys until the display shows: READ FROM LOW KIT ? press ENTER to read the errors from the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.3.5.2. Write to low kit To write the values of the currently d isplayed parameters to the low kit, scroll using the +/ - keys until the display shows: WRITE TO LOW KIT ? press ENTER to write the new data to the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.3.5.3. Machine usage data The mac hine usage data on the display is updated every 10 minutes. This means that, whenever the machine is switched off, any data modified after the last memory update will be lost. MESSAGE ON DISPLAY DESCRIPTION Life AC M: Minutes x 10 of tread belt motor ope ration Life DC M: Minutes of elevation motor operation High Kit Life: Minutes x 10 of operation of the upper assembly Low Kit Life: Minutes x 10 of operation of the lower assembly Tot. Km: Total km travelled By selecting one of the items in the above table it is possible to modify its content, but only after having cleared its value. When the ENTER key is pressed the message "Reset life..." appears, followed by the name of the selected item; pressing ENTER again resets the value of the selected item, while pressing CLEAR reverts to the preceding value .

107. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.37 Are there sources of electromagnetic noise near the receiver? Receiver Board defective. Replace it. NO 4 The problem does not depend on the equipment YES A Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the correct display SW versi on, according to the “EXCITE SW SMART TABLE” you can find in TG Direct section. Check the grounding of the HR/HS Receiver Board , measuring the resistance value between: a. The ground fast on of HR/HS Receiver Board and the ground node on the Power supply box of the machine; b. The ground node on the Power supply box of the machine and the main wall socket. The measured value should be approximately lower than 1Ω (Ohm). Check finally the grounding of the main wall socket, measuring that the following voltages are present: P – N (phase – neutral) = 220Vac / 110 Vac P – G (phase – ground) = 220Vac / 110 Vac N – G (neutral – ground) = 0 Vac Continued on following page....

165. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.53 7.22.4. D ISASSEMBLING THE RUNNING DECK AND BELT In order to carry out these operations, it is necessary to slacken the tread - belt tension. If the belt has to be used again, follow the instructions given in paragraph: 8.1.2. “ Tensioning a USED tread belt ”. Figure 7 - 19 Carry out the procedure described in paragraph: 7.14.1. “ Disassembling the upper guard ” and 7.22.1. “ Disassembling the footrest ”. 1. Loosen the 2 screws (a) which fix the stopper s to the frame of the machine , using a 4mm hexagonal wrench . 7.22.4.1. A Typology Figur e 7 - 20 2. Back off the 2 screws (b ) which fix the running deck to the frame , using a 6mm hexagonal wrench . 3. Remove the running deck (c) . 4. Remove the belt (d) . CAUTION: During the reassembly lock down the screws using a torque wrench set for 30Nm. Figure 7 - 21 5. Remove the spacer (e) . During reassembly take c are to correctly insert the spacer (e) on the rear supports , as shown in the figure at the side. To reassemble the Running Deck and Belt, carry out the above steps in reverse order.

176. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.2 9.1.1. L ANGUAGE After selecting a language from the list of those available, all messages subsequently displayed by the machine will be in the chosen language. To change the selection, when the LED matrix shows the curre nt setting: LANGUAGE : xxx Press the +/ - GOAL keys to select the desired language from the options available. 9.1.2. D ISTANCE It is possible to choose between EUROPEAN units (Kg e Km) or IMPERIAL units (lbs e ml). To change the selection, when the LED matrix sh ows the current setting: DISTANCE: xxx Press the +/ - GOAL keys to select the desired unit of measurement from the options listed in the table below: D ISTANCE KM <default> MI 9.1.3. M AXIMUM EXERCISE TIME It is possible to set a maximum duration for the exer cise in minutes, with values ranging from 1 to 9999. To change the setting, when the Display shows: MAX TIME: xxx Press the ENTER key to modify the parameter: when the current value of the parameter starts to blink, press the CLEAR key to erase the curre nt value and then enter one digit at a time using the ↑ and ↓ keys to change the value and the +/ - GOAL keys to scroll to the next character. The default value of this parameter is 9999. 9.1.4. C OOLDOWN TIME It is possible to set the cooldown time for each exerc ise, ranging from 5 to 180 seconds. To change the setting, when the display shows the currently selected maximum time: COOLDOWN TIME xxx Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/ - GOAL keys to scroll through and modify the individual digits. The default value of this parameter is 60. If you are exercising with a TGS key, the cooldown will be stopped if you extract the key.

212. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 11.2 11.1. ORDINARY MAINTENANCE OPERATION 11.1.1. S ETTING UP THE OPERAT ION (D AILY ) 1. Turn off the machine by placing the switch in position 0 (OFF). 2. Unplug the mains lead from the wall outlet. 11.1.2. E XTERNAL CLEANING OPE RATIONS (D AILY ) 1. Using a cloth moistened with a neutral detergent (non acidic), clean the entire machine, taking care not to rub too vigorously, especially on the keys of the display. Never spray the cleaning product directly on the machine. WARNING: do not use alcohol, petrol or other chemical products. 11.1.3. I NTERNAL CLEANING OPE RATIONS ( M ONTHLY ) 1. Turn off the machine by placing the switch in position 0 (OFF). 2. Unplug the mains lead fro m the wall outlet. 3. Open the motor guard. 4. Use a vacuum cleaner to clean the interior, paying particular attention to the tread belt motor and the electronic circuit boards. ATTENTION: when carrying out these operations, be careful not to damage the cables . 5. Move the machine and clean the floor underneath using a vacuum cleaner. 11.1.4. C HECKING THE “E MERGENCY STOP ” (M ONTHLY ) 1. With the machine turned on and moving at a speed of approximately 5 km/h, trip the emergency stop and check that the machine halts, displaying the “PRESS A KEY” message 11.1.5. C OMPLETE OPERATION ( SIX - MENTHLY ) 1. To check that the switch, the tool maintains the reset procedure 2. To check the correct operation of the machine: • get on the machine; • press the Quick Start key to begin the exercise and check that the tread belt motor starts; • press the right Joystick and check that the tread belt speed varies accordingly; • press the left Joystick and check that the incline varies accordingly; • put on the heart rate meter and check that the machine correctly reads the heart rate value; • grasp the sensors and check that the machine correctly reads the heart rate value.

116. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.4 7.2.2. VISIO 19” D ISPLAY Figure 7 - 6 Carry out the procedure described in paragraph : 7.1.2. “ VISIO Display ”. Place the display on a work bench. It is now possible to remove the following components : • Wireless Board (A ) ; • TUNER Board (B) ; • LCD Inverter (C ) ; • CPU Board (D); • LCD + Touch Screen (E) ; • Headphone Jack (F) ; • Dual TGS Reader + USB port (G) ; • iPod Docking Station (H) ; • V entilation duct frontal plug ; • TGS + USB frontal plug .

27. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.15 2.9.5.3. 700/900 VIS I O Display (CPU Bo ard ) Antenna inlet Driver DISPLAY LCD CPU Boa rd Inverter CN1 Hadphone JACK J5 TOUCH SCREEN CN27 TUNER Boa rd W I RELESS Boa rd Antenna MAIN (B) Antenna AUX (A) J1 J2 J9 CN2 CN3 J6 JP10 Audio/Video connectors Board C-SAFE CN27 CN19 CN4 CN17 CN22 HS/HR Riceiver Lower Sensor (R) Lower Sensor (L) Upper Sensor (L) Upper Sensor (R) CU136 CN34 CN31 CN25 USB CBQ-32 CU132 Dua l TGS Reader USB CN14 iPOD DOCKING STATION CU331 CN26 CN40 J13 CU308 CU336 FLAT WB657 CU375 HD4 HD1 HD 3 & 2 CU337 CU376 CU244 CU333 FE CU387 CU381 CN4 Power Supply LAN EMERGENCY Button MICRO MICRO CU377 NC C C NC Ready to Run Boa rd CU348 CN6 CU246 Up/Dow n JOYSTI CK (Left) TRM-29 Speed JOYSTI CK (Right) TRM-29 CU378 o CU379 CN29 air duct micro CU307 CN33

180. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.6 9.1.14. E NABLE CUSTOM MESSAGE S It is possi ble to configure whether a custom message is displayed when the machine is in the standby state. To change the selection, when the LED matrix shows the current setting: CUSTOM MESS.: xxx Press the +/ - GOAL number keys to select the desired option out of those listed in the table below: CUSTOM MESS. YES <default> NO 9.1.15. E NABLE U P - D OWN MOTOR This parameter enables or disables use of the machine incline. To change the selection, when the LED matrix shows the current setting: UP - DOWN: xxx Press the +/ - GOAL number keys to select the desired option out of those listed in the table below: U P - D OWN ENABLED <default> DISABLED 9.1.16. R ESETTING PARAMETERS TO DEFAULT VALUES It is possible to reset the user menu parameters to their default values. To select the f unction, when the display shows: DEFAULT CONFIG. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. If the ENTER key is pressed the display will show: CONFIRM ? press ENTER to confirm, or cancel by pressing the CLEAR key for a few seconds. 9.1.17. F ORMAT P&P KEY This function formats a TGS key for Plug&Play mode operation. To select the function, when the display shows: FORMAT P&P Press ENTER to confirm. At the end of the formatting procedure, ho ld down the CLEAR key for a few seconds to exit. The CLEAR key can be pressed at any time to interrupt the procedure and revert to standby mode.

81. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.11 Is the main v oltage to the output of power supply box? YES Replace the cable of connecting between Driv er and Power supply box NO Replace the power supply box 7 A Follow the procedure step by step to correctl y diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: To speed up the troubleshooting procedure, check the state of the power indicator LEDs on the various circuit boards. (1) Slight ly lift the Fast - on connectors on the machine power inlet socket. Place the tester probes across the live and neutral pins on the same connector. The measured voltage should be approximately 220Vac/110Vac. (2) Check if LED 1 and 2 (+5Vdc and +12Vdc), on the A RM board are on. (3) Check if LED H6 and H3 +5Vdc and +12Vdc ( ALE driver ), or LED H2 and H3 ( AT UL driver ), are on. (4) Check if on connector J1, there is approximately 220Vac/110Vac, between pin 1 and 2 of the driver box. (5) Check the continuity of the power supp ly signals on the CU 242 cables between pin 1 and 5 (AT - UL driver) or on the CU 243 cables between pin 1 and 5 (ALE driver) , by referring to paragraph: 2.10. “ Cables ” and replace what’s defective. (6) Check if at the output to the Autotransformer there are the 220Vac, on the J1 connector. (7) Check if the main voltage 220Vac/110Vac is present and the continuity of the on the CU145 cable, pins 1 and 2 .

186. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.12 9.2.12. E NABLE U P - D OWN MOTOR This parameter enables or disables use of the machine incline. To change the selection, when the LED matrix shows the current setting: UP - DOWN: xxx Press th e +/ - GOAL keys to select the desired option out of those listed in the table below: U P - D OWN ENABLED <default> DISABLED 9.2.13. E NABLE MULTI - LANGUAGE MODE The machine can be configured to allow selection of the language at each session. To change the selection , when the LED matrix shows the current setting: LANGUAGE : xxx Press the +/ - GOAL number keys to select the desired option out of those listed in the table below: L ANGUAGE FIXED <default> OPTIONAL 9.2.14. R ESETTING PARAMETERS TO DEFAULT VALUES It is possib le to reset the user menu parameters to their default values. To select the function, when the LED matrix shows: DEFAULT CONFIG. Press ENTER to confirm the operation, use the + or – speed keys to move to the next or preceding parameter. If the ENTER key is pressed the LED matrix will show: CONFIRM ? press ENTER to confirm, or cancel by pressing the CLEAR key for a few seconds. 9.2.15. F ORMAT P&P This function formats a TGS key for Plug&Play mode operation. To select the function, when the LED matrix shows: FOR MAT P&P press ENTER to confirm. At the end of the format procedure, hold down the CLEAR key for a few seconds to exit. The CLEAR key can be pressed at any time to interrupt the procedure and revert to standby mode.

64. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 4.4 4.4.3. U P G RADE FROM LED TO V ISIO WEB There are upgrade kits available for converting Excite + machines from the version wit h traditional LED Display to the VISIO Display . The kit includes all components needed to install the kit and installation instructions. The table below gives the codes of the kits, to be chosen according to the TV standard used in the installation count ry: VISIO UPGRADE KIT Vers. 700 CODES Vers. 900 CODES RUN Now DVB - T A0000527 - D A0000528 - D RUN Now ATSC A0000527 - A A0000528 - A RUN Now ISDB - T A0000527 - I A0000528 - I Table 4 - 1 CAUTION: At the end of the U pgrade steps of Standard Setting , as described in the relevant paragraph of the Service menu . 4.5. ACCESSORISE ACCESSORISE CODE Dual TGS Reader15" A0000481 iPod Docking Station 15" A0000484 USB port 15" A0000485 Table 4 - 2

167. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 7.55 7.22.5. D ISASSEMBLING THE SHO CK ABSORBER Carry out the procedure described in paragraph: 7.22.4. “ Disassembling the running deck and belt ”. 7.22.5.1. A Typology Fig ure 7 - 23 1. Block the nut (a) using a 7mm wrench and back off the 2 screws (b) using a 3mm wrench . 2. Remove th e shock absorber (c) . To reassemble the Shock absorber , carry out the above steps in reverse order. CAUTION: During the re assembly lock down the screws (b ) using a torque wrench set for 3 Nm . CAUTION: At the end of the procedure, check the tension and alignment of the tread belt as detailed at paragraphs : 8.1. “ Tensioning the tread belt ” and in the paragraph : 8.2. “ Centring the tread belt ”. 7.22.5.2. B Typology Figure 7.22 - 24 1. Back off the 2 screws (n) using a 3mm hexagonal wrench, docking down the nut (q) on the opposite side. During the reas sembling follows the sequence indicated: • Screw (d), • Bush (c), • Plate (b), • Locking nut (a). To reassemble the various components, carry out the above steps in reverse order.

17. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.5 MODELS 500 LED 700 LED 700 VISIO 900 LED 900 VISIO Total number of program: 11 Quick Start, Goals (Tempo; Distance; Calorie), CPR, Profile (6) 23 Quick Start, Goals (Tempo; Distance; Calorie), CPR, Profile (6 defau lt, 9 custom), Custom, Training Zone, Weight Loss 23 Quick Start, Goals (Tempo; Distance; Calorie), CPR, Profile (6 default, 9 custom), Custom Speed, Training Zone, Weight Loss 23 Quick Start, Goals (Tempo; Distance; Calorie), CPR, Profile (6 default, 9 cu stom), Custom, Training Zone, Weight Loss 25 Quick Start, Goals (Tempo; Distance; Calorie), CPR, Profile (6 default, 9 custom), Custom Speed, Custom Pace, Interval, Training Zone, Weight Loss Sub - maximal test: Fitness test 3 Fitness Test, Single stage, Mu ltistage Maximal test: NO 8 Technogym Maximal Test, custom Maximal Test, Bruce, custom Bruce, Naughton, Balke e Ware, custom Astrand, Costill e Fox Military Test (US Army): NO 7 Gerkin Protocol, Air Force PRT, Navy PRT, Army PFT, Marine Corps PFT, Federa l Law Enforcement PEB Language available: 13 UK English, USA English, Italian, German, Spanish, French, Dutch, Portuguese, Japanese, Chinese, Russian, Turkish, Danish Plug & Play System: SI Wellness System: Optional

53. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.15 3.13.2. AT - UL DRIVER BOX It is the upper board of the assembly and it is the heart of the driver: it does everything was described above for the AT driver except the f unction of the AT power supply board described below. In details:  It receives the line voltage and, through a PFC module, it rectifies the voltage to the 400 Vdc used to generate the 3 phase voltage for the belt motor and to power up the AT power supply b oard.  Internally it houses an inverter to control the belt motor;  Internally it houses a DC driver to control the elevation motor. The board includes the following indicator LEDs visible when the AT driver cover is removed: LED name Colour Description A LARM ROSSO If ON indicates that the AT driver has detected an error (EdC) when it was moving the elevation motor. This LED stay ON for about 1 second and then goes OFF. EN_UP VERDE if ON indicates that the motor has received the supply voltage for movemen t in the upward direction EN_DOWN ROSSO if ON indicates that the motor has received the supply voltage for movement in the downward direction TACHO VERDE functioning of elevation motor encoder: if blinking, indicates that the board is receiving the pulse s from the encoder DWN_SW VERDE status of Limit switch contact: if ON indicates that the microswitch is pressed 3.13.3. AT - UL POWER SUPPLY BOARD It is the lower board of the assembly and it receives the 400 Vdc from the AT driver board and outputs to the AT driv er board the low voltages used by the machine. 3.13.4. F ANS There are 2 fans powered with 24 Vdc used to cool down the AT driver. 3.13.5. B REAKING RESISTOR It is a 150 Ohm used by the AT driver board to dissipate the energy produced by the motor when it is working as a ge nerator. 3.13.6. P OWER SUPPLY BOX It is a box that contains:  Power entry socket;  ON - OFF switch;  2 circuit breakers that check the overload on line and neutral;  A mutual inductance.

111. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.41 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the correct di splay SW version, according to the “EXCITE SW SMART TABLE” you can find in TG Direct , section. Check the grounding of the HR/HS Receiver Board , measuring the resistance value between: a. The ground fast on of HR/HS Receiver Board and the ground node on the Power supply box of the machine; b. The ground node on the Power entry module and the main wall socket. The measured value should be approximately lower than 1Ω (Ohm). Check finally the grounding of the main wall socket, measuring that the following voltages are present: P – N (phase – neutral) = 220Vac / 110 Vac P – G (phase – ground) = 220Vac / 110 Vac N – G (neutral – ground) = 0 Vac (2) Set the HR priority on the receiver board on “Hand Sensor”, by positioning the jumper ( JP1 ) on the receiver itself: JP1 CLOSED = Chest strap priority JP1 OPENED = Hand Sensor priority The standard configuration of the receiver is with chest strap priority. (3) Check that: c. The fast on of the cable are well connected to the HS plates; d. The continuity of the signal between the Hand Sensor plates and the relevant pin on HD3&2 connectors of the Receiver, referring to the paragr aph: 2.10. “ Cables ”; a. There is NO continuity between the HS plates and the ground fast on the receiver (otherwise the signals are grounded).

24. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.12 2.9.4. D RIVER : ALE MET CE 200 - 240V 2.9.4.1. ALE MET CE + LED SCATOLA AZIONAMENTO SCHEDA AZIONAMENTO J8 MICRO FINE CORSA MOTORE MOTORE PENDENZA Ventola (coperchio) POWER SUPPLY BOX INTER- RUTTORE ON/OFF C I R C U I T B R E A K E R VAC C I R C U I T B R E A K E R SCHEDA FILTRO J3A J4 J5 J7 J2 J1 RESISTENZA COVER XS1 Ventola PRESA DI ALIMENTA- ZI ONE CU143 CU143 IN2 IN1 4 1 L N CU143 5 2 CU177 FE CU145 OUT1 OUT2 DISPLAY (LED) H.SINK XP1 CU139 (alimentazione) CU144 CU156 C0605 (TRM-54) FE FE 2.9.4.2. ALE MET CE + VISIO SCATOLA AZIONAMENTO SCHEDA AZIONAMENTO J8 MICRO FINE CORSA MOTORE MOTORE PENDENZA Ventola (coperchio) POWER SUPPLY BOX INTER- RUTTORE ON/OFF C I R C U I T B R E A K E R VAC C I R C U I T B R E A K E R SCHEDA FILTRO J3A J4 J5 J7 J2 J1 RESISTENZA COVER XS1 Ventola PRESA DI ALIMENTA- ZI ONE CU143 CU143 IN2 IN1 4 1 L N CU143 5 2 CU177 FE OUT1 OUT2 DISPLAY (VISIO) H.SINK XP1 CU378 (alimentazione) CU144 CU156 ALIMENTATORE SUPPLEMENTARE C0605 (TRM-54) Conn. Volante 2 CU145 CU318 FE FE

15. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.3 2.2. SERIAL NUMBER STRUCT URE The Serial Number , consists of 14 alphanumeric characters arranged as follows : Characters Description Key to values 1,2,3,4,5,6, Product type, DAK = RUN Now Excite + 6 = 500 8 = 700 9 = 900 1 = 100 - 120V – MET CE 2 = 200 - 240V – MET CE E = 200 - 240V – CE U = 90 - 265V – AT - UL M = Medical Device - CE L = LED C = VISIO W = VisioWEB 7,8, Year of production, 10 = 2010 9,10,11,12,13,14. Progressive. 000001 For exampl e, a possible product code would be: DAK 8 1W10000001 2.3. COLOUR OPTIONS

22. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.10 2.9.2. D RI VER : AT - UL 100 - 120V 2.9.2.1. AT - UL + LED SCATOLA AZIONAMENTO SC HEDA A Z IONA M ENT O SC HEDA ALIMENTAZIONE J8 XPWR MICRO FINE CORSA M OTORE M OTORE PENDENZ A Ventola 24VDC J3 J4 J5 J7 J2 J1 RESISTENZA XR 1 XR 2 JF XPWR XU2 XU2 XU1 XU1 Ventola 24VDC XV1 CU010 CU011 C0605 (TRM-54) POW ER SUPPLY BOX INT ER- RUT T ORE ON/OFF C I R C U I T B R E A K E R VAC C I R C U I T B R E A K E R SC HEDA FILTRO PRESA DI ALIMENTA- Z IONE CU143 CU143 IN2 IN1 4 1 L N CU143 5 2 CU177 FE OUT1 OUT2 CU144 CU156 DISPLAY ( L ED) CU133 (alimentazione) CU145 2.9.2.2. AT - UL + VISIO SCATOLA AZIONAMENTO M ICRO FINE CORSA MOTORE MOTORE PENDENZA POWER SUPPLY BOX INTER- RUTTORE ON/OFF C I R C U I T B R E A K E R VAC C I R C U I T B R E A K E R SCHEDA FILTRO PRESA DI ALIMENTA- ZI ONE CU143 CU143 I N2 I N1 4 1 L N CU143 5 2 CU177 FE O UT 1 OUT2 DISPLAY (VISIO) CU144 ALIMENTATORE SUPPLEMENTARE SCHEDA AZI ONAM ENTO SCHEDA ALIMENTAZIONE J8 XPW R Ventola 24VDC J3 J4 J5 J7 J2 J1 RESISTENZA XR1 XR2 JF XPW R XU 2 XU 2 XU1 XU 1 Ventola 24VDC XV1 CU379 (alimentazione) C0605 (TRM-54) CU145 Conn. Volante 2 CU318 CU156 CU010 CU011

42. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.4 3.3. VISIO DISPLAY BOARD 3.3.1. CPU B OARD : 700V ISIO MODELS The Circuit Board includes: a microprocessor, its control logic, a first FLASH EPROM (containing the Operating System), a second FLASH EPROM, partitioned in two sections (HD1 and HD2) the first us ed for the training program of the machine, for storing video and other information/support material, the second partition for saving messages coming from the COMMUNICATOR and a third FLASH EPROM (HD3) used for a back - up process . It is the Circuit Board th at connects all components of the display and acts as point of connection to the driver. The main functions of the board are: Manages and process signals from:  LCD;  LCD Inverter;  Touch Screen;  Digital /Analogue tuner Board;  LAN network board (integrated );  Wireless network Board;  Emergency button;  HS/HR Cardio Receiver;  Audio/Video external device Connectors Board;  Headphone Jack;  C - Safe (integrated);  Service USB port (integrated). Optional:  Dual TGS Reader;  User USB port;  iPod docking station. Distrib utes the voltages received from the low kit driver; Exchanges, over the RS - 485 serial link to the driver box, commands for controlling the belt and elevation motors; Exchanges, over the RS - 485 serial link to the driver box, commands for controlling emergen cy signals ; Controls the LEDs and the 7 - segment displays which provide feedback about the exercise session . The board includes the following indicator LED: LED mane Colour Description LED 1 GREEN if ON, the +12 Vdc power supply from the Driver correctl y reaches the board. 3.3.1.1. Backup battery The CPU board has a battery that act to maintain powered the internal clock when the machine is not connected to a power source.

23. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.11 2.9.3. D RIVER : ALE MET CE 100 - 120V 2.9.3.1. ALE MET CE + LED SCATOLA AZIONAMENTO SCHEDA AZIONAMENTO J8 MICRO FINE CORSA MOTORE MOTORE PENDENZA Ventola (coperchio) POWER SUPPLY BOX INTER- RUTTORE ON/OFF C I R C U I T B R E A K E R VAC C I R C U I T B R E A K E R SCHEDA FILTRO J3A J4 J5 J7 J2 J1 RESISTENZA COVER XS1 Ventola PRESA DI ALIMENTA- ZI ONE CU143 CU143 IN2 IN1 4 1 L N CU143 5 2 CU177 FE CU145 OUT1 OUT2 DISPLAY (LED) H.SINK XP1 CU139 (alimentazione) CU144 CU156 C0605 (TRM-54) FE A FE CN CN 2.9.3.2. ALE MET CE + VISIO SCATOLA AZIONAMENTO SCHEDA AZIONAMENTO J8 MICRO FINE CORSA MOTORE MOTORE PENDENZA Ventola (coperchio) POWER SUPPLY BOX INTER- RUTTORE ON/OFF C I R C U I T B R E A K E R VAC C I R C U I T B R E A K E R SCHEDA FILTRO J3A J4 J5 J7 J2 J1 RESISTENZA COVER XS1 Ventola PRESA DI ALIMENTA- ZI ONE CU143 CU143 IN2 IN1 4 1 L N CU143 5 2 CU177 FE OUT1 OUT2 DISPLAY (VISIO) H.SINK XP1 CU378 (alimentazione) CU144 CU156 ALIMENTATORE SUPPLEMENTARE C0605 (TRM-54) Conn. Volante 2 CU145 CU318 FE A FE CN CN

18. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.6 2.6. MECHANICAL CHARACTER ISTICS MECHANIC AL CHARACTERISTICS Length (mm – in) 2190mm – 86,2” Width (mm – in) 960mm – 38” Height (mm – in) 1552mm – 61” Weight (Kg – lbs) 195Kg – 430lbs Running surface (Width.) mm - in 520mm – 20,5” Running surface (depth.) mm - in 1520mm – 60” Running surfac e Height from ground 280mm – 11” 2.6.1. O VERALL DIMENSIONS

10. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page vi 11. SCHEDULED MAINTENANC E ................................ ................................ ................................ ......................... 11.1 11.1. ORDINARY MAINTENANCE OPERATIO N ................................ ................................ ................................ .......... 11.2 11.1.1. Setting up the operation (Daily) ................................ ................................ ................................ ........ 11.2 11.1.2. External cleaning ope rations (Daily) ................................ ................................ ................................ 11.2 11.1.3. Internal cleaning operations (Monthly) ................................ ................................ ............................. 11.2 11.1.4. Checking the “Emergency stop” (Monthly) ................................ ................................ ...................... 11.2 11.1.5. Complete operation (six - menthly) ................................ ................................ ................................ ..... 11.2 11.2. EXTRA - ORDINARY MAINTENANCE OPERATIO NS ................................ ................................ ......................... 11.3 11.2.1. Checking the operation of the cardiotester receiver ................................ ................................ ......... 11.3 11.2.2. Checking the operation of the hand sensor receiver ................................ ................................ ......... 11.3 11.2.3. Checking the working conditions ................................ ................................ ................................ ...... 11.3 11.2.4. Checking the state of wear of tread belt and running deck ................................ ............................... 11.3 11.2.5. Checking the wear of the motor roller ................................ ................................ ............................... 11.3 11.2.6. Checking the state of wear of the driving roller ................................ ................................ ................ 11.3 11.2.7. Checking the shock absorbers ................................ ................................ ................................ ........... 11.3 11.2.8. Checking the tread belt motor drive - belt ................................ ................................ ........................... 11.4 11.2.9. Checking and centerin g the tread belt ................................ ................................ ............................... 11.4 11.2.10. Checking the wiring and connections ................................ ................................ ................................ 11.4 11.2.11. Checking the display ................................ ................................ ................................ .......................... 11.4 12. APPENDIX ................................ ................................ ................................ ................................ ............................. 12.1 12.1. M ENU PASSWORD TABLE ................................ ................................ ................................ ................................ .. 12.1 12.2. R EQUIRED T OOLS ................................ ................................ ................................ ................................ ............. 12.2

105. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.35 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Place the tester probes across pins 1 and 2 on the connector HD4 of the receiver. The measured value should be +5Vdc. (2) As at step (1) but on pins 1 e 5 on CN9 connector ( ARM Board ) or on CN31 connector ( CPU B oard ); of the CU135 cable . (3) Check the correct display SW version, according to the “EXCITE SW SMART TABLE” you can find in TG Direct ,“NEWS” section. Check the grounding of the HR/HS Receiver Board , measuring the resistance value between: 1. The ground fast on of HR/HS Receiver Board and the ground node on the Power supply box of the machine; 2. The ground node of the power entry module and the main wall socket. The measured value should be approximately lower than 1Ω (Ohm). Check finally the grounding of the m ain wall socket, measuring that the following voltages are present: P – N (phase – neutral) = 220Vac / 110Vac P – G (phase – ground) = 220Vac / 110Vac N – G (neutral – ground) = 0Vac (4) Check if the receiver has been correctly mounted on the machine, as detail at paragraph: 7.6. “ Disassembling the HS/HR cardio receiver ”. If you replace CPU/ARM Board, check that its SW version is updated, otherwise install the last ver sion.

50. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.12 3.12. LOW KIT 3.12.1. ALE MET CE DRIVER This is the electronic device that receives the line voltage and, through a PFC module, it rectifies the voltage to the 400Vdc used to generate the 3 phase voltage for the belt motor. It generates the DC voltages to power up all the other devices of the machine. It’s the device that acts as an interconnection hub for the main components of the lower assembly, and serves as the point of connection with the display. In fact:  it supplies the +12Vdc voltages to the display;  it supplies the tread belt motor with a variabl e - frequency sinusoidal voltage: varying the frequency varies the speed of rotation of the motor, and consequently the speed of the tread belt;  it exchanges, over the RS - 485 serial link to the Display Board, the commands for controlling the tread belt and e levation motors;  it exchanges, over the RS - 485 serial link to the Display Board, the commands for viewing and configuring the inverter parameters;  it exchanges, over the RS - 485 serial link to the Display Board the commands for viewing the errors logged by the inverter. From the outside the following indicator LEDs are visible: LED NAME COLOUR DESCRIPTION H6 GREEN +5Vdc (if ON proper functioning) H3 GREEN +12Vdc (if ON proper functioning) H4 GREEN +24Vdc (if ON proper functioning) H5 BLUE 400Vdc (if ON proper functioning) The board includes the following indicator LEDs visible when the driver cover is removed: LED NAME COLOUR DESCRIPTION ALARM RED If ON indicates that the Driver has detected an error (EdC) when it was moving the elevation motor. Thi s LED stay ON for about 1 second and then goes OFF. EN_UP GREEN if ON indicates that the motor has received the supply voltage for movement in the upward direction EN_DOWN RED if ON indicates that the motor has received the supply voltage for movement in the downward direction TACHO GREEN functioning of elevation motor encoder: if blinking, indicates that the board is receiving the pulses from the encoder DWN_SW GREEN status of Limit switch contact: if ON indicates that the microswitch is pressed

102. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.32 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Place the tester probes across pins 1 and 2 on the connector HD4 of receiver. The measured value should be +5Vdc. (2) As for step (1) but across pins 1 and 5 of connector CN 10 ( ARM Board ) and on the CN25 connector ( CPU Board ); of CU 244 cable. (3) Check the corr ect display SW version, according to the “EXCITE SW SMART TABLE” you can find in TG Direct ,“NEWS” section. Check the grounding of the HR/HS Receiver Board , measuring the resistance value between: The fast - on on the HR/HS Receiver Board and the ground no de on the power entry module; The ground node of the power entry module and the main wall socket. The measured value should be approximately lower than 1Ω (Ohm). Check finally the grounding of the main wall socket, measuring that the following voltages ar e present: P – N (phase – neutral) = 220Vac / 110Vac P – G (phase – ground) = 220Vac / 110Vac N – G (neutral – ground) = 0Vac (4) Check that: The fast on of the cable are well connected to the Hand Sensor plates; The continuity of the signal between the Hand Sensor plates and the relevant pin on HD3&2 connector of the receiver, referring to the paragraph: 2.10. “ Cables ”; There is NO continuity between the HS plates and the ground fast on the receiver (otherwise the signals are grounded).

52. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 3.14 3.13.1. AT - UL DRIVER It’s the device that acts as an interconnection hub for the main components of the lower assembly, and serves as the point of connection with the display. In fact:  it exchanges, over the RS - 485 serial link to the CPU/ARM board, the commands for controlling the tread belt and elevation motors;  it supplies the tread belt motor with a variable - frequency sinusoidal volt age: varying the frequency varies the speed of rotation of the motor, and consequently the speed of the tread belt;  it supplies the elevation motor with a 24Vdc;  it exchanges, over the RS - 485 serial link to the CPU/ARM board, the error signals pertaining t o the tread belt and elevation motors;  it exchanges, over the RS - 485 serial link to the CPU/ARM board, the commands for viewing and configuring the inverter parameters;  it exchanges, over the RS - 485 serial link to the CPU/ARM board, the commands for viewin g the errors logged by the inverter.  Receives the mains voltage at its inputs and outputs the DC supply voltages for the machine circuit boards listed below: Supply voltage Connector Description +24Vdc XU1 Power supply for the fans of the electrical box +5Vdc XU1 Power supply for belt and elevation motor encoders +5Vdc +12Vdc XU2 Power supply for display From the outside the following indicator LEDs are visible: LED name Colour Description H2 GREEN +5Vdc H3 GREEN +12Vdc H4 GREEN +24Vdc H5 RED 400 Vdc It contains:  The AT driver board  The AT power supply board  2 fans  A breaking resistor

20. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.8 2.8. CONFORMITY TO REGULA TIONS EUROPE Europe MD USA MET USA EMI regulations EN61000 – 6 – 1 (2001) EN55022 (2000) class A EN61000 – 3 – 2 (2002) EN61000 – 3 – 3 (1997) EN60601 - 1 EN60601 - 1 - 2 EN957 - 1 EN957 - 6 class SB FCC15 FCC15 El ectrical safety regulations EN60335 – 1 (2008) - UL1647 UL60601 - 1 Mechanical safety regulations EN957 – 1 (2006) EN957 – 6 (2003) class SB - - - Directives 2006/42/CE 2004/108/CE 2006/95/CE - - - Moreover :  Risk category under 93/42/CEE: Class IIa (o nly for MD models),  Electrical isolation class of the EN60601 - 1: Class I ,  Applied parts : Type B (only for MD models),  Applied parts of the heart rate monitor transmitter : Type BF (only for MD models) ,  Protection rating: IP20 .

92. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.22 Error code Error Description Possible solution 12 12/OLr Braking resistor overload. • Check the resistor=150 Ω; • low kit Driver. 19 19/EM EMERGENCY. Is generated when low kit drive receives a software emergency signal that is not accompanied by a hardware emergency signal - 20 20/SFAn LOW KIT DRIVER COVER PLATE FAN. This error is generated if there is a malfunction on the fan mounted on the driver’s cover plate, for at least 5 sec. • low kit driver cover plate fan. 21 21/PFAn LOW KIT DRIVER INTERNAL FAN. This error is generated if there is a malfunction on the internal low kit driver fan, fo r at least 5 sec • low kit driver internal fan. 22 22/IMV INVERTER POWER SUPPLY: This error is generated if a voltage <156 VAC for at least 1 sec. when the AC motor is working or for at least 10 sec. when AC motor is not working. - 23 23/SHC SHORT CIRCUIT. Is generated in the event of a short circuit between a motor phase and earth. • Check the belt motor. 24 24/OHS OVERHEATING of the dissipater sensor: This error is generated if a malfunction of the dissipater sensor last more than 1 sec. • low kit driver; • ( *). Note (*): In case of errors related to high current consumption (such as E01), we recommend performing a test that consists of walking on the treadmill at a pre - established speed and checking the current consumption, according to the table below. U SER WEIGHT FREQUENCY/SPEED CURRENT DRAW 60Kg 1500Hz / 5Km/h 5A 70Kg 1500Hz / 5Km/h 5.3A 80Kg 1500Hz / 5Km/h 5.6A On models not equipped with an encoder, in which the speed readout is always "0", use the frequency value given in the table as a referenc e.

28. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.16 2.10. C ABLES The colour of the cables can be changed, refer in particular to the Pin Out. 2.10.1. CBQ CABLES CBQ32: TGS cable (Patch conn. – CPU / ARM Board) ARM Board CN4 CPU Board CN19 Signal Colour Patch Conn. 1 +12Vdc power su pply Red 8 3 RX Brown 1 5 TX Blue 2 9 GND Black 6 2.10.2. AUTOTRA N SFORMER CABLE AUTOTRANSFORMER cable (Autotransformer – Power supply box – ALE Driver) Autotransformer Signal Power Supply box ALE Driver: J1 Cable internally connected (PHASE) 110Vac Power Sup ply 1 (NEUTRAL) 110Vac Power Supply 2 (PHASE) 220Vac Power Supply 1 (NEUTRAL) 220Vac Power Supply 2

215. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 12.1 12. APPENDIX 12.1. MENU PASSWORD TABLE The configuration menus available and their corresponding access pa sswords are shown below: PASSWORD LIST Assistenza Service 2501 VisioWEB 2501 Configurazione tecnica; Technical configuration; LED VISIO 2502 Upload/ Network page; VISIO 2503 Scrivi il Serial Number; Write Serial Number; VISIO 2512 Accesso ambien te Windows; Windows screen; VISIO 2612 Selezione tipo macchina; Machine type selection; VISIO 2411 Troubleshooting; LED VISIO Utente User 2406 VisioWEB 2404 Configurazione IP - TV; IP - TV configuration; VISIO 2405 Configurazione IP - Radio; IP - Radio configuration; VISIO 2406 Configurazione Utente + letture Serial Number; User Configuration + Serial number reading; LED VISIO 2407 Sintonizzazione canali Analogici e Digitalli TV; Analog and Digital TV channels tuning; VISIO 2408 Sintonizzazione canali Analogici e Digitalli Radio; Analog and Digital Radio channels tuning; VISIO 2409 Calibrazione Touch Screen; Touch Screen calibration; VISIO 2412 Menù personalizzazione profile utente; Training profile menù (to add and customize personal profiles); LED VISIO 2413 Configurazione Network; Network configuration; VISIO - Configurazione VISIOWEB Bookmarks; VISIOWEB Bookmarks configuration; -

13. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.1 2. TECHNIC AL CHARACTERISTICS 2.1. PRODUCT CODES The machine codes take into account all the possible variants and options available for the products. The machine code, which does not include the Serial Number, consists of 16 alphanumeric characters arranged as follows: Characters Description Key to values 1,2, Line type DA = Excite + 3, Machine type K = RUN Now 4, Model, 6 = 500 8 = 700 9 = 900 5, Type of power supply 1 = 100 - 120V – MET CE 2 = 200 - 240V – MET CE E = 200 - 240V – CE U = 90 - 265V – AT - UL M = Medical Devi ce - CE 6, Type of Display L = LED C = VISIO W = VisioWEB 7, Integrated accessories N = None T = Wellness System I = iPod + USB A = iPod + USB + WS 8, 9, Colour of the frame AL = Silver AN = Antracite 10, 11, Colour of upholstery 00 = None AG = Grigio K0 = Blu M0 = Bordeaux NA = Nero Z0 = Marrone 12, Guards colour G = Flint grey R = Renault grey 13, TV standard 0 = None D = DVB - T A = ATSC I = ISDB - T

202. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.28 9.5.1.1. Table of configuration parameters (VISIO): To correctly display the parameter values, you need to load them from the low kit, using the “Read from low kit” function. After any changes to the paramet er values, you need to save them in the low kit using the “Write to low kit” function. Display parameter Unit of measure Description VISIO Default values P01 Kmh*10 Default linear speed 8 P02 (Kmh*100)/sec Default acceleration and deceleration 100 P 03 %*2 default slope set point 0 P04 Numerical Constant PID proportional gain 7 P05 Numerical Constant PID Integral gain 150 P06 Numerical Constant S Ramp Type 0 P07 on/off Flag DC motor encoder signal alarm action 0 P08 10msec Watchdog serial commun ication 0 P09 1msec DC motor encoder error timeout 1 cnt = 100 msec 15 P10 on/off Flag signal receiving Sw Emergency and not receiving Emergency Hw 0 P11 mm roll diameter 91 P12 Numerical constant*100 roller diameter 200 P13 on/off Flag posting warnin g signal AC motor encoder 0 I.e.  P01 = kmh = 8 / 10 is the 0.8kmh of start, (as if the unit was hundreds of meters times).  P02 = 100 means the acceleration expressed in kmh/sec is 100 / 100 = 1 where the 100 is the value of the numerator and the denomin ator is the default 100 of formula. (cents of kmh/sec)  P03moltiplication by two is to take steps to 0.5%, this basically 2 means 1%.  Numerical Constant: P04 - P05 - P06 is a pure number, multiplicative constant used by the firmware.  P07, P10, P13 is a Boolean flag, yes or not.  P08 is expressed in tens of msec: if P08 = 100 will be a second.  P12 = 211 means that the transmission ratios is 2.11.

91. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 6.21 6.12. DRIVER ERRORS When the Driver detects an error, it stops and interrupts the power supply to the tread belt and elevation motor and an error code identifying the fault condition is saved in the error history log. In addition, it sends an error status signal to the CPU/ARM board via the serial link. Upon receiving this error signal, the CPU/ARM board halts the exercise and sh ows the “THE EQUIPMENT IS BLOCKED” message on the display. The errors logged by the inverter can also be viewed as described in the relevant paragraph of the Service menu. The following table provides the correspondence between error codes, meaning and po ssible solutions: Error code Error Description Possible solution 01 1/OH OVERHEATING of the heat sinks of the low kit driver and of the PFC. • Check the running belt; • Check the running deck; • Check the fans; • low kit driver; • (*). 02 2/OC OVERCURRENT, even i f only temporary, on the inverter output. • Check the running deck; • low kit driver; • Check P409 (torque) = 100 - 115; • (*). 03 3/UU UNDERVOLTAGE condition, due to an even temporary drop in line voltage. • Bad power distribution line of 110/220 Vac; • Voltage NOT c onstant; • (*). 04 4/OU OVERVOLTAGE • Voltage NOT constant; • Braking resistor. 05 5/ST SERIAL TIMEOUT, there is no signals exchange between high kit and low kit • Check the serial communication. 06 6/PE EEPROM error: is generated when there is an error detect ed in the data stored on the Eprom. • low kit Driver. 07 7/EdC1 ELEVATION MOTOR ENCODER error. • Check Up/Down Troubleshooting. 08 8/EdA BELT MOTOR ENCODER error. • Encoder; • low kit Driver; • Check P409 (torque) = 100 - 115. 09 9/OtM BELT MOTOR THERMAL CUT - OUT open. • Update driver SW; • Check motor casing fan; • Check the running belt; • Check the belt motor. 10 10/Oli Inverter overload caused by a DC current exceeding, for the maximum allowed time (I2t), the maximum permissible threshold for the inverter. • (*). 11 11/OLm Motor overload caused by a DC current exceeding, for the maximum allowed time (I2t), the maximum permissible threshold for the motor in question. -

191. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.17 9.3.3.3. Default Setting To load the default parameter values, scroll using the +/ - effort level keys until the display shows: DEFAULT SETTING ? press ENTER to write the default values to the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. To write these parameters to the low kit, use the “Write to low kit” function. 9.3.3.4. Table of configuration parameters (LED): Display parameter Unit of measure Description LED Default valu es P01 Kmh*10 Default linear speed 8 P02 (Kmh*100)/sec Default acceleration and deceleration 100 P03 %*2 default slope set point 0 P04 Numerical Constant PID proportional gain 7 P05 Numerical Constant PID Integral gain 150 P06 Numerical constant S Ra mp Type 0 P07 on/off Flag DC motor encoder signal alarm action 0 P08 10msec Watchdog serial communication 0 P09 1msec DC motor encoder error timeout 1 cnt = 100 msec 15 P10 on/off Flag signal receiving Sw Emergency and not receiving Emergency Hw 0 P1 1 mm roll diameter 91 P12 Numerical constant*100 roller diameter 200 P13 on/off Flag posting warning signal AC motor encoder 0 I.e.  P01 = kmh = 8 / 10 is the 0.8kmh of start, (as if the unit was hundreds of meters times).  P02 = 100 means the accelerat ion expressed in kmh/sec is 100 / 100 = 1 where the 100 is the value of the numerator and the denominator is the default 100 of formula. (cents of kmh/sec)  P03moltiplication by two is to take steps of 0.5%, this basically 2 means 1%.  Numerical Constant: P0 4 - P05 - P06 is a pure numbers, multiplicative constants used by the firmware.  P07, P10, P13 is a Boolean flag, yes or not.  P08 is expressed in tens of msec: if P08 = 100 will be a second.  P12 = 211 means that the transmission ratios is 2.11.

29. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.17 2.10.3. TRM CABLES TRM - 31: C - Safe Signal cable (LED only) (ARM Board – C - Safe Board ) ARM Board CN1 Signal Colour C - Safe Board CN1 1 Digital #1 Flat c able 1 ... ... ... ... 14 Digital #14 Flat cable 14 TRM - 54: Limit Switch cable (ALE/AT UL Driver – Limit Switch) ALE/AT UL driver J8 Signal Colour Limit Switch 3 Contact White Fast - on 8 Reference Brown Fast - on TRM - 29: Up - Down and Speed Joystick cable (CP U / ARM Board – Joystick) Boards CPU: CN16/17 ARM: CN11/13 Signal Colour Micro Joystick Up Down 1 Reference - White - Faston (C) 2 Grade - Brown - Faston (NA) 3 Reference + Green Faston (C) - 4 Grade + Yellow Faston (NA) -

14. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.2 Characters Description Key to values 14,15, Language, 00 = Multi - language BR = Portuguese CN = Chinese DA = Danish DE = German ES = Spanish FR = French IT = Italian JP = Japanese NL = Dutch RU = Russian TR = Turkish UK = British English US = American English 16. Type of packing. A, B, C, D, E, F, G, H, I, J, K, S, U See the table below. DAK81WAAN00RD00E all of the Excite + line machines will be shipped with the specific power cable for the destination country. In particular this means a cable with the standard plug used in the installation country . This implementation also means a change in the product code. Specifically the last character of the product code will be characterised based on the options shown in the table below: 16th Character Product code Main country of use Plug standard Type of packaging A Australia A S /NZS 3112 Overseas B Brazil NBR 14136 Overseas C China CPC S - CCC Overseas D South Africa SANS 164 - 2 Overseas E Europe (EC) EEC 7/16 European F USA (UL 250 V) NEMA 5 - 15/ NEMA 5 - 20 Overseas G Great Britain BS1363 European H Argentina IRAM 2073 Oversea s I Italy EEC 7/16 Italy J Japan JIS 8303 Overseas K Great Britain BS1363 Overseas S Europe (EC) EEC 7/16 Overseas U USA (UL 110 V) NEMA 6 - 15/ NEMA 6 - 20 Overseas As shown in the table above, the 16th character also identifies the type of packaging d epending on the destination country, i.e. DAK81WAAN00RD00 E .

5. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page i Contents 1. GENERAL NOTICES ................................ ................................ ................................ ................................ ............. 1.1 1.1. I NTRODUCTION ................................ ................................ ................................ ................................ ................... 1.1 1.2. R ECOMMENDATIONS ................................ ................................ ................................ ................................ .......... 1.1 1.3. G ENERAL RULES FOR REP AIR PROCEDURES ................................ ................................ ................................ ........ 1.2 2. TECHNICAL CHARACTERI STICS ................................ ................................ ................................ .................... 2.1 2.1. P RODUCT CODES ................................ ................................ ................................ ................................ ................ 2.1 2.2. S ERIAL N UMBER STRUCTURE ................................ ................................ ................................ ............................. 2.3 2.3 . C OLOUR O PTIONS ................................ ................................ ................................ ................................ ............... 2.3 2.4. P OWER REQUIREMET ................................ ................................ ................................ ................................ .......... 2.4 2.5. T ECHNICAL SPECIFICATI ON ................................ ................................ ................................ ................................ . 2.4 2.6. M ECHANICAL CHARACTERI STICS ................................ ................................ ................................ ........................ 2.6 2.6.1. Overall dimensions ................................ ................................ ................................ .............................. 2.6 2.6.2. european and overseas pACKING dimension s ................................ ................................ .................... 2.7 2.7. A MBIENT SPECIFICATION S ................................ ................................ ................................ ................................ .. 2.7 2.8. C ONFORMITY TO REGULAT IONS ................................ ................................ ................................ .......................... 2.8 2.9. W IRING DIAGRAMS ................................ ................................ ................................ ................................ ............. 2.9 2.9.1. Kit Basso ................................ ................................ ................................ ................................ .............. 2.9 2.9.1.1. ALE MET CE ................................ ................................ ................................ ................................ .............................. 2.9 2.9.1.2. AT - UL ................................ ................................ ................................ ................................ ................................ .......... 2.9 2.9.2. Driver: AT - UL 100 - 120V ................................ ................................ ................................ .................. 2.10 2.9.2.1. AT - UL + LED ................................ ................................ ................................ ................................ ............................ 2.10 2.9.2.2. AT - UL + VISIO ................................ ................................ ................................ ................................ ......................... 2.10 2.9.3. Driver: ALE MET CE 100 - 120V ................................ ................................ ................................ ....... 2.11 2.9.3.1. ALE MET CE + LED ................................ ................................ ................................ ................................ ................ 2.11 2.9.3.2. ALE MET CE + VISIO ................................ ................................ ................................ ................................ ............. 2.11 2.9.4. Driver: ALE MET CE 200 - 240V ................................ ................................ ................................ ....... 2.12 2.9.4.1. ALE MET CE + LED ................................ ................................ ................................ ................................ ................ 2.12 2.9.4.2. ALE MET CE + VISIO ................................ ................................ ................................ ................................ .............. 2.12 2.9.5. High Kit ................................ ................................ ................................ ................................ ............. 2.13 2.9.5.1. 500 model Display (ARM Board) ................................ ................................ ................................ .............................. 2.13 2.9.5.2. 700/900LED Display (ARM Board) ................................ ................................ ................................ .......................... 2.14 2.9.5. 3. 700/900VISIO Display (CPU Board) ................................ ................................ ................................ ......................... 2.15 2.10. C ABLES 2.16 2.10.1. CBQ cables ................................ ................................ ................................ ................................ ........ 2.16 2.10.2. AUTOTRAnSFORMER cable ................................ ................................ ................................ ............ 2.16 2.10.3. TRM cables ................................ ................................ ................................ ................................ ........ 2.17 2.10.4. Cavi CU ................................ ................................ ................................ ................................ ............. 2.18 3. PRINCIPLES OF OPERAT ION ................................ ................................ ................................ ............................ 3.1 3.1. B LOCK DIAGRAMS WITH ALE D RIVER ................................ ................................ ................................ ................ 3.1 3.1.1. ALE Driver (220 V – 110V) ................................ ................................ ................................ .................. 3.1 3.1.2. AT - UL Driver ................................ ................................ ................................ ................................ ...... 3.2 3.2. LED DISPLAY BOARDS ................................ ................................ ................................ ................................ ........ 3.3 3.2.1. ARM Board: 500 and 700 models ................................ ................................ ................................ ....... 3.3 3.3. VISIO DISPLAY BOARD ................................ ................................ ................................ ................................ ....... 3.4 3.3.1. CPU Board: 700Visio models ................................ ................................ ................................ ............. 3.4 3.3.1.1. Backup battery ................................ ................................ ................................ ................................ ............................. 3.4 3.3.2. LCD inverter ................................ ................................ ................................ ................................ ........ 3.5 3.3.3. Digital/Analogue tuner board ................................ ................................ ................................ ............. 3.5 3.3.4. Integrated LAN network board (Wired) ................................ ................................ ............................... 3.5 3.3.5. Wireless network board (without cables) ................................ ................................ ............................ 3.6 3.3.6. Audio/Video external device connector board ................................ ................................ .................... 3.7 3.3.7. Headphone jack ................................ ................................ ................................ ................................ ... 3.7 3. 3.8. C - Safe board (integrated): ................................ ................................ ................................ .................. 3.7

16. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.4 2.4. POWER REQUIREMET POWER REQUIREMENT E = CE 200 - 240V (50 - 60Hz) (It is advisable 16A dedicated socket each machine) 1 = MET CE 100 - 120V (50 - 60Hz) (It is advisable 16A dedicated socket each machine) 2 = MET CE 200 - 240V (50 - 60Hz) (It is advisable 16A dedicated socket each machine) U = AT - UL 90 - 265V (50 - 60Hz) (It is advisable 16A dedicated socket each machine) 2.5. TECHNICAL SPECIFICAT ION MODELS 500 LED 700 LED 700 VISIO 900 LED 900 VISIO Power engine: 4400Watt - 6HP (AC) Energy consumption: 1800Watt 2200Watt 2500Watt Stand - By consumption: LED + (ALE MET CE 200 - 240V) 34,6Watt - 34,6Watt - Stand - By consumption: LED + (ALE MET CE 100 - 120V): 40,9Watt 40,9Watt Stand - By consumption: VISIO + (ALE MET CE 200 - 240V): - 81,4Watt - 81,4Watt Stand - By consumption: VISIO + (ALE MET CE 100 - 120V): 87,7Watt 87,7Watt Speed (220V) : 0,8 - 20 km/h (220Vac) 0,8 - 25 km/h (220Vac) 0,8 - 27 km/h (220Vac) Speed (110V - 90V) : 0,8 - 20 km/h (110Vac - 90Vac) 0,8 - 22 km/h ( 110Vac) 0,8 - 20 km/h (90Vac) 0,8 - 22 km/h (110Vac) 0,8 - 20 km/h (90Vac) Max user weight (Kg – lbs): 220kg – 485lbs Incline : 0 - 15 % (± 1%) 0 - 18 % (± 1%) HR monitoring Hand sensor, Telemetry Fast Track Control con Visual Setup: NO SI Runner detection sys tem: SI InMotion - Safety System: SI Integrated adjustable fan:: NO SI Calorie Coach: SI

30. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.18 2.10.4. C AVI CU CU132: TGS Sig nal cable (Patch Conn. – Dual TGS reader) Patch Conn. Signal Colour Dual TGS reader CN1 8 +12Vdc power supply Black 2 1 RX Green 1 2 TX Black 4 6 GND Black 5 CU136: Hand Sensor Signal cable (Cardio Receiver – Hand Sensor L / R ) Cardio Receiver HD3&2 Signal Colour Hand Sensor (L) Hand Sensor (R) Up Down Up Down 1 Right hand signal input Black - - faston - 2 Right hand contact ref Black - - - faston 3 Shield GND Black - - - - 4 Left hand signal input Black faston - - - 5 Left hand contact ref B lack - faston - - CU145: Power Supply cable (Filter Board / Patch conn.) Filter Board OUT1/OUT2 Signal Colour Patch Conn. 2 Fast - on Phase Black 1 Fast - on Neutral Black 2 CU227: Ready to Run cable (“InMotion”) ( InMotion Board – ARM /CPU Board ) InMoti on Board Signal Colour ARM Board : CN23 CPU Board: CN34 1 Vcc +5 Brown 1 2 En Light Green 4 3 GND +5 White 8

6. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page ii 3.3.9. Service USB port (integrated): ................................ ................................ ................................ ............ 3.7 3.4. OPTIONAL ................................ ................................ ................................ ................................ ....................... 3.8 3.4.1. iPod docking station ................................ ................................ ................................ ............................ 3.8 3.4.1.1. Client USB port ................................ ................................ ................................ ................................ ........................... 3.8 3.4.1.2. Dual TGS reader ................................ ................................ ................................ ................................ .......................... 3.8 3.5. CARDIO RECEIVER BOAR D ................................ ................................ ................................ ................................ ... 3.9 3.5.1. HR/HS (Chest belt/Hand Sensor) ................................ ................................ ................................ ........ 3.9 3.6. E MERGENCY BUTTON ................................ ................................ ................................ ................................ ....... 3.10 3.7. C - S AFE BOARD ................................ ................................ ................................ ................................ ................. 3.10 3.8. B ELT MOTOR ................................ ................................ ................................ ................................ .................... 3.10 3.9. E LEVATION MOTOR ................................ ................................ ................................ ................................ .......... 3.10 3.10. J OYSTICK ................................ ................................ ................................ ................................ .......................... 3.11 3.11. L IMIT SWITCH ................................ ................................ ................................ ................................ ................... 3.11 3.12. L OW K IT ................................ ................................ ................................ ................................ ........................... 3.12 3.12.1. ALE MET CE driver ................................ ................................ ................................ .......................... 3.12 3.12.2. ALE power supply box ................................ ................................ ................................ ....................... 3.13 3.12.3. Supplementary power supply ................................ ................................ ................................ ............. 3.13 3.13. A UTOTRANSFORMER ................................ ................................ ................................ ................................ ........ 3.13 3.13.1. AT - UL driver ................................ ................................ ................................ ................................ ..... 3.14 3.13.2. AT - UL driver box ................................ ................................ ................................ .............................. 3.15 3.13.3. AT - UL power supply board ................................ ................................ ................................ ............... 3.15 3.13.4. Fans ................................ ................................ ................................ ................................ ................... 3.15 3.13.5. Breaking resistor ................................ ................................ ................................ ............................... 3.15 3.13.6. Power supply box ................................ ................................ ................................ .............................. 3.15 3.14. T READ BELT MOTOR DRIV E ................................ ................................ ................................ .............................. 3.16 3.14.1. Mechanics ................................ ................................ ................................ ................................ .......... 3.16 3.14.2. Controls ................................ ................................ ................................ ................................ ............. 3.16 3.14.3. The signals involved ................................ ................................ ................................ .......................... 3.17 3.15. E LEVATION MOTOR DRIVE ................................ ................................ ................................ ................................ 3.18 3.15.1. Mechanics ................................ ................................ ................................ ................................ .......... 3.18 3.15.2. Control ................................ ................................ ................................ ................................ ............... 3.18 3.15.3. Reset procedure ................................ ................................ ................................ ................................ . 3.19 3.15.4. The signa ls involved ................................ ................................ ................................ .......................... 3.20 3.16. E MERGENCY STOP SIGNAL MANAGEMENT ................................ ................................ ................................ ........ 3.21 3.16.1. Control logic ................................ ................................ ................................ ................................ ...... 3.21 3.16.2. The signals involved ................................ ................................ ................................ .......................... 3.22 4. ACCESSORIES ................................ ................................ ................................ ................................ ........................ 4.1 4.1. C ARDIO THEATER CONNEC TION ................................ ................................ ................................ .......................... 4.1 4.2. PC LINK FOR PROGRAMMING ................................ ................................ ................................ .............................. 4.2 4.3. M ONITOR PLUG FOR C - S AFE PORT ................................ ................................ ................................ ...................... 4.3 4.4. VISI OWEB U P G RADE ................................ ................................ ................................ ................................ ....... 4.3 4.4.1. VISIO vs VISIOWEB ................................ ................................ ................................ ............................ 4.3 4.4.2. VISIOWEB upgrade for VISIO models ................................ ................................ ................................ 4.3 4.4.3. UpGrade from LED to VisioWEB ................................ ................................ ................................ ........ 4.4 4.5. A CCESSORISE ................................ ................................ ................................ ................................ ..................... 4.4 5. INSTALLATION INSTRUC TIONS ................................ ................................ ................................ ...................... 5.1 5.1. S PECIFICATIONS AND RE QUIREMENTS ................................ ................................ ................................ ................. 5.1 5.2. M OVING 5.2 5.3. I NSTALLAT ION ................................ ................................ ................................ ................................ .................... 5.3 5.4. F IRST POWER - ON ................................ ................................ ................................ ................................ ................ 5.3 5.5. T O CHECK THE CORRECT OPERATION OF THE MAC HINE ................................ ................................ ...................... 5.3 5.6. S PECIFICATIONS AND A NTENNA REQUIREMENTS ................................ ................................ ................................ 5.4 6. TROUBLESHOOTING ................................ ................................ ................................ ................................ ........... 6.1 6.1. T ROUBLESHOOTING MENU S ERVICE : 500LED M ODELS ................................ ................................ ..................... 6.2 6.1.1. Automatic Tests ................................ ................................ ................................ ................................ ... 6.3 6.1.1.1. I2C Device Test ................................ ................................ ................................ ................................ ........................... 6.3

8. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page iv 7.7. D ISASSEMBLING THE FAN ................................ ................................ ................................ ................................ . 7.23 7.8. D ISASSEMBLING THE H AND S ENSOR ................................ ................................ ................................ ................ 7.24 7.9. D ISASSEMBLING THE LAT ERAL HANDLEBAR ................................ ................................ ................................ ..... 7.25 7.10. D ISASSEMBLING THE I N M OTION – (R EADY TO R UN ) BOARD ................................ ................................ ........... 7.26 7.11. D ISASSEMBLIN G THE UPPER DASHBOAR D GUARD , CENTRAL HANDLEBAR AN D THE JOYSTICKS ......................... 7.27 7.11.1. Disassembling the upper dashboard guard ................................ ................................ ....................... 7.27 7.11. 2. Disassembling the central handlebar ................................ ................................ ................................ 7.28 7.11.3. Disassembling the joystick ................................ ................................ ................................ ................. 7.29 7.12. D ISASSEMBLING THE LOW ER DASHBOARD GUAR D ................................ ................................ ............................ 7.30 7.13. D ISASSEMBLING THE LAT ERAL UPRIGHTS ................................ ................................ ................................ ......... 7.31 7.14. D ISASSEMBLING THE L OWER K IT GUARD ................................ ................................ ................................ ......... 7.33 7.14.1. Disassembling the upper guard ................................ ................................ ................................ ......... 7.33 7.14.2. Disassembling the lower guard ................................ ................................ ................................ ......... 7.34 7.15. D I SASSEMBLING THE L OWER K IT ................................ ................................ ................................ ..................... 7.35 7.15.1. Disassembling the ALE Driver ................................ ................................ ................................ .......... 7.35 7.15.2. Disassembling the AT - UL Driver ................................ ................................ ................................ ...... 7.36 7.16. D ISASSEMBLING THE POW ER SUPPLY BOX ................................ ................................ ................................ ........ 7.37 7.17. D ISASSEMBLING THE BEL T MOTOR ................................ ................................ ................................ ................... 7.38 7.18. D ISASSEMBLING THE ELE VATION MOTOR ................................ ................................ ................................ .......... 7.39 7.19. D ISASSEMBLING THE LIM IT SWITCH ................................ ................................ ................................ .................. 7.40 7.20. D ISASSEMBLING THE EXT RA POWER SUPPLY ................................ ................................ ................................ ..... 7.42 7.21. D ISASSEMBLING THE AUT OTRANSFORMER ( V . 110 V ) ................................ ................................ ........................ 7.43 7.22. D ISASSEMBLING THE RUN NING DECK AND ITS CO MPONENTS ................................ ................................ ............ 7.49 7.22.1. Disassembling the footrest ................................ ................................ ................................ ................. 7.49 7.22.2. Disassembly the driven roller ................................ ................................ ................................ ............ 7.51 7.22.3. Disassembling the transmission belt and motor roller ................................ ................................ ...... 7.52 7.22.4. Disassembling the running deck and belt ................................ ................................ .......................... 7.53 7.22.4.1. A Typology ................................ ................................ ................................ ................................ ................................ 7.53 7.22.4.2. B Typology ................................ ................................ ................................ ................................ ................................ 7.54 7.22.5. Disassembling the shock absorber ................................ ................................ ................................ .... 7.55 7.22.5.1. A Typology ................................ ................................ ................................ ................................ ................................ 7.55 7.22.5.2. B Typology ................................ ................................ ................................ ................................ ................................ 7.55 8. ADJUSTMENTS ................................ ................................ ................................ ................................ ...................... 8.1 8.1. T ENSIONING THE TREAD BELT ................................ ................................ ................................ ............................. 8.1 8.1.1. Tensioning a NEW tread belt ................................ ................................ ................................ ............... 8.1 8.1.2. Tensioning a USED tread belt ................................ ................................ ................................ ............. 8.2 8.2. C ENTRING THE TREAD BE LT ................................ ................................ ................................ ................................ 8.3 8.3. A DJUSTING THE LIMIT M ICRO SWITCH ................................ ................................ ................................ ................. 8.4 8.4. A LIGNING THE TREAD - BELT MOTOR DRIVE - BELT ................................ ................................ ................................ 8.5 8.5. T HE MACHINE IS NOT FL AT ................................ ................................ ................................ ................................ . 8.6 9. MACHINE CONFIGURATIO N ................................ ................................ ................................ ............................ 9.1 9.1. U SER MENU CONFIGURATI ON : 500 MODELS ................................ ................................ ................................ ........ 9.1 9.1.1. Language ................................ ................................ ................................ ................................ ............. 9.2 9.1.2. Distance ................................ ................................ ................................ ................................ ............... 9.2 9.1.3. Maximum exercise time ................................ ................................ ................................ ....................... 9.2 9.1.4. Cooldown time ................................ ................................ ................................ ................................ ..... 9.2 9.1.5. Pause time ................................ ................................ ................................ ................................ ........... 9.3 9.1.6. Default age ................................ ................................ ................................ ................................ .......... 9.3 9.1.7. Default weight ................................ ................................ ................................ ................................ ..... 9.3 9.1.8. Default time ................................ ................................ ................................ ................................ ......... 9.4 9.1.9. Default calories ................................ ................................ ................................ ................................ ... 9.4 9.1.10. Default distance ................................ ................................ ................................ ................................ ... 9.4 9.1.11. Enable TGS ................................ ................................ ................................ ................................ .......... 9.5 9.1.12. Enable keyboard ................................ ................................ ................................ ................................ .. 9.5 9.1.13. Modifiable target heart rate ................................ ................................ ................................ ................ 9.5 9.1.14. Enable custom messages ................................ ................................ ................................ ..................... 9.6 9.1.15. Enable Up - Down motor ................................ ................................ ................................ ...................... 9.6

7. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page iii 6.1.1.2. UpDown Test ................................ ................................ ................................ ................................ ............................... 6.3 6.1.1.3. Inverter Test ................................ ................................ ................................ ................................ ................................ . 6.3 6.1.1.4. LED Test ................................ ................................ ................................ ................................ ................................ ...... 6.4 6.1.1.5. Serial Ports Test ................................ ................................ ................................ ................................ ........................... 6.4 6.1.2. Manual Test ................................ ................................ ................................ ................................ ......... 6.4 6.1.2.1. Man. Keyboard Test ................................ ................................ ................................ ................................ ..................... 6.4 6.2. T ROUBLESHOOTING MENU : 700LED – 900LED MODELS ................................ ................................ ................... 6.5 6.2.1. Automatic Test ................................ ................................ ................................ ................................ ..... 6.6 6.2. 1.1. I2C Devices Test ................................ ................................ ................................ ................................ .......................... 6.6 6.2.1.2. Up - Down Test ................................ ................................ ................................ ................................ .............................. 6.6 6.2.1.3. Inverter Test ................................ ................................ ................................ ................................ ................................ . 6.7 6.2.1.4. LED Test ................................ ................................ ................................ ................................ ................................ ...... 6.7 6.2.1.5. Serial Ports Test ................................ ................................ ................................ ................................ ........................... 6.7 6.2.2. Manual Test ................................ ................................ ................................ ................................ ......... 6.7 6.2.2.1. Man. Keyboard Test ................................ ................................ ................................ ................................ ..................... 6.8 6.2.2.2. Man. Inverter Test ................................ ................................ ................................ ................................ ........................ 6.8 6.2.2.3. Man. UpDown Test ................................ ................................ ................................ ................................ ...................... 6.8 6.3. T ROUBLESHOOTING MENU ................................ ................................ ................................ ................................ .. 6.9 6.4. T HE DISPLAY FAILS TO ILLUMINATE ................................ ................................ ................................ .................. 6.10 6.4.1. LED Models ................................ ................................ ................................ ................................ ....... 6.10 6.4.2. VISIO Models ................................ ................................ ................................ ................................ .... 6.12 6.5. T HE TOUCH SCREEN DOES NOT WORK / IT ’ S NOT CALIBRATED ................................ ................................ .......... 6.16 6.6. N O AUDIO SOUND ................................ ................................ ................................ ................................ ............. 6.16 6.7. N O TV PICTURE ................................ ................................ ................................ ................................ ................ 6.16 6.8. T HE RADIO DOES NOT PL AY ................................ ................................ ................................ .............................. 6.16 6.9. T HE I P OD DOES NOT WORK ................................ ................................ ................................ ............................... 6.17 6.10. T HE DISPLAY SHOWS “PRESS A KEYS / T OUCH THE S CREEN ” ................................ ................................ ....... 6.19 6.11. “THE EQUIPMENT IS LOCKED (COM)” MESSAGE ON DISPLAY ................................ ................................ . 6.20 6.12. DRIVER ERRORS ................................ ................................ ................................ ................................ ................ 6.21 6.13. T READ BELT MOTOR IS J ERKING ................................ ................................ ................................ ........................ 6.23 6.14. “GRADIENT NOT WORKING” MESSAGE ON THE DISPL AY ................................ ................................ .......... 6.24 6.15. T HE MACHINE DOES NOT READ THE TG S ................................ ................................ ................................ .......... 6.27 6.16. T HERE IS NO HEART RAT E SIGNAL ................................ ................................ ................................ ..................... 6.29 6.16.1. HR/HS RECEIVER (Hand Sensor) ................................ ................................ ................................ .... 6.29 6.16.2. HR/HS Receiver (Chest Belt) ................................ ................................ ................................ ............. 6.33 6.17. T HE TELEMETRIC HEART RATE SIGNAL IS INCOR RECT ................................ ................................ ....................... 6.36 6.17 .1. Chest Belt ................................ ................................ ................................ ................................ .......... 6.36 6.17.2. Hand Sensor ................................ ................................ ................................ ................................ ...... 6.40 7. PART DISASSEMBLY ................................ ................................ ................................ ................................ ........... 7.1 7.1. D ISASSEMBLING THE DIS PLAY ................................ ................................ ................................ ............................ 7.1 7.1.1. LED Display ................................ ................................ ................................ ................................ ........ 7.1 7.1.2. VISIO Display ................................ ................................ ................................ ................................ ...... 7.2 7.2. D ISASSEMBLING BOARDS AND COMPONENTS ................................ ................................ ................................ ...... 7.3 7.2.1. LED Display (ARM Board) ................................ ................................ ................................ ................. 7.3 7.2.2. VISIO 19” Display ................................ ................................ ................................ .............................. 7.4 7.2.2.1. Wireless board (A) ................................ ................................ ................................ ................................ ....................... 7.5 7.2.2.2. DVB - T Tuner Board (B ) ................................ ................................ ................................ ................................ .............. 7.7 7.2.2.3. Tuner board ATSC (B1 ) and ISDB - T (B2) ................................ ................................ ................................ .................. 7.8 7.2.2.4. LCD Inverter (C) ................................ ................................ ................................ ................................ .......................... 7.9 7.2.2.5. CPU Board (D) ................................ ................................ ................................ ................................ .......................... 7.10 7.2.2.6. LCD (E) + Touch Screen ................................ ................................ ................................ ................................ ........... 7.11 7.2.2.7. Headphone Jack (F) ................................ ................................ ................................ ................................ ................... 7.12 7.2.2 .8. Dual TGS Reader + USB port (G) ................................ ................................ ................................ ............................. 7 .13 7.2.2.9. iPod Docking Station (H) ................................ ................................ ................................ ................................ ........... 7.14 7.2.2.10. Ventilation duct frontal plug ................................ ................................ ................................ ................................ ...... 7.15 7.2.2.11. TGS + USB frontal plug ................................ ................................ ................................ ................................ ............ 7.16 7.3. A UDIO / V IDEO EXTERNAL CONNEC TORS B OARD ................................ ................................ ............................. 7.17 7.4. D ISASSEMBLING THE KEY BOARD / T OUCH S CREEN ................................ ................................ .......................... 7.18 7.4.1. LED Keyboard ................................ ................................ ................................ ................................ ... 7.18 7.4.2. VISIO Touch Screen ................................ ................................ ................................ .......................... 7.20 7.5. D ISASSEMBLING THE EME RGENCY BUTTON ................................ ................................ ................................ ...... 7.21 7.6. D ISASSEMBLING THE HS/HR CARDIO RECEIVER (C HEST B ELT / H AND S ENSOR ) ................................ .............. 7.22

9. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page v 9.1.16. Resetting parameters to default values ................................ ................................ ................................ 9.6 9.1.17. Format P&P key ................................ ................................ ................................ ................................ .. 9.6 9.1.1 8. User Detect ................................ ................................ ................................ ................................ .......... 9.7 9.1.19. Serial Number ................................ ................................ ................................ ................................ ...... 9.7 9.1.20. InMotion – (Ready to Run) ................................ ................................ ................................ .................. 9. 7 9.2. U SER MENU CONFIGURATI ON : 700/900 MODELS ................................ ................................ ................................ . 9.8 9.2.1. Language ................................ ................................ ................................ ................................ ............. 9.9 9.2.2. Distance ................................ ................................ ................................ ................................ ............... 9.9 9.2.3. Maximum exercise time ................................ ................................ ................................ ....................... 9.9 9.2.4. Pause time ................................ ................................ ................................ ................................ ........... 9.9 9.2.5. Cooldown time ................................ ................................ ................................ ................................ ... 9.10 9.2.6. Enable TGS ................................ ................................ ................................ ................................ ........ 9.10 9.2.7. Enable keyboard ................................ ................................ ................................ ................................ 9.10 9.2.8. Modifiabl e target heart rate ................................ ................................ ................................ .............. 9.11 9.2.9. Enable custom messages ................................ ................................ ................................ ................... 9.11 9.2.10. Edit messages ................................ ................................ ................................ ................................ .... 9.11 9.2.11. Change messagges languages ................................ ................................ ................................ ........... 9.11 9.2.12. Enable Up - Down motor ................................ ................................ ................................ .................... 9.12 9.2.13. Enable multi - language m ode ................................ ................................ ................................ ............. 9.12 9.2.14. Resetting parameters to default values ................................ ................................ .............................. 9.12 9.2.15. Format P&P ................................ ................................ ................................ ................................ ...... 9.12 9.2.16. User detect ................................ ................................ ................................ ................................ ......... 9.13 9.2.17. Serial Number ................................ ................................ ................................ ................................ .... 9.13 9.2.18. InMotion – (Ready to Run) ................................ ................................ ................................ ................ 9.13 9.3. S ERVICE MENU CONFIGUR ATION : LED MODELS ................................ ................................ ............................... 9.14 9.3.1. Accessing configuration of 500 models ................................ ................................ ............................. 9.14 9.3.2. Accessing configuration of 700 and 900 models ................................ ................................ ............... 9.14 9.3.3. Low kit parameter ................................ ................................ ................................ .............................. 9.16 9.3.3.1. Read from lo w kit ................................ ................................ ................................ ................................ ...................... 9.16 9.3.3.2. Write to low kit ................................ ................................ ................................ ................................ .......................... 9.16 9.3.3.3. Default Setting ................................ ................................ ................................ ................................ ........................... 9.17 9.3.3.4. Table of configuration parameters (LED): ................................ ................................ ................................ ................. 9.17 9.3.4. UpDown settings ................................ ................................ ................................ ............................... 9.18 9.3.4.1. Read from low kit ................................ ................................ ................................ ................................ ...................... 9.18 9.3.4.2. Write to low kit ................................ ................................ ................................ ................................ .......................... 9.18 9.3.4.3. Default setting ................................ ................................ ................................ ................................ ............................ 9.19 9.3.5. O perating data ................................ ................................ ................................ ................................ .. 9.19 9.3.5.1. Read from low kit ................................ ................................ ................................ ................................ ...................... 9.20 9.3.5.2. Write to low kit ................................ ................................ ................................ ................................ .......................... 9.20 9.3.5.3. Machine usage data ................................ ................................ ................................ ................................ .................... 9.20 9.3.6. Errors log ................................ ................................ ................................ ................................ .......... 9.21 9.3.6.1. Read from low kit ................................ ................................ ................................ ................................ ...................... 9.21 9.3.6.2. Reset Errors ................................ ................................ ................................ ................................ ................................ 9.21 9.3.6.3. COM.Fault ................................ ................................ ................................ ................................ ................................ . 9.22 9.3.6.4. View Errors ................................ ................................ ................................ ................................ ................................ 9.22 9.3.7. Standard settings ................................ ................................ ................................ ............................... 9.22 9.3.8. Low kit menu ................................ ................................ ................................ ................................ ..... 9.23 9.3.8.1. Low kit v ersion ................................ ................................ ................................ ................................ .......................... 9.23 9.3.8.2. Config. registers ................................ ................................ ................................ ................................ ......................... 9.24 9.3.9. High kit version ................................ ................................ ................................ ................................ . 9.25 9.3.10. BOOT version ................................ ................................ ................................ ................................ .... 9.25 9.3.11. Key Reader Version ................................ ................................ ................................ ........................... 9.25 9.3.12. Mains voltage ................................ ................................ ................................ ................................ .... 9.25 9.4. CONFIG.: VISIO - V ISIO WEB USER MENÙ ................................ ................................ ................................ ... 9.26 9.5. SERVICE MENU CONFIG.: VISIO - VISIOWEB ................................ ................................ ......................... 9.27 9.5 .1.1. Table of configuration parameters (VISIO): ................................ ................................ ................................ ............... 9.28 9.5.2. Register Addr. ................................ ................................ ................................ ................................ .... 9.29 9.5.2.1. Read from low kit ................................ ................................ ................................ ................................ ...................... 9.29 9.5.2.2. Register Value ................................ ................................ ................................ ................................ ............................ 9.29 9.5.2.3. Write to low kit. ................................ ................................ ................................ ................................ ......................... 9.29 9.5.3. Inverter pa rameters ................................ ................................ ................................ ........................... 9.30 10. AGGIORNAMENTO DEL SW ................................ ................................ ................................ ............................ 10.1

31. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.19 CU242: Connecting cable ALE Driver and LED Display (ALE Driver – LED Display ) ALE Driver J3A Signal Colour LED Display Patch Conn. A CN2 CN7 CN6 1 485 TXD+ RXD+ Brown / White 7 - - - 2 GND +12Vdc Grey - 2 - - 3 GND +5Vdc Black - 3 - - 4 n.c. - - - - - 5 485 TXD - RXD - Brown 8 - - - 6 +12Vdc Orange - 6 - - 7 +5Vdc Red - 7 - - 8 n.c. - - - - - 9 EXT Emergency White - - 4 - 10 Emergenc y restoration Blu e - - 5 - 11 n.c. - - - - - 12 n.c. - - - - - - HW Emergency Grey - - 2 3 - SW Emergency Grey - - 3 1 - GND +12Vdc ISO Black - - 6 2 Receiver HD1 Signal Colour FRAME Fast - on GND Yellow / Green Fast - on

35. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.23 CU337: LCD Power Supply (VISIO only) ( CPU Board – LCD) CPU Board CN2 Signal Colour LCD 1 Vcc LCD 5 2 Vcc LCD 6 3 Vcc LCD 11 7 Shield 17 8 RxE3+ 20 9 RxE3 - 22 10 RxEc+ 26 11 ExEc - 28 12 RxE2+ 14 13 RxE2 - 16 14 GND 23 15 RxE1+ 8 16 RxE1 - 10 17 GND 24 18 RxE0+ 2 19 RxE0 - 4 20 Rx03+ 19 21 Rx03 - 21 22 Rx0c+ 25 13 Rx0c - 27 24 GND 29 25 Rx02+ 13 26 Rx02 - 15 27 Rx01+ 7 28 Rx01 - 9 29 Rx00+ 1 30 Rx00 - 3 CU348: Ready to Run cable (“InMotion”) (VISIO only) ( InMotion Board – CPU Board ) InMotion Board S ignal Colo u r CPU Board : CN34 1 Vcc +5Vdc Brown 1 2 Em. Ligth Green 2 3 GND +5Vdc White 4

33. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.21 CU246: Antenna cable+ LAN (VISIO only) (CPU Board – Front lower frame) CPU Board : CN4 Signal Colour Anterior lower frame 1 LAN Signal White / Green 1 2 LAN Signal Green 2 3 LAN Signal White / Orange 3 4 LAN Signal Blue 4 5 LAN Signal White/Blue 5 6 LAN Signal Orange 6 7 LAN Signal Whi te / Brown 7 8 LAN Signal Brown 8 TUNER Board J6 Signal Colour Anterior lower frame 1 Antenna signal Black 1 CU307: Fan ON/OFF cable (ARM/CPU Board – Fan Micro - switch ) ARM Board : CN12 CPU Boa rd : CN33 Fan cable Signal Colour Fan micro - switch 2 - GND +12V - Fast - on 1 1 +12V Red - - 2 GND +12V - Fast - on CU308: User USB port cable (VISIO only) (CPU Board – USB Port) CPU Board CN14 Signal Colour USB Port 1 +5Vdc Red 1 2 USB - White 2 3 USB+ B lack 3 4 GND Green 4 5 Shield Blue 5 CU318: Signal cable (VISIO only) (Power Supply – Driver) Patch conn. 2 Signal Colour Driver J1 Power Supply 1 PHASE Brown - Socket 1 - 2 NEUTRAL blue - Socket 2 - Patch conn.2 Signal Colour Frame Fast - o n GND Yellow / Green Fast - on - Fast - on GND Yellow / Green - eyelet

36. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.24 CU375: AUDIO / VIDEO signal cable (VISIO only) (CPU Board – AUDIO / VIDEO Connectors Board) CPU Board : CN27 Signal Colour AUDIO / VIDEO Connector Board 1 n. c. - 1 2 In L White 2 3 GND in L Sheath 3 4 In R Red 4 5 GND in R Sheath 5 6 In VIDEO Yellow 6 7 GND in VIDEO Sheath 7 8 n. c. - 8 CU376: USB / C - Safe Connectors Board ca ble (VISIO only) (CPU Board – USB / C - Safe Connectors Board) CPU Board : CN6 Si gnal Colour USB / C - Safe Connectors Board 1 Vcc Oragne 1 2 Vcc Oragne 2 3 USB - White 3 4 USB + Brown 4 5 GND Shield Black 5 6 GND Black 6 7 GND Nero 7 8 Af_+bvdc_csafe Blue 8 9 Af_+bvdc_csafe Blue 9 10 Rxd1_in Red 10 11 Rxd1_in Yellow 11 12 Ct s1_in Gray 12 13 GND Black 13 14 GND Black 14 CU377: Emergency cable (ARM / CPU Board – Micro 1 (Hardware)/ Micro 2 (Software) CPU Board : CN22 Signal Colour Micro 1 (HW) Micro 2 (SW) ARM Board : Patch Conn. A 1 SW Emergency White CN02 - 2 GND_DIG Brown - CN05 3 HW Emergency Green CN02 - - GND Black CN03 CN04

34. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.22 CU331: iPod signal cable (VISIO only) (CPU Board – Docking Station) CPU Board CN26 Signal Colo u r Docking Station 1 +V bus USB Black 14 2 GND bus USB Black 13 3 TX - RX Black 11 4 RX – TX Black 12 5 CTS Black 10 6 +5Vdc Black 9 7 GND Black 8 8 GND Black 7 9 V ideo Gnd Black 6 10 V ideo signal Black 5 11 A udio L gnd Black 4 12 A udio L signal Black 3 13 A udio R signal Black 2 14 A udio R gnd Black 1 CU333: Headphone Jack cable (VISIO only) (CPU Board – Headphone Jack) CPU Board J5 Signal Colour Headphone Jack 2 Out_R Green 4 4 Schield Yellow 5 1 GND Red 2 3 Out_L Black 1 CU336: LCD Inverter Frontek cable (VISIO only) (CPU Board – LCD Inverter) CPU Board CN1 Signal Colour LCD Inverter CN1 1 +12Vdc entry Power Supply Black 11 2 ( * ) GND Black 1 3 ON - OFF Black 4 4 GND Black 3 5 ( * ) +12Vdc Black 12 6 Save - lamp Black 2 7 n.c. Black - ( * ) =Apply two wires on the same contact.

37. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.25 CU378: Connecting cable VISIO Display and ALE Driver (CPU Board – ALE Driver ) CPU Board CN17 Signal Colour ALE Driver J3A External Power Supply 1 n.c - - - 2 GND +12Vdc Grey 2 - 3 n.c. - - - 4 EXT Emergency White 9 - 5 GND +12Vdc EST Power Supply Black - 1 6 485 TXD – RXD - White 5 - 7 +12Vdc Orange 6 - 8 n.c. - - - 9 +12Vdc EST Power Supply Red - 2 10 Restore Blue 10 - 11 n.c. - - - 12 485 TXD + RXD + Brown 1 - Display Ground JP10 Signal Colour Receiver Ground HD1 Frame Ground Fast - on GND Giallo/Verde Fast - on Fast - on CU379: Connecting cable VISIO Display and AT - UL Driver (CPU Board – AT - UL Driver) CPU Board CN17 Signal Colour AT - UL Driver External Power Supply J3 J4 1 n.c. - - - - 2 GND +12V Grey 2 - - 3 n.c. - - - - 4 EXT Emergency White 9 - - 5 GND +12V EST Black - - 1 6 485 TXD – RXD - Brown - 8 - 7 +12V Orange 6 - - 8 n.c. - - - - 9 +12 EST Red - - 2 10 Restoring Blue 10 - - 11 n.c. - - - - 12 485 TXD + RXD + White / Brown - 7 - Display Ground JP10 Signal Colour Receiver Ground HD1 Frame Ground Fast - on GND Giallo/Verde Fast - on Fast - on

32. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Page 2.20 CU243: Connecting cable AT - UL Driver and LED Display (AT - UL Driver – ARM Board ) AT - UL CN01 AT - UL CN08 Signal Colour ARM Board Patch Conn. A CN2 CN7 CN6 2 - GND +12Vdc Grey - 2 - - 3 - GND +5Vdc Black - 3 - - 4 - sensing +5Vdc Brown - 4 - - 6 - +12Vdc Orange - 6 - - 7 - + 5Vdc Red - 7 - - 8 - + sensing 5Vdc Yellow - 8 - - 9 - EXT Emergency White - - 4 - 10 - Emergency restoration Blu e - - 5 - 11 6 - +12Vdc Orange - - - - 12 4 - - sensing +5Vdc Brown - - - - - 1 NC Green / White 1 - - - - 2 NC Green 2 - - - - 4 Downlo ad Blu 4 - - - - 5 Reset Blu e / White 5 - - - - 6 GND Digital Orange 6 - - - - 7 485 TXD+ RXD+ Brown / White 7 - - - - 8 485 TXD - RXD - Brown 8 - - - - - HW Emergency Grey - - 2 3 - - SW Emergency Grey - - 3 1 - - GND +12Vdc ISO Black - - 6 2 Receiv er HD1 Signal Colour FRAME Fast - on GND Yellow / Green Fast - on CU244: Cardio receiver cable (ARM/CPU Board – Receiver Board ) ARM Board : CN10 CPU Board : CN25 Signal Colour Cardio Receiver Board 4 n.c. 3 Pulse Signal White 5 2 +5V cardio.2 Brown 1 1 GND - Card Green 6

206. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.32 MENU – F – Par. Address Description Value Par. Address Description Value F - 0 300 Mo torpot ref 0 F - 110 321 Frequency ref 10 0 F - 10 301 Acc/Dec time mp 50 F - 111 322 Frequency ref 11 0 F - 11 302 Motorpot offset 0 F - 112 323 Frequency ref 12 0 F - 12 303 Mp output mode 0 F - 113 324 Frequency ref 13 0 F - 13 304 Mp auto save 1 F - 114 325 Frequenc y ref 14 0 F - 20 305 Max ref freq 1150 F - 115 326 Frequency ref 15 0 F - 21 306 Min ref freq 0 F - 116 327 Jog frequency 10 F - 50 307 Ref 1 channel 8 F - 200 328 Ramp resolution 0 F - 51 308 Ref 2 channel 0 F - 201 329 Acc time 1 3000 F - 60 309 MltFrq channel 1 3 F - 202 330 Dec time 1 3000 F - 61 310 MltFrq channel 2 3 F - 203 331 Acc time 2 50 F - 100 311 Frequency ref 0 0 F - 204 332 Dec time 2 50 F - 101 312 Frequency ref 1 0 F - 205 333 Acc time 3 50 F - 102 313 Frequency ref 2 0 F - 206 334 Dec time 3 / FS 50 F - 103 314 Fre quency ref 3 0 F - 207 335 Acc time 4 / Jog 50 F - 104 315 Frequency ref 4 0 F - 208 336 Dec time 4 / Jog 50 F - 105 316 Frequency ref 5 0 F - 250 337 Ramp S - shape 0 F - 106 317 Frequency ref 6 0 F - 260 338 Ramp extens src 0 F - 107 318 Frequency ref 7 0 F - 270 339 Ju mp amplitude 0 F - 108 319 Frequency ref 8 0 F - 271 340 Jump frequency 1 0 F - 109 320 Frequency ref 9 0 F - 272 341 Jump frequency 2 0 Table 9 - 4

204. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.30 9.5.3. I NVERTER PARAMETERS MENU – A – Par. Address Description Value Par. Address Description Value A - 0 1200 PID mode (700/900) 1 A - 59 1218 PID min neg err 50 PID mode (500) 0 A - 100 1219 Set Linear spe ed 0 A - 1 1201 PID ref sel 5 A - 101 1220 Set Acc Dec 100 A - 2 1202 PID fbk sel 4 A - 102 1221 Set Incline ref 0 A - 3 1203 PID digital ref 0 A - 105 1222 Def Linear speed 8 A - 4 1204 PID activat mode 0 A - 106 1223 Def Acc Dec 100 A - 5 1205 PID - Encoder sync 1 A - 10 7 1224 Def Incline ref 0 A - 6 1206 PID err sign rev 0 A - 110 1225 Pulley Ratio 200 A - 7 1207 PID Integ init en 0 A - 111 1226 Roller Diameter 91 A - 8 1208 PID update time 0 A - 115 1227 DCMot EncTimeout 250 A - 50 1209 PID Prop gain 1 7 DCMot EncTimeout 15 A - 51 1210 PID Int tconst 1 150 A - 116 1228 Fan command dly 3 A - 52 1211 PID Deriv gain 1 0 A - 117 1229 ACMot EncToller 50 A - 53 1212 PID Prop gain 2 0 0(OFF) A - 54 1213 PID Int tconst 2 9999 A - 118 1230 Check RunnerBand 10 A - 55 1214 PID Deriv gain 2 0 A - 119 1231 Check RunnerSpd 50 A - 56 1215 PID high limit 80 A - 120 1232 Curr clamp thr 200 A - 57 1216 PID low limit - 80 A - 121 1233 Check RunnerDly 60 A - 58 1217 PID max pos err 50 Table 9 - 1 MENU – C – Par. Ad dress Description Value Par. Address Description Value C - 0 800 Save parameters 0 C - 41 805 Save pars to key 0 C - 1 801 Recall param 0 C - 100 806 Measure stator R 0 C - 2 802 Load default 0 C - 200 807 Reset AC Flag 0 C - 20 803 Alarm clear 0 C - 201 808 Reset DC Flag 0 C - 40 804 Recall key prog 0 Table 9 - 2

205. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.31 MENU – D – Par. Address Description Value Par. Address Description Value D - 0 1 Output frequency 0 D - 200 26 An in 1 cnf mon 0 D - 1 2 Frequency ref 0 D - 201 27 An in 1 monitor 0 D - 2 3 Output current 0 D - 202 28 An in 1 term mon 0 D - 3 4 Output voltage 0 D - 210 29 An in 2 cnf mon 0 D - 4 5 DC link voltage 400 D - 211 30 An in 2 monitor 0 D - 5 6 Power factor 100 D - 212 31 An in 2 term mon 0 D - 6 7 Power [kW] 0 D - 220 32 An in 3 cnf mon 0 D - 7 8 Output speed 0 D - 221 33 An in 3 monitor 0 D - 8 9 Speed ref 0 D - 222 34 An in 3 term mon 0 D - 20 57 Actual speed 0 D - 300 35 EncPulse/Sample 0 D - 21 58 Actual incline user 0 D - 301 36 Encoder freq 0 D - 22 59 Actual ENC1 pos 0 D - 302 37 Encoder speed 0 D - 23 60 Crossed distance 0 D - 350 38 Option 1 state 0 D - 24 61 Reserved - D - 351 39 Option 2 state 0 D - 25 62 Flag status 0 D - 352 40 Par port state 0 D - 26 63 Actual ENC2 pos 0 D - 400 41 PID reference 0 D - 27 64 Actual speed from Fenc 0 D - 401 42 PID feedback 0 D - 30 70 Reserved - D - 402 43 PID error 0 D - 50 10 Heatsink temp 0 D - 403 44 PID integr comp 0 D - 51 11 Drive OL 0 D - 404 45 PID output 0 D - 52 12 Motor OL 0 D - 800 46 Error 1 0 D - 53 13 Brake res OL 0 D - 801 47 Error 2 0 D - 100 14 Dig inp status 0 D - 802 48 Error 3 0 D - 101 15 Term inp status 0 D - 803 49 Error 4 0 D - 102 16 Vir dig inp stat 0 D - 950 50 Drive rated cur 100 D - 120 17 Exp dig inp stat 0 D - 951 51 SW version 1 \ 2 200h D - 121 18 Exp term inp 0 D - 952 52 SW version 1 \ 2 80h D - 122 19 E xp Vir dig inp stat 0 D - 953 53 power ident code 0h D - 150 20 Dig out status 0 D - 954 54 param ident code 0h D - 151 21 Drv dig out sta 0 D - 955 55 regul ident code 3/8h D - 152 22 Vir dig out sta 0 D - 956 56 Startup id code 0h D - 170 23 Exp Dig out status 0 D - 9 57 71 Drive type 2 D - 171 24 Exp Drv dig out sta 0 D - 999 99 Display test - D - 172 25 Exp Vir dig out sta 0 Table 9 - 3

207. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.33 MENU – I – Par. Address Description Value Par. Address Descripti on Value I - 0 100 Dig input 1 cfg 1 I - 313 140 An out 2 filter 0 I - 1 101 Dig input 2 cfg 0 I - 350 141 Exp an out 1 cfg 0 I - 2 102 Dig input 3 cfg 0 I - 351 142 Exp AnOut 1 offs 0 I - 3 103 Dig input 4 cfg 0 I - 352 143 Exp AnOut 1 gain 100 I - 4 104 Dig input 5 c fg 0 I - 353 144 Exp AnOut 1 filt 0 I - 5 105 Dig input 6 cfg 0 I - 400 145 Inp by serial en 0 I - 6 106 Dig input 7 cfg 0 I - 410 146 Exp in by ser en 0 I - 7 107 Dig input 8 cfg 0 I - 420 147 Out by serial en 0 I - 50 108 Exp dig in 1 cfg 0 I - 430 148 Exp OutBySer en 0 I - 51 109 Exp dig in 2 cfg 0 I - 450 149 An out by ser en 0 I - 52 110 Exp dig in 3 cfg 0 I - 500 150 Encoder enable 1 I - 53 111 Exp dig in 4 cfg 0 I - 501 151 Encoder ppr 720 I - 100 112 Dig output 1 cfg 48 I - 502 152 Enc channels cfg 1 I - 101 113 Dig output 2 cfg 48 I - 503 153 Enc spd mul fact 100 I - 102 114 Dig output 3 cfg 48 I - 504 154 Enc update time 0 I - 103 115 Dig output 4 cfg 48 I - 600 155 Serial link cfg 6 I - 150 116 Exp DigOut 1 cfg 48 I - 601 156 Serial link bps 4 I - 151 117 Exp DigOut 2 cfg 48 I - 602 157 Device address 1 I - 200 118 An in 1 Type 1 I - 603 158 Ser answer delay 1 I - 201 119 An in 1 offset 0 I - 604 159 Serial timeout 0 I - 202 120 An in 1 gain 100 I - 605 160 En timeout alm 1 I - 203 121 An in 1 minimum 0 I - 700 161 Option 1 type 0 I - 204 122 An in 1 filter 1 I - 701 162 Option 2 type 0 I - 210 123 An in 2 Type 1 I - 750 163 SBI address 3 I - 211 124 An in 2 offset 0 I - 751 164 CAN baudrate 0 I - 212 125 An in 2 gain 100 I - 752 165 SBI Profibus mod 2 I - 213 126 An in 2 minimum 0 I - 753 166 SBI CAN mode 0 I - 214 127 An in 2 filter 1 I - 760 167 SBI to Drv W 0 0 I - 220 128 An in 3 Type 1 I - 761 168 SBI to Drv W 1 0 I - 221 129 An in 3 offset 0 I - 762 169 SBI to Drv W 2 0 I - 222 130 An in 3 gain 100 I - 763 170 SBI to Drv W 3 0 I - 223 131 An in 3 minimum 0 I - 764 171 SBI to Drv W 4 0 I - 224 132 An in 3 filter 1 I - 765 172 SBI to Drv W 5 0 I - 300 133 Analog out 1 cfg 0 I - 770 173 Drv to SBI W 0 1 I - 301 134 An out 1 offset 0 I - 771 174 Drv to SBI W 1 2 I - 302 135 An out 1 gain 100 I - 772 175 Drv to SBI W 2 3 I - 303 136 An out 1 f ilter 0 I - 773 176 Drv to SBI W 3 4 I - 310 137 Analog out 2 cfg 2 I - 774 177 Drv to SBI W 4 5 I - 311 138 An out 2 offset 0 I - 775 178 Drv to SBI W 5 6 I - 312 139 An out 2 gain 100 Table 9 - 5

208. RUN NOW Excite +: Service & maintenance manual - rev. 4.1 Pagina 9.34 MENU – P – Par . Address Description Value Par. Address Description Value P - 0 400 Cmd source sel 3 P - 281 446 Brake res value 150 P - 1 401 RUN input config 0 P - 282 447 Brake res power 5 P - 2 402 Reversal enable 1 P - 283 448 Br res thermal K 160 P - 3 403 Safety 1 P - 300 449 DC braking level 0 P - 20 404 Mains voltage 220 P - 301 450 DCB lev fac src 0 P - 21 405 Mains frequency 60 P - 302 451 DC braking freq 0 P - 40 406 Motor rated curr 70 P - 303 452 DC braking start 0 P - 41 407 Motor pole pairs 2 P - 304 453 DC braking stop 0 P - 42 4 08 Motor power fact 78 P - 320 454 Autocapture mode 0 P - 43 409 Motor stator R 100 P - 321 456 Autocapture Ilim 120 P - 44 410 Motor cooling 1 P - 322 457 Demagnetiz time 8 P - 45 411 Motor thermal K 30 P - 323 458 Autocap f scan 10 P - 60 412 V/f shape 1 P - 324 459 A utocap V scan 2 P - 61 413 Max out voltage 230 P - 325 460 Enc for FlyRes 0 P - 62 414 Base frequency 600 P - 326 461 Fre for FlyRes 0 P - 63 415 V/f interm volt 115 P - 340 462 Undervoltage thr 50 P - 64 416 V/f interm freq 300 P - 341 463 Max pwrloss time 0 P - 80 41 7 Max output freq 100 P - 342 464 UV alarm storage 1 P - 81 418 Min output freq 0 P - 360 465 OV prevention 0 P - 100 419 Slip compensate 90 P - 380 466 Autoreset attmps 0 P - 101 420 Slip comp filter 3 P - 381 467 Autoreset clear 10 P - 120 421 Manual boost [%] 30 P - 382 468 Autoreset delay 50 P - 121 422 Boost factor src 0 P - 383 469 Autores flt rly 1 P - 122 423 Auto boost en 1 P - 400 470 Ext fault mode 0 P - 140 424 Magn curr gain 30 P - 420 471 Volt reduc mode 0 P - 160 425 Osc damping gain 10 P - 421 472 V reduction fact 10 0 P - 180 426 SW clamp enable 1 P - 422 473 V fact mult src 0 P - 200 427 Ramp CurLim mode 0 P - 440 474 Frequency thr 1 0 P - 201 428 Curr lim in ramp 170 P - 441 475 Freq prog 1 hyst 5 P - 202 429 En lim in steady 0 P - 442 476 Frequency thr 2 0 P - 203 430 Curr lim steady P - 443 477 Freq prog 2 hyst 5 P - 204 431 Curr ctrl P - gain P - 460 478 Const speed tol 5 P - 205 432 Curr ctrl I - gain P - 461 479 Const speed dl 1 P - 206 433 Curr ctr feedfwd P - 480 480 Heatsnk temp lev 70 P - 220 434 En DC link ctrl P - 481 481 Heatsnk t emp hys 5 P - 221 435 DC - lnk ctr Pgain P - 500 482 Switching freq 9 P - 222 436 DC - lnk ctr Igain P - 501 483 Sw freq reduc en 0 P - 223 437 DC - link ctr FF P - 520 484 Overmod max lev 0 P - 240 438 OverTorque mode P - 540 485 Out Vlt auto adj 0 P - 241 439 OT curr l im thr P - 560 486 Deadtime cmp lev 9 P - 242 440 OT level fac src P - 561 487 Deadtime cmp slp 50 P - 243 441 OT signal delay P - 580 488 Startup display 1 P - 260 444 Motor OL prot en P - 600 489 Speed dsply fact 100 P - 280 445 Brake res OL en P - 999 490 Param prot code 0 Table 9 - 6

Views

  • 423 Total Views
  • 280 Website Views
  • 143 Embeded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 2

  • 24 www.fitness-trader.com
  • 10 fitness-trader.odoo.com
You can compare max 4 products.