0 item

Technogym Wave Excite Class Trend Service Maintnance Manual

Public Channel / Manuals

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

2.

4.

213.

52.

1. S ERVICE & MAINTENANCE MANUAL R EV . 2.0

32. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.20 Page intentionally left blank

51. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.7 Page intentionally left blank

10. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.6 Page intentionally left blank

44. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.12 Page intentionally left blank

139. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.39 7.18. DISASSEMBLING THE CONNECTION BELT BETWEEN PRIMARY AN D SECONDARY SHAFT To disassemble the connection belt between the prim ary and secondary shaft, it needs to remove the primary shaft assembly and the secondary shaft assembly as detailed in paragraph 7.16. “ Disassembling the secondary shaft assembly” and 7.17. “ Disassembling the primary shaft assem bly

202. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.50 Page intentionally left blank

58. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 5.6 Page intentionally left blank

214. 0SM00386AA-IT TECHNOGYM S.p.A. Via G. Perticari, 20 47035 Gambettola (FC) ITALIA Tel.: +39-0547-650638 Fax: +39-0547-650150 e-mail: [email protected]

112. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.12 7.3.3. 700WTV VERSION (W ELLNESS TV) To disassemble the Touch Screen, please refer to the Display Board disassembly procedure: 7.2.3. “ 700WTV version (Wellness TV)”

50. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.6 LIBYA DVB-T -

144. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.44 Page intentionally left blank

3. The information contained in this manual is intended for QUALIFIED TECHNICIANS who have completed a specific TECHNOGYM training course a nd are authorized to perform machine start- up and adjustment procedures as well as extraordinary maintenance or repairs which require a thorough knowledge of the machine, its operation, its safety devices and working procedures. CAREFULLY READ THE INFORMATION CONTAINED IN THIS MANUAL BEFORE PERFORMING ANY MAINTENANCE PROCEDURES ON THE MACHINE DANGEROUS VOLTAGES PRESENT NOTE The information contained in this document is subject to change without notice. Technogym does not guarantee this documentation in any way. Technogym shall not be held responsible for any errors contained in this manual and declines all liability for accidents or damages resulting from the supply, characteristics or use of this manual. This document contains proprietary information that is protected by copyright. All rights reserved. No part of this document may be photocopied, re produced or translated into another language without the prior written consent of Technogym. The Technogym™ trademark is property of Technogym S.p.A. The Wave Excite™ trademark is property of Technogym S.p.A.

195. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.43 Press “YES” to save the changes permanently or “NO” to continue.

204. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 10.2 First of all, check the resistance on the tester probes is approximately 0 Ω .

131. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.31 Figure 7.14-4 To reassemble the spring and the cam, carry out the above steps in reverse order. The cams used on the two sides of the machine, are both the same part so check the proper point of connection for spring and belt.

201. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.49 Tap the centre of the + which appears on the screen, using an object that is pointed but not sharp. The procedure must be repeated three times, with the + appearing in three different positions. At the end, the message “Calibration successful” will appear if the procedure was correctly carried out, or “Calibration incomplete” if the procedure was not co mpleted properly, after which the machine reverts to standby mode. During the machine power-up sequence, wh ile the message showing the installed software version is scrolling, pressing any po int on the touch-screen for more than 6 seconds will automatically invoke the calibra tion procedure as soon as the software version display finishes. Upon exiting th e calibration procedure (successfully or unsuccessfully), the machine automatically reverts to the standby state.

100. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.42 Page intentionally left blank

48. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.4 4.4. MONITOR PLUG FOR CSAFE PORT When the plug code 0WC00639AA is fitted into any one of the CSafe ports on the machine, the corresponding LED should illuminate to indicate the presence of the 5 Vdc supply on the port. During the CSafe port test functi on, the plug connects the transmit channel directly to the receive channel, thereby producing a positive test outcome if the port is functioning correctly.

151. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.7 Figure 8.6-6 Figure 8.6-7 During reassembly procedure lock down the ba ll joints using a torque wrench setting of 22Nm/16.2ft.lbf, excepting the ones in Figure 8.6-4 and Figure 8.6-7, which need a tightening torque of 25Nm/18.4 ft.lbf. Refer to the Spare Parts Catalogue, as regards the codes of rods and levers.

200. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.48 At this point the following screenshot appears on the display:

211. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 12.1 12. APPENDIX 12.1. UPDATING THE SW To update the machine SW it is necessary to ch ange the contents of the FLASH EPROM on the 386 or ARM board by means of an external PC connect ed to the CSAFE port on the machine, situated on the lower part of the display panel. The PC can only update the FLASH EPROM during machine power up, before the self- test sequence begins. After the Display SW update it is necessary to restore all the parameters to the default values following the detailed instru ctions provided in paragraph: 9.2.13. “ Resetting parameters to default values”. After the lower electronic SW update it is n ecessary to restore all the parameters to the default values following the detailed instructions provided in paragraph: 9.5.1.3 “ Default Setting”.

80. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.22 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check that the antenna signal matches with the minimal requested specifications detailed at paragraph: 5.3. “ Recommended antenna signal requirement”. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version. The TV and RADIO channels is located in the Digital TV in the CPU Board and must necessarily be present. This means that when even one of the two boards will be replaced, should be re-stored channels thro ugh search or transferring from another machine via TGS key or cable transfer.

190. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.38 Press “YES” to save the changes permanently or “NO” to continue. It is possible to search TV channels on the digital or on the analogue band, by pressing on the proper buttons: or The default TV standard is the one set at paragraph : 9.5.6. “ TV Standard”, of the service menu. It is anyway possible to store channels transm itted with dif ferent TV standard, changing this parameter, using keys + and – , in the proper menu .

45. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.1 4. ACCESSORIES 4.1. CARDIO THEATER CONNECTION The machine can be connected to the CardioTheat er by means of the RJ45 connector on the CSafe board. The CardioTheater unit must be provided with a power cable having the following pin-out: RJ45 Connector Signal 5 +5 Vdc 7 Ground WARNING: for the numbering of the pins, on RJ45 connector, please refer to the diagram below:

148. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.4 8.4. ALIGN THE BELT CONNECTING THE PRIMARY AND SECONDARY SHAFTS Figure 8.4-1 Carry out the operations described in paragraph: 7.7. “ Disassembling the guards” for disassembling the front guard. 1. Check that the pulley on the prim ary shaft is aligned with the sprocket on the secondary shaft using a straight reference rod, and adjust the bridge bearings if needed, moving them sideways inside the slots on the frame.

46. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.2 4.2. PC LINK FOR PROGRAMMING The machine can be connected to a PC for programming by means of the RJ45 connector on the CSafe board. WARNING: for the numbering of the pins, on RJ45 connector, please refer to the diagram below: When programming the machine sometimes it is necessary to fit plug into the free RJ-45 port on the back of the display, to avoid any type of interference during the operation. The wiring diagram of the RJ-45 plug is as follows: Programming cable and plug can be ordered using the code R0002534AB .

71. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.13 2 Start exercising by choosing "Quick-Start" mode and press on the Touch- Sensors: Is the resistance change? Do y ou hear beep sound? NO Replace CPU board YES Replace the LCD inv erter. Does the problem persists? YES Replace LCD A NO Def ectiv e LCD inv eter Continued on the following page

121. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.21 7.10. DISASSEMBLING THE FOOTBOARDS Figure 7.10-1 1. Back off the 4 nuts (a) with a 10mm wrench. 2. Remove the footboard. To reassemble the footboards, carry out the above steps in reverse order.

199. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.47 9.9. TOUCH SCREEN CALIBRATION The machine configuration procedure is invoked, wh en the machine is in standby mode, by pressing the top right hand, the bottom left hand and the bottom right hand corner in sequence, as shown in the picture below. The machine display will shows a window from where you can access the different configuration menus, using the proper password. To access the menu, type in the password 2409 and press ENTER key to confirm or BACK key to back forward.

56. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 5.4 5.3.2. ANALOGUE SIGNAL ALL STANDARD Level Higher than -50 dBm (59 dBμV) (-1 dBmV) Quality S/N (Signal to Noise ratio) Higher than +50 dB WARNING: If the machine is not connected to a terrestrial antenna--or if it is but the antenna signal line is interrupted by devices such as TV distribution units, modulators, etc.--the machine will not be able to receive a usable antenna signal for radio channel tuning.

60. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.2 6.1. TROUBLESHOOTING SERVICE MENU: ACTIVE WELLNESS TV MODELS The machine configuration procedure is invoked, wh en the machine is in standby mode, by pressing the top right hand, the bottom left hand and the bottom right hand corner in sequence, as shown in the picture below. The machine display will shows a window from where you can access the different configuration menus, using the proper password. To access the menu, type in the password 2411 and press ENTER key to confirm or BACK key to back forward. At this point the machine disp lay will shows the different parameters of the menu. To exit the TROUBLESHOOTING menu press HOME key.

147. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.3 8.3. BRAKE WINDING POSITION Figure 8.3-1 Carry out the operations described in paragraph 7.7. “ Disassembling the guards”. 1. Back off the 2 screws (a) and position the brake winding support (b) so that it is centred on the copper disk, using a 1m m thickness gauge. 2. Lock the screws back down.

189. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.37 9.6. TV MENU CONFIGURATION FOR 700WTV MODELS 9.6.1. T UNING TV CHANNELS The machine configuration procedure is invoked, wh en the machine is in standby mode, by pressing the top right hand, the bottom left hand and the bottom right hand corner in sequence, as shown in the picture below. The machine display will shows a window from where you can access the different configuration menus, using the proper password. To access the menu, type in the password 2407 and press ENTER key to confirm or BACK key to back forward. At this point the partial screen TV is displaye d on the machine display, as shown in the picture below. To permanently save the changes which are goi ng to be made in this page, press “SAVE IN EEPROM” key. To go back to the home page press “HOME” key and the configuration will be available until the machin e is restarted. This is why the following confirmation message is displayed:

12. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 1.2 1.3. GENERAL RULES FOR REPAIR PROCEDURES 1. Always mark any parts or positions which may be confused with each other at the time of reassembly. 2. Use original Technogym spare parts and lubricants of the recommended brands. 3. Use special tools where specified. 4. Consult the Technical Newsletters, which ma y contain more up-to-date information on adjustments and maintenance than those contained in this manual. 5. Before starting the repair procedure, make sure that the recommended tools are available and in good condition. 6. For the procedures described in this manual, use only the specified tools. The tool sizes quoted in this manual are expressed in mm.

54. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 5.2 5.2. MOVING THE MACHINE You can move the machine using a dolly ( Figure 5.2-1) or an hand trolley ( Figure 5.2-2), following the indications reported in the picture below. Figure 5.2-1 Figure 5.2-2 WARNING: insert the base of the trolley between the casin g and the frame of the machine. Figure 5.2-3 WARNING: Do not tilt the machine pivoting it on the front side.

42. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.10 A higher brake excitation signal will produce a correspondingly higher exercise resistance. Due to the eddy currents, energy is dissipate d on the brake disk in the form of heat. During the movement, the speed sensor detects the heads of the brake disk fixing screws, and produces a speed feedback signal that is sent to the Brake board. The brake board will adjust s the excitation current of the brake winding so that the sp eed detected by the speed sensor is equal to the set value. The control is closed loop. If the brake board does not receive a speed signal, which indicates that an exercise session is in progress, the machine will not produce any resistance. During the movement, the brake board monitors for possible malfunctions. The errors which can occur are: Error Code Description 1 OVERHEATING: this condition occurs when the temperature detected by the sensor on the circuit board exceeds 90°C. 8 OVERVOLTAGE: this condition occurs when the +12 Vdc voltage goes above 13.7 Vdc (only on the 500, 700 and 700WTVmodels). In all the cases, the brake board interrupts the supply of current to the brake, the green LED changes from being steadily on to blinking and sends an error message to the display board which displays the “THE EQUIPMENT IS BLOCKED” message.

152. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.8 8.7. THE MACHINE IS NOT FLAT This problem may be due to the positioning of the machine on a not flat surface. To resolve this problem is necessary to act on foot adjustment. Figure 8.7-1 1. Screw the foot (a) in or out until the frame is in a stable position. 2. Adjustment made to tighten the counter-nut (b) .

16. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.4 2.4. MECHANICAL CHARACTERISTICS VERSION 500 – 700 - 700WTV 500SP – 700SP Width 800 mm – 32” Length 1600mm – 63” Height 1500mm – 59” Weight 130 Kg - 287 lbs

77. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.19 Replace the CU160 cable. Working? Replace the Digital TV board and / or the CPU board NO CU160 cable def ectiv e Check the conditions of antenna cable. It is CU-198 ok? Replace the CU-198 cable. NO A Is the TV standard correctly conf igured? Conf igure the "TV standard" parameter NO 2 YES 3 Check the Antenna signal. 4 YES YES YES YES

146. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.2 8.2. SPEED SENSOR POSITION Figure 8.2-1 Carry out the operations described in paragraph 7.7. “ Disassembling the guards”. 1. Back off the 2 screws (a) and shif t the speed sensor support to the side, so that it is 0.7mm from the screws on the copper disk. 2. Lock the screws back down.

194. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.42 9.7. RADIO MENU CONFIGURATION FOR 700WTV MODELS 9.7.1. T UNING RADIO CHANNELS The machine configuration procedure is invoked, wh en the machine is in standby mode, by pressing the top right hand, the bottom left hand and the bottom right hand corner in sequence, as shown in the picture below. The machine display will shows a window from where you can access the different configuration menus, using the proper password. To access the menu, type in the password 2408 and press ENTER key to confirm or BACK key to back forward. At this point the partial screen TV is displaye d on the machine display, as shown in the picture below. To permanently save the changes which are goi ng to be made in this page, press “SAVE IN EEPROM” key. To go back to the home page press “HOME” key and the configuration will be available until the machin e is restarted. This is why the following confirmation message is displayed:

164. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.12 9.2.14. F ORMAT P&P This function formats a TGS key for Plug&Play mode operation. To select the function, when the display shows: FORMAT P&P press ENTER to confirm, or cancel by pressing the CLEAR key for a few seconds. At the end of the configura tion procedure, hold down the CLEAR key for a few seconds to exit. The CLEAR key can be pressed at any time to interrupt the procedure and revert to standby mode. 9.2.15. SN This parameter shows the serial number of the machine. SN:xxxx

70. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.12 6.3.3. 700WTV W ELLNESS TV MODELS A Does the wall outlet supply the correct v oltage? Is the mains lead OK? Are the LED on the Display board lit on? Plug the machine into a working electrical outlet Replace the mains lead THE DISPLAY DOES NOT ILLUMINATE NO YES NO YES YES NO B 1 Are the f uses OK? Replace the f uses YES NO Continued on the following page

86. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.28 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Place the tester probes across pins 1-2 of the connector CN2 on the brake board and exercise at a speed of 60 RPM. You should measure a Vdc which increases according to the exercise level. (2) As for step (1) but across the two fast-on at the input of the brake. (3) As for step (1) but with everything reconnected, and across the brake winding. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

88. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.30 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Carry out the “Standard Setting” procedure as detailed at paragraph 9.5.5. “ Standard settings ”. (2) Check that the mechanical system, consisting of the pedals, belt and brake, moves smoothly and without higher than normal friction or resistance. (3) Measure the voltage supplied by the brake board to the winding. In “Quick Start” mode, select the effort level and check that the value is different from 0. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

136. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.36 Figure 7.16-5 To disassemble the copper disk: 13. Back off the 6 screws (f) using a 4mm hexagonal wrench. Take particular care with the copper disk, as it bends easily and may then cause problems after reassembly, by brushing against the winding block. During reassembly, lock down the screws “f” using a torque wrench setting of 6Nm. To reassemble the secondary shaft assembly, carry out the above steps in reverse order. After completing the reassembly, carry out the adjustment procedure described in paragraph 8.1. “ Belt tension” and 8.4. “ Align the belt connecting the primary and secondary shafts”.

59. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.1 6. TROUBLESHOOTING The troubleshooting procedures are illustrated by means of flow diagrams. To facilitate interpretation of these diagrams, the following standard box shapes are used: This type of box is the START point of the troubleshooting procedure. It typically contains a description of the problem or malfunction. This type of box represents a decision point in the troubleshooting procedure. It typically contains a description of the CHECK to be made, with an outcome that is either a positive (YES) or negative (NO) response. This type of box is a step in the troubleshooting procedure where an ACTION must be carried out. It typically contains a description of the ACTION necessary to resolve the problem Therefore, after executing the specified ACTION: 1. Check whether the problem has been resolved; 2. If the problem persists, it is recommended to resume the troubleshooting procedure from the point before the action was carried out. A circled number (such as that shown on the left) next to a box of the troubleshooting procedure indicates that more detailed instructions for performing that particular check or action are provided below the flowchart. A circled letter (such as that shown on the left) is used to mark a point in the procedure. Typically, this indicator is used in page changes. The connectors indicated in the following pages, refer to 700 model’s LED Boards, unless otherwise indicated.

165. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.13 9.3. USER MENU CONFIGURATION FOR 700 WTV MODELS The machine configuration procedure is invoked, wh en the machine is in standby mode, by pressing the top right hand, the bottom left hand and the bottom right hand corner in sequence, as shown in the picture below. The machine display will shows a window from where you can access the different configuration menus, using the proper password. To access the menu, type in the password 2406 and press ENTER key to confirm or BACK key to back forward. At this point the machine display will shows the different parameters of the menu, collected in different pages, which can be scrolled with the FORWARD and BACK keys. To exit the configuration press HOME key. Pressing “HOME” in any page, all changes made up to that moment are saved; you cannot exit without saving. In case of erro rs the initial Technogym settings can be restored using the “DEFAULT CONFIG.” parameter.

62. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.4 6.1.4. TGS COM T EST The test checks the communication with the TGS reader. The test can have two outcomes: • “Test Successful”: This means that the test was completed successfully, i.e. that serial communications on the selected port are correct. • “Error COM3”: This means that the outcome of the test was negative. The “TGS COM test” done on machine not provided with the key reader gives a fail outcome. 6.1.5. DVT B OARD TEST It’s a command that allows to divert the seri al communication, usually between the Digital TV boardand the CPU board, on the external CSafe port. This function wich allows to connect an external device to the Digital TV board is not used at the moment. Once the function has been launched it is n ecessary to switch off and switch on again the machine to reinstate the correct connection.

210. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 11.4 11.3.8. C HECKING THE WIRING AND CONNECTIONS 1. Check the condition of all the cables: • External conditions; • Possible rusting of the connectors; • Electrical continuity of the individual wires; • Isolation of the individual wires toward ground. Repair and/or replace any non-conforming wires. 2. Check the condition of the fuses using a tester.

40. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.8 3.1.12. A LTERNATOR Only for self-power versions: 500SP and 700SP. The alternator consists of a stator winding whose rotor is put into rotation by the movement of the pedals, generating the voltage necessary for the machine’s operation. Depending on the rate of pedaling and the resulting speed of rotation, it generates an alternating voltage which ranges from approximately 15- 17 VAC at about 30-35 RPM to over 40 VAC for higher pedaling speeds. The alternator has a built-in speed sensor which provides to the brake board the speed signal. 3.1.13. B ATTERY Only for self-power versions: 500SP and 700SP. This is a 12 V – 4.5 AH battery which, in the self -powered version, supplies the machine whenever the alternator is unable to produce a sufficient voltage for powering the machine, and for at least 30 seconds after the user has stopped pedaling to allow data to be saved in memory. The battery can be recharged in 2 ways: • during the exercise, through the brake board; • in the standby condition, from an external power supply included with the machine, which is able to fully recharge the battery in 8 hours. Do not use the machine during recharging with the external power supply. 3.1.14. E XTERNAL POWER SUPPLY INPUT Only for 700i SP versions. This is a socket for plugging in the external power supply that comes with the machine, which can be used to recharge the battery. It is situated on the side of the front platform.

78. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.20 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check that the antenna cable is correctly connected to the TUNER on Digital TV board. (2) Carry out the configuration procedure as detailed at paragraph 9.5.6. “ TV Standard”. (3) Check that the antenna signal matches with the minimal requested specifications detailed at paragraph: 5.3. “ Recommended antenna signal requirement”. (4) Check the state of wear of the antenna cable, and that it properly works. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version. The TV and RADIO channels is located in the Digital TV in the CPU Board and must necessarily be present. This means that when even one of the two boards will be replaced, should be re-stored channels thro ugh search or transferring from another machine via TGS key or cable transfer.

95. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.37 6.14.2. H AND S ENSOR The machine displays this error if the HS/HR recei ver is not working, or if it is not supplied by the display board. For an easier and quicker diagnosis of the problem, we recommend to use the functions of Test Box Excite. THERE I S NO HR SIGNAL Are the sensors correctly connected to the HS/HR receiv er? Is the v oltage at the output of the display board correct ? Reinstate the connection. Replace cable CU223. Replace the display board. 2 4 YES NO YES NO Is the v oltage at the input to the HS/HR receiv er correct? Replace the HS/HR receiv er. 3 YES NO Verif y the wiring and earth connection of the machine. 1

143. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.43 7.22. SMONTAGGIO BATTERIA Figure 7.22-1 Carry out the operations described in paragraph 7.7. “ Disassembling the guards ” . 1. Rem ove the 2 cable ties (a) . 2. Unplug the 2 fastons (b) and remove the battery, replace if is necessary. To reassemble the battery carry out the above steps in reverse order.

150. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.6 8.6. TIE ROD LENGTH Adjust the length of the tie rods according to the data, for each of them, in the following figures. Figure 8.6-1 Figure 8.6-2 Figure 8.6-3 Figure 8.6-4 Figure 8.6-5 Continued on following page →

47. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.3 4.3. CABLE FOR EXCHANGING TV CHANNEL TUNING DATA BETWEEN TWO MACHINES The link for transferring the TV channel tuning data from one machine to the other is effected via a special cable, which plugs into the RJ45 connectors of the CSafe boards. The cable to use (code 0WC00644AA ) must be wired as follows: Cable CSafe Periferic CSafe Board; RJ45 Signal Colour CSafe Board; RJ45 3 Tx White 4 4 Rx Brown 3 7 Digital Ground Green 7 8 Ground Shield Yellow 8 WARNING: for the numbering of the pins, on RJ45 connector, please refer to the diagram below:

79. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.21 6.7. THE RADIO DOES NOT PLAY With the ANALOGIC signal, the radio signal can only be acquired from an aerial antenna signal. If the machine is connected to a digital source (or to a satellite antenna) it will be impossible to use the radio function. If ACTIVE Wellness TV interface is in stalled, check that the parameter: 9.3.17. “ Radio” is correctly set. It is now possible only the tuning of the digital band and not more the analogue one. 1 Is the TV channel sound OK? Replace the CPU board. Does it work correctly ? Perf orm the "Audio does not work" procedure Def ectiv e CPU board NO YES THE RADIO DOES NOT PLAY YES Check if the antenna signal is good NO Is the tuner connected to a terrestrial antenna cable without any ty pe of interruption (multiplexer, TV distribution module)? Connect a signal that meets these requirements NO YES

97. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.39 6.15. THE TELEMETRIC HEART RATE SIGNAL IS INCORRECT The machine displays this error if the receiver is disturbed by sources of electromagnetic noise. THE TELEMETRIC HR SIGNAL IS INCORRECT Are the machines correctly spaced by the required minimum distance? Is the receiv er correctly positioned and are the connecting cables properly routed? Are there sources of electromagnetic noise near the receiv er? Reposition the machines so they are adequately spaced Correct the position of the receiv er and the routing of the cables Mov e the machine away f rom the noise source or attenuate the power of the noise NO YES NO YES NO YES 4 A Check the earth connection of the machine 1 3 2 Continued on the following page

128. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.28 Figure 7.13-3 Be carefully to reinsert the plastic spacer (c) on the ball joints, in the same position. Figure 7.13-4 5. Back off the fixing lever screw, using a ratchet wrench and a 17mm socket wrench and remove the two washers, as shown in the figure at the side. During the reassembly, lock down the screws using a torque wrench setting of 15Nm/11.1ft.lbf. Figure 7.13-5 6. Remove the lever (d) from the pin on the frame, highlighted in the figure. Continued on following page →

41. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.9 3.2. BRAKE CONTROL 3.2.1. M ECHANICS The motion of the pedals imparts a rotation to the primary shaft via the belts connected to the 2 pedals. The primary shaft is connected to the sec ondary shaft and so to the brake, by means of a belt. The speed sensor attached to the frame detects the heads of the screws which secure the disk to the flywheel, and generates a signal proportional to the speed. 3.2.2. C ONTROLS The control block diagram is as follows: To obtain a given exercise effort level, the display board sends the required value of exercise speed in step per minute to the Brake board via the RS-485 serial link. Based on the commands received the brake board will then apply the appropriate excitation current to the brake winding, which generates an electromagnetic field. When the brake interface board receives the signal to generate resistance, the green LED illuminates. The electromagnetic field produced by the winding and the rotation of th e disk will induce eddy currents in the disk itself, giving rise to a force that tends to brake its motion. This generates the exercise resistance. Display Board Brake board RS-485 CN9 CN4 1-2/CN2 Brake Excitation Current 3-4/CN2 Pulses Speed sensor Green LED

84. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.26 6.9. “THE EQUIPMENT IS BLOCKED (COM)” MESSAGE ON DISPLAY This error message can be caused by loss of communication between the lower and upper assemblies. The error is displayed by a massage and stored in the “ Errors Log ” section. To reinstate communications between the lower and upper assemblies: (1) Check that cables CU69 and CU63 are correct, using the Test Box Excite and replace if necessary; (2) Try replacing the brake board and the displa y board in turn, and check whether the communication works. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

129. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.29 Figure 7.13-6 To reassembly the lever, carry out the above steps in reverse order. ATTENTION: To easily reassembly the lever, avoiding to damage the internal bearings use the special pin (0T020901AA). 7. Screw completely in the special tool (e) on the pin frame (f) . Figure 7.13-7 8. Insert the lever (d) on the pin (e) , moving slowly and paying particular attention to the internal bearings of the lever. During the reassembly, check the length of the tie rods, as detailed at the paragraph: 8.6. “ Tie rod length”, if they had been removed.

145. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.1 8. ADJUSTMENTS 8.1. BELT TENSION Figure 8.1-1 Carry out the operations described in paragraph 7.7. “ Disassembling the guards” for removing the front guard. 1. Back off the screws (a) and adjust the tension of the belt by acting on the screw (b) . The correct belt tension is 190 Hz. If a new belt is used, after having tensioned it according the above procedure, it is recommended to exercise for a minute , in order to “pull” the belt. Then check again the tension value. 2. At the end of the tensioning procedure, remember to lock the screws (a) back down.

182. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.30 9.5. SERVICE MENU CONFIGURATION 700 WTV MODELS The machine configuration procedure is invoked, wh en the machine is in standby mode, by pressing the top right hand, the bottom left hand and the bottom right hand corner in sequence, as shown in the picture below. The machine display will shows a window from where you can access the different configuration menus, using the proper password. To access the menu, type in the password 2501 and press ENTER key to confirm or BACK key to back forward. At this point the machine display will shows the different parameters of the menu, collected in different pages, which can be scrolled with the FORWARD and BACK keys. To exit the configuration press HOME key. Pressing “HOME” in any page, all changes made up to that moment are saved; you cannot exit without saving. In case of erro rs the initial Technogym settings can be restored using the “STANDARD SETTINGS.” parameter.

11. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.1 1. GENERAL NOTICES 1.1. INTRODUCTION This document is reserved for Technogym Servi ce technicians, and is intended to provide authorized personnel with the necessary information to correctly carry out repairs and maintenance. A thorough knowledge of the technical information contained in this manual is essential for completing the professional training of the operator. In order to facilitate consultation, the paragra phs are accompanied by schematic drawings which illustrate the procedure being described. This manual contains notices and symbols which have a specific meanings: WARNING: non observance may result in accident or injury. ATTENTION: non observance may cause damage to the machine. Information about the operation in progress. Observation about the operation in progress. 1.2. RECOMMENDATIONS Technogym recommends the following steps for planning repair procedures: • Carefully evaluate the customer’s descripti on of the machine malfunction and ask all the necessary questions to clarify the symptoms of the problem. • Clearly diagnose the causes of the problem. This manual provides the fundamental theoretical basis, which must then be integrated by pe rsonal experience and attendance at the training courses periodically offered by Technogym. • Rationally plan the repair procedure so as to minimize the downtime necessary for procuring spare parts, preparing tools, etc. • Access the component to be repaired, avoiding any unnecessary operations. In this regard it will be useful to refer to the disassembly sequence described in this manual.

66. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.8 6.3. THE DISPLAY FAILS TO ILLUMINATE This error occurs when the power supply voltage is not reaching the upper assembly. 6.3.1. 500 AND 700 M ODELS Does t he wall out let supply t he correct voltage? I s t he mains lead O K? Are t he LEDs on t he Display board lit on? Plug t he machine int o a working elect rical out let Replace t he mains lead Replace t he Display board TH E D I SPL AY DOES NOT ILLUMINATE NO YE S NO YE S NO YE S A 1 Are t he f uses O K? Replace t he f uses YE S NO Continued on the following page

173. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.21 TECHNICAL CONFIGURATION OPERATING DATA LOW KIT MENU LOW KIT PARAM. HIGH KIT VERSION STANDARD SETTINGS ERRORS LOG KEY READER VERS. To scroll through the list of parameters, press the + or – effort level keys to display the next or the preceding item. To modify a parameter value, it is necessary to press the ENTER key: when the current parameter value starts to blink, press the CLEAR key to erase the current value and then use the number keys to enter the desired new value. Save the changes made by pressing the ENTER key. To cancel the operation, press the CLEAR key for a few seconds. The various parameters are described below.

193. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.41 9.6.2. W ELLNESS TV ADJUSTMENTS The keys in the figure at left can perform certain adjustments on the Wellness TV. In particular, it is possible to: ¾ Increase or reduce the brightness of the LCD. ¾ Increase or reduce the contrast of the LCD. Then: 1. Press the “ SAVE IN EEPROM ” key to permanently save the configuration. 2. Exit with the “ HOME ” key.

206. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 10.4 10.4. LIST OF CRITICAL SPARE PARTS Technogym medical devices are identified by “Serial N” plates that allow them to be tracked throughout the useful life-span of the device. Just as for products, there is also a list of so-called “critical” components which, through the Serial N, must be guaranteed as traceable. The list of these critical components is shown in the table below. CODICE COMPONENTE R0004473AB Brake board 0WR00503AB Solenoid assembly W0003767AA Display board 700 0WQ00060AA C-Safe board 0WR00633AA Salutron 8500 receiver W0003594AC Schurter socket - Display program – SW version - Brake board program – SW version If a critical component listed in this table is repl aced during a repair, maintenance or refurbishment, this fact must be noted in the “ Service report ” by recording the tracking information for the new component.

68. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.10 6.3.2. 500SP AND 700SP M ODELS The problem may be caused by the display Board don’t receiving the speed signal Is the user pedaling? Are the LEDs on the Display board lit on? Are the LEDs on the Brake board, lit on while pedaling? Correct operation: after 30 seconds without pedaling the machine swi t c h e s o f f Replace the Display board THE DISPLAY DOES NOT ILLUMINATE NO YES NO YES NO YES 2 1 B Replace the CU67 and/or CU62 cables Are the DC voltages at the output of the brake board correct? NO 3 Replace the Brake board YES 4 Continued on the following page

82. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.24 Is the v oltage at the input of the AUX board correct? Replace the AUX board YES 8 Is the v oltage at the output of the Digital TV board correct? Replace CU166 cable YES 9 NO A Is the v oltage at the output of the AUX board correct? Replace CU167 cable YES NO 11 Is the v oltage on the patch connector correct? 10 Replace Digital TV board NO Replace CU169 cable NO YES

90. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.32 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Carry out the “Standard Setting” procedure as detailed at paragraph 9.5.5. “ Standard settings ”. The speed sensor detects the heads of these bolts. (2) Powered models : Place the tester probes across the terminals of the speed sensor. The measured signal should be that indicated in Figure 3.2-1. In addition, when pedalling at 80 RPM the frequency of the signal should be 136 Hz. Self-Pow ered models : Check the signal on CU110 cable. The measured signal should be that indicated in Figure 3.2-1. In addition, when pedalling at 80 RPM the frequency of the signal should be 136 Hz. The speed signal can also be observed qualitatively, using a multimeter. The value should be 0 Vdc when the machine is sto pped, and gradually increase as the speed increases. (3) Update the low kit SW uploading both firmware and brake table. At the end carry out the “Default setting” procedure for the low kit parameters. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

76. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.18 6.6. NO TV PICTURE Check that the machine is connected to an antenna signal This error can be due to an incorrect machine configuration, or to problems with the antenna signal. ATTENTION - ONLY FOR JAPAN : Before to carry out the following troubleshooting, check that the B-CAS card is correctly inserted on the TV Digital Board. NO TV PICTURE Check if the antenna cable is properly connected Connect the cable NO 1 On the other machines y ou see the TV? Check the antenna signal. NO Connect the machines at one antenna soket sure working. Replace the antenna soket NO A YES YES Continued on the following page

98. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.40 Is the transmitter alway s within the 90 cm range f rom the receiv er NO Reposition the transmitter wit hin range YES Replace the receiv er A Is the transmitter in good working order? Use a correctly f unctioning transmitter YES NO 5 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the earth connection of the machine using a tester to measure the resistance between the ground pin on the power supply cable and the ground node to which the receiver is connected inside the display. The value must be less than 1 Ohm. (2) For machine positioning layouts, use the following diagram as a reference.

149. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 8.5 8.5. THE DISTANCE BETWEEN THE PEDALS Figure 8.5-1 Carry out the operations described in paragraph: 7.7. “ Disassembling the guards”, only the posterior guard. 1. Back off the counter nut (a) using a 17m m wrench. 2. Acting on the Shock absorber (b) with a 13mm wrench, for adjusting the distance between the footboards, in stand-by position, look again. Figure 8.5-2 3. Rotate the shock absorber in clock wise or counter clock wise, until the distance between the two pedals is 50mm , forcing them in its upper position.. Put some drops of Lo ctite on the counter nut (a), to fix it. ATTENTION: check that the shock absorber, even in its two extreme positions, i.e. with one lever at its end of travel and the other at rest, retains a slight amount of play rotating it on its axis.

43. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.11 3.2.3. T HE SIGNALS INVOLVED The machine uses the following control signals: • RS-485 Signal This is a digital signal exchanged between the Brake Board and the Display Board. There is no provision for monitoring its state. • Excitation current This is the current generated by the Brake B oard (pins 1-2 of connector CN2) which supplies the brake winding. The current supplied is a function of the adjustment algorithm. • Pulses This is the signal produced by the speed sensor, and has the waveform shown in the figure below: Figure 3.2-1 The signal enters the Brake Board ( pins 3-4 on connector CN2 ), where it is used to determine the speed value ( RPM )that is sent to the Display Board via the RS-485 serial link. This signal can also be measured qualitativ ely using a multimeter. The voltage measured across the sensor terminals should be 0 Vdc when the machine is stopped, and should increase to a few hundred mV during pedal m ovement: the higher the speed, the higher the measured voltage.

119. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.19 7.8. DISASSEMBLING THE UPPER COLUMN Figure 7.8-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”, only the anterior guard. 1. Back off the screws (a) using a 17m m wrench. Figure 7.8-2 2. Back off the screws (b) using a 17mm wrench. 3. Remove the upper part of the column pulling it out from the top. Pay attention to unplug the junction connectors of the cables which goes from the display to the lower electronic. Figure 7.8-3 To reassemble the upper column, carry out the above steps in reverse order. During reassembly, lock down the screws (a) and (b) using a torque wrench setting of 40Nm/29.5ft.lbf. Pay attention the cables are properly connected inside the frame, as shown in figure.

133. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.33 7.16. DISASSEMBLING THE SECONDARY SHAFT ASSEMBLY Figure 7.16-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”, only the anterior guard. 1. Rem ove the electronic box from the frame of the machine. 2. On the machine frame, mark the position where the secondary shaft is assembled, as indicated by the arrows in the example. 3. Back off the 4 screws (a) using a 17mm wrench. 4. Back off the screw (b) using a 17mm wrench, sliding down the frame on which the secondary shaft assembly is mounted, to slacken the belt tension. Figure 7.16-2 5. Back off the screw c using a 6mm hexagonal wrench, locking down the pin on the opposite side with an 8mm hexagonal wrench.

75. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.17 6.5. NO AUDIO SOUND This error can be due to an incorrect machine configuration, or to problems with the audio circuit. Is the TV standard correctly conf igured? Correctly conf igure the "TV Standard" parameter NO YES NO AUDIO SOUND 1 Replace the headphone jack. Does it work? Def ectiv e headphone jack YES NO Replace headphone connection cable. Does it work ? Def ectiv e headphone cable YES Replace the CPU board NO Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Carry out the configuration procedure as detailed at paragraph 9.5.6. “ TV Standard”. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version. The TV and RADIO channels is located in the Digital TV in the CPU Board and must necessarily be present. This means that when even one of the two boards will be replaced, should be re-stored channels thro ugh search or transferring from another machine via TGS key or cable transfer.

91. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.33 6.13. THE MACHINE DOES NOT READ THE TGS The machine displays this error if the TGS reader is not working properly, or if it is not supplied by the display board. THE MACHI NE DOES NOT READ THE TGS Is the v oltage at the input to the TGS reader correct? Is the v oltage at the output to the Display board correct? Replace cable CBQ-32 1 2 YES NO YES Replace the display board NO A Is the serial communication link between the display board and the TGS reader OK? Replace the TGS reader. Is the communication link between the display board and the TGS reader OK? TGS reader def ectiv e 3 3 YES NO YES Replace the display board NO A Replace the TGS reader Follow the procedure step by step to correctly di agnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below:

126. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.26 Figure 7.12-5 To reassemble the pedal lever, carry out the following procedure: 1. Thoroughly lubricate the taper bearings using Molykote G-4500/G grease, as shown in the figure below. 2. Grasp the lever at the point closest to the pedal and move it up and down, observing the amount of play. Do not grasp the lever from the pedal itself, as this might produce additional play associated with the fixing of the pedal. 3. Slowly begin tightening the ring, while continuing to move the lever, until there is no longer any play on the lever. If using a torque wrench, lock down with a setting of 15Nm/11.1ft.lbf. 4. At this point, tighten the ring further by another 45° (1/8th of a turn). although it may feel like the ring is not very tightly clamped, this amount of tightening is sufficient. 5. Exercise on the machine and check that there is not sensible play on the levers movement.

181. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.29 9.4.5.2. Low Kit fault code This function displays the error code that is blocking the low kit. To access this menu, when the display shows: LOW KIT FAULT CODE press ENTER , the following message appears: FAULT=XX In case of FAULT=00, the board is not in an error condition. 9.4.6. H IGH KIT VERSION This function displays the SW version of the display. To do this, when the display shows: HIGH KIT VERSION press ENTER , the message that identifies the SW version, will appear. 9.4.7. BOOT VERSION This function displays the BOOT version. To do this, when the display shows: BOOT VERSION press ENTER to display the message which identifies the BOOT version. 9.4.8. K EY R EADER V ERSION This function displays the KEY READER VERSION. To do this, when the display shows: KEY READER VERSION press ENTER to display the message which identifies the KEY READER version.

183. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.31 Here below have been detailed all the parameters of the menu. 9.5.1. L OW KIT PARAMETER This function provides access to parameters used for modifying certain settings of the lower assembly. To access this menu, when the display shows: In addition to the 13 configuration parameters, this function also includes the 3 sub-functions described below: 9.5.1.1. Read from low kit To read the parameter values from the low k it memory and view them on the display, press READ FROM LOW KIT key. 9.5.1.2. Write to low kit To write the values of the currently disp layed parameters to the low kit, press WRITE TO LOW KIT key. 9.5.1.3. Default Setting To load the default parameter values, press DEFAULT SETTING key.

39. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.7 3.1.8. B RAKE This is an eddy current brake, cons isting of a flywheel mass and a flat copper disk that rotates in the air gap of a winding. Variations in the winding current produce a change in the resulting field, which consequently varies the eddy currents induced within the copper disk and hence its resistance to movement. The winding has a resistance of approximately 3.5 Ohm. A klixon thermal cut-out, installed directly on the winding, interrupts the circuit whenever it detects a temperature exceeding 140°C. 3.1.9. S PEED SENSOR Only for 500, 700 and 700E versions. This consists of a magnetic induction sensor which detects the heads of the brake disk fixing screws. 3.1.10. NTC On the machine there are two NTC thermistors us ed for monitoring the temperature of the Brake board and the brake winding. The monitoring of th ese two components makes it possible to reduce the power when a given temperature threshold is reached, or open the circuit and cut off the power altogether if this reduction fails to stop the rise in temperature. 3.1.11. P OWER ENTRY MODULE This is a module consisting of: • power inlet socket; • power outlet socket; • fuse-holder for protecting line voltage and neutral with two 3.15A fast-blow fuses. It is situated on the side of the rear platform . The power entry module has a maximum current rating of 10 A. This places an upper limit on the number of machines that can be connected together. Therefore, do not connect more than 14 Cardio Wave Excite machines with a 220 VAC mains supply, or 7 machines with a 110 VAC mains supply. WARNING: If other types of machines are connected together, the maximum number is determined by their current draw.

92. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.34 (1) Place the tester probes across pins 1 and 8 of connector CN1 of the TGS reader. The measured value should be +12 Vdc. (2) As for step (1) but across pins 1 and 9 of connector CN8 on the display board. (3) Use the serial communications test described at paragraph 6.2.1.3 “ Serial Ports Test”. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

109. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.9 Figure 7.2-16 To disassemble the Digital TV and AUX input Board: 1. Work on the rear display support. 2. Disconnect the cable coming from the Input AUX Board and the antenna cable highlighted in the figure and the power supply cable. 3. Back off the 4 screws (o) with a medium Phillips screwdriver. 4. Remove the Digital TV Board. Figure 7.2-17 5. Slip off the AUX Input Board (p) from its housing. ATTENTION: During the reassembly of the Digital TV Board, pay attentions to not squash the cables under it. To reassemble the circuit boards, carry out the above steps in reverse order.

122. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.22 7.11. FOOTBOARD LEVER BELT DISASSEMBLY Figure 7.11-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”. 1. Push down the pedal on the side of the belt that is being disassem bled, in such a way that the belt cam is in the position shown in the figure. 2. Lock the cam in place by pushing a wrench or screwdriver behind the belt clamping block, and into a hole in the frame behind the cam. 3. Unhook the belt latch and pull from the insert on cam, as in figure at the side. Figure 7.11-2 4. Disconnect the tie-rod from the footboard lever belt, back off the screw (a) with a 6mm hexagonal wrench, looking the nut (b) with a 17mm wrench. Continued on following page →

103. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.3 7.1.3. 700WTV VERSION (W ELLNESS TV) Figure 7.1-7 Turn off the machine and unplug the mains lead from the wall outlet. 1. Back off the 4 screws (a) using a medium Phillips screwdriver. Figure 7.1-8 2. Unplug the connectors as indicated in the figure at left [CN30 - CN26 - CN27 - CN19 - CN20 - CN21 - CN22 - CN25]. 3. Remove the display. Figure 7.1-9 4. Back off the 2 screws (b) , using an 8mm Hexagonal wrench, to remove the rear display support. To reassemble the display, carry out the above steps in reverse order.

74. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.16 6.4. THE TOUCH SCREEN DOES NOT WORK / IT’S NOT CALIBRATED TOUCH SCREEN DOES NOT W ORK / NOT CALIBRATED Carry out the Touch Screen calibration procedure. Does it work correctly ? YES NO Touch Screen not calibrated Def ectiv e Touch Screen Replace CPU board Check and update the HW and SW related to the Touch Screen 2 Replace the Touch Screen. Does it work correctly ? NO YES 1 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) It’s recommended to upgrade the HW and SW of machine display to the last version, due to the steady work on the product for its improvement . Please refers to the proper section of the TG Direct web site: “Parts catalogue” and “Product release”. (2) Carry out the Touch Screen calibration procedure as detailed at paragraph 9.9. “ Touch screen calibration ”.

116. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.16 7.6. DISASSEMBLING THE SENSOR Figure 7.6-1 Turn off the machine and unplug the mains lead from the wall outlet: For each sensor: 1. Back off the 2 screws (a) using a medium Phillips screwdriver. Figure 7.6-2 2. Lift up the top sensor. 3. Remove the lower sensor. 4. To remove the sensors, unplug the two faston and the connector (b) of the touch sensor indicated in the figure. To reassemble the sensors, carry out the above steps in reverse order.

132. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.32 7.15. DISASSEMBLING THE BRAKE WINDING Figure 7.15-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”, only the anterior guard. 1. Unplug the two faston connectors (a) from the winding. 2. Unplug the connector circled in the figure at left. Figure 7.15-2 3. Back off the 2 screws (b) using an 17mm wrench, supporting the entire brake winding group (c) , to avoid damaging the copper disk. 4. Remove the brake winding assembly To reassemble the brake winding, carry out the above steps in reverse order. After completing the reassembly, adjust the position of the winding group as described in paragraph 8.3. “ Brake w inding position”.

93. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.35 6.14. THERE IS NO HEART RATE SIGNAL 6.14.1. SALUTRON TELEMETRIC RECEIVER The machine displays this error if: 1. electromagnetic noise saturate the HR receiver which does not display any value due to a specific SW filter which cut every signal, greater than 220 bpm; 2. the receiver is not working properly; 3. the receiver is not supplied by the display board. THERE I S NO HR SIGNAL Is the supply v oltage correct at the input to the receiv er? Is the supply v oltage correct at the output of the display board? Replace the receiv er Replace CU223 cable 2 3 YES NO YES Replace display board NO Carry out the troubleshooting procedure "THE TELEMETRIC SIGNAL IS INCORRECT" 1

120. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.20 7.9. BRAKE BOX DISASSEMBLY Figure 7.9-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”, only the anterior guard. 1. Back off the 2 screws (a) , with a 8m m wrench, to remove the Brake Box and replace if is necessary. Figure 7.9-2 2. Back off the screw (b) using a medium Phillips screwdriver. 3. Open the cover plate of the Brake box. Figure 7.9-3 4. Unplug the 4 connectors indicated in the figure at left. 5. Remove the Brake Box and replace if necessary. To reassemble the Brake box, carry out the above steps in reverse order.

176. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.24 9.4.2. O PERATING DATA This function makes it possible to access the machine usage data stored in the low kit. To access this menu, when the display shows: OPERATING DATA press ENTER . This function is structured as follows: OPERATING DATA Life Kit H Life Brake WRITE TO LOW KIT ? READ FROM LOW KIT ? Life Kit L Tot. Km KJ In addition to the machine usage data, this function also includes the 2 sub-functions described below: 9.4.2.1. Read from low kit To read the parameter values from the low kit memory and view them on the display, scroll using the +/- keys until the display shows: READ FROM LOW KIT ? press ENTER to read the errors from the low kit, and return to the upper menu level by pressing CLEAR for a few seconds.

108. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.8 Figure 7.2-13 7. Back off the 10 screws (i) using a small Phillips screwdriver. 8. Remove the touch screen protection plate (l) . Figure 7.2-14 9. Shift touch screen (m) on one side, paying attention to the cable which connect it to the CPU Board. Figure -7.2-15 10. Back off the 4 screws (n) using a small Phillips screwdriver. 11. Lift up and remove the LCD.

114. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.14 Figure 7.4-4 To reassembly the receiver: 1. On the Salutron receiver is possible to see the coil (e) and the connectors (f) and (g) . 2. Connect the cables to th e receiver, as in the figure to side. Figure 7.4-5 3. Wrap the receiver again in the sponge (h) , using a cable tie to fix it. 4. Reinsert the receiver inside of the home. ATTENTION: Position the receiver so that the coil is oriented towards the user. To reassemble the cardio receiver, carry out the above steps in reverse order.

118. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.18 Figure 7.7-4 7. Back off the screw (e) on both side of the machine, using a 5mm hexagonal wrench. 8. Pull out the central guard from the top. Figure 7.7-5 9. Remove the sweat protection guard (e1) if necessary. Figure 7.7-6 10. Overturn the machine on one side and back off the 4 nuts (f) using a 17mm wrench. 11. Place the machine in usage position and pull out the rear guard assembly from the top. During reassembly, lock down the screws (f) using a torque wrench setting of 27Nm/20ft.lbf. To reassemble the guards, carry out the above steps in reverse order.

159. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.7 9.2. USER MENU CONFIGURATION FOR 700 MODELS The machine configuration procedure is invoke d, when the machine is in standby mode, by simultaneously pressing the keys 369 , whereas on 700 Wellness TV models the keys 0369 must be pressed one after the other. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2406 and press ENTER to confirm. At this point the machine display begins showing the current configuration, structured as in the diagram below: USER MENU Language Pause time MAX time Distance TGS Keys HR Edit Messages Default config. Format P&P Change Mess.Lang. Languages SN Custom Mess. Cooldown time

177. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.25 9.4.2.2. Write to low kit To write the values of the currently displaye d parameters to the low kit, scroll using the +/- keys until the display shows: WRITE TO LOW KIT ? press ENTER to write the new data to the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.4.2.3. Machine usage data The machine usage data on the display is updated every 10 minutes. This means that, whenever the machine is switched off, any data modified after the last memory update will be lost. MESSAGE ON DISPLAY DESCRIPTION Life Brake: Minutes x 10 of operation of the brake Life Kit H: Minutes x 10 of operation of the upper assembly Life Kit L: Minutes x 10 of operation of the lower assembly Tot. Km: Total km traveled KJ Total KJ during exercise By selecting one of the items in the above table it is possible to modify its content, but only after having cleared its value. When the ENTER key is pressed the message "Reset life..." appears, followed by the name of the selected item; pressing ENTER again resets the value of the selected item, while pressing CLEAR reverts to the preceding value.

180. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.28 9.4.4. S TANDARD SETTINGS This function clears the operating data of the m achine and simultaneously resets the brake board parameters to their default values. To access this menu, when the display shows: STANDARD SETTINGS ? press ENTER , the following message appears: CONFIRM ? Press ENTER again to reset all parameters to their defa ult values, or return to the upper menu level by pressing CLEAR for a few seconds. This function does not alter the language and the TV standard setting. 9.4.5. L OW KIT MENU This function directly accesses the firmware of the brake board. To access this menu, when the display shows: LOW KIT MENU press ENTER . This function is structured as follows: LOW KIT MENU Low Kit Version Low Kit fault code 9.4.5.1. Low kit version This function displays the brake board firmware version. To access this menu, when the display shows: LOW KIT VERSION press ENTER , the following message appears: H:x L:x B:x Which identifies the firmware version.

99. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.41 where the value in the diagram indicates the medium distance for signal reception during the exercise (± 4” inches or 10 cm). (3) Check that the cardio receiver has been assemb led properly as described in the procedure: 7.4. “ Cardio/Hand sensor receiver disassembly”, th at is in good condition, work properly and the state of the band (ie battery). (4) To check for electromagnetic noise near the mach ine, use Test Box Excite as detailed here below. You can use one of the following cables ELT-16 ( 0WC00518AB ), CBQ-28 ( 0WC00390AC ) or TRM-28 ( 0WC00336AC ) as connection cable. The circuit lights the LED for each heart beat and/or disturbance received: in this way it is possible to determine whether there is any interference, and identify its sources. (5) Check the battery power level, using a tester if possible. Otherwise use a receiver or another reference machine to check the operation up to a distance of about 90 cm from the receiver. Receiver TEST BOX EXCITE HR receive r Connection cable

123. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.23 Figure 7.11-3 5. Unscrew the tie-rod (c) from the fastener on the belt using an 8mm wrench, without moving the nut (d) . 6. Separate the tie-rod from the fastener on the belt, pulling it out as illustrated in the figure During reassembly, lock down the tie- rod (c) using a torque wrench setting of 3.7Nm/2.72ft.lbf, until the nut is fully up against the clamping system. Lock down the nut using a torque wrench setting of 18Nm/13.3ft.lbf. If the nut has been moved from its original position, check in paragraph: 8.6. “ Tie rod length”. Figure 7.11-4 7. Disassemble the tie-rod fastener from the belt, by sliding component (e) along the belt. 8. Then remove the wedge (f) and the threaded connector (g) from the belt. Figure 7.11-5 To reassemble the belt, carry out the above steps in reverse order. The cams used on the two sides of the machine, are both the same part so check the proper point of connection for spring and belt.

141. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.41 7.20. DISASSEMBLING THE POWER ENTRY MODULE Figure 7.20-1 Turn the machine over on one side. 1. Back off the screws (a) using a medium Phillips screwdriver. 2. Remove the power entry module plate covering (b) . Figure 7.20-2 3. Back off the two screws (c) using a medium Phillips screwdriver and remove the power entry module. 4. Disconnect the cable (d) from the power entry module. 5. Remove the power entry module.

102. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.2 7.1.2. LED V ERSION 700 AND 700SP Figure 7.1-4 1. Turn off the machine and unplug the mains lead from the wall outlet (Only for 700). 2. Back off the 4 screws (a) using a medium Phillips screwdriver. Figure 7.1-5 3. Unplug the connectors as indicated in the figure at left [CN9-CN1-CN6-CN5-CN4]. 4. Remove the display. Figure 7.1-6 5. Back off the 2 screws (b) , using an 8mm Hexagonal wrench, to remove the rear display support. To reassemble the display, carry out the above steps in reverse order.

89. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.31 6.12. THE SPEED SIGNAL IS INCORRECT The speed signal is incorrect if: • The brake disk is incorrectly fixed to the flywheel; • The speed sensor is defective; • The brake board is defective. Does the speed sensor send the correct signal to the brake board? 3 Replace the speed sensor (generator on SP models) NO Replace the Brake board YES THE SPEED SIGNAL IS INCORRECT 1 YES YES Update the brake board SW. Is the speed signal correct? Def ectiv e SW NO Carry out the Standard Setting procedure 2

111. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.11 7.3.2. 700 AND 700SP LED V ERSION Figure 7.3-3 Carry out the operations described in paragraphs: 7.1. “ Display disassembly”. With the Display placed on a work bench: 1. Unplug the keyboard connector (a) [CN2] as in the side figure. Figure 7.3-4 2. Use a sharp tool to lift up and detach a corner of the keyboard. To assemble a new keyboard, with the display on a work bench: 1. Remove the backing film from the adhesive. 2. Apply the adhesive part, starting from the left and working toward the right, without bending the keyboard. 3. Insert the connector in the special slot on the display and connect it to the display board. 4. Remove the protective film. ATTENTION: When reassembling the keyboard, make sure that none of the keys are bent or remain pushed in. ATTENTION: The keyboard assembly procedure can only be carried out once, because disassembly damages the tracks and keys.

53. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 5.1 5. INSTALLATION INSTRUCTIONS 5.1. SPECIFICATIONS AND REQUIREMENTS For correct machine installation, make sure that: 1. The machine is installed on a level surface that is free of vibrations and has sufficient carrying capacity for the combined weight of the machine and user. 2. The place of installation is free of dust and sand. 3. The place of installation meets the operating temperature and humidity conditions specified in paragraph: 2.5. “ Ambient specifications”. 4. The m achine is not positioned close to sources of heat, sources of electromagnetic noise (television sets, electrical motors, antennas, hi gh voltage lines, household appliances, etc...) or medical equipment. 5. To eliminate any interference with the cardio receiver, no transmitters should be placed less than 90cm from the display. Only for the 500, 700 and 700WTV models: 6. The mains voltage must match the value specified on the machine rating plate. 7. The electrical system must be correctly earthed. 8. The wall outlet used should be reserved for the machine and have a rating of at least 100VA. 9. The maximum number of machines connected in cascade should be that indicated in paragraph 3.1.11. “ Power entry module”. 10. Position the m ains lead of the machine where it will not be underfoot.

101. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.1 7. DISASSEMBLY OF COMPONENTS 7.1. DISPLAY DISASSEMBLY 7.1.1. LED V ERSION 500 AND 500SP Figure 7.1-1 1. Turn off the machine and unplug the mains lead from the wall outlet (Only for 500). 2. Back off the 4 screws (a) using a medium Phillips screwdriver. Figure 7.1-2 3. Unplug the connectors as indicated in the figure at left [CN9-CN1-CN3]. 4. Remove the display. Figure 7.1-3 5. Back off the 2 screws (b) , using an 8mm hexagonal wrench, to remove the rear display support. To reassemble the display, carry out the above steps in reverse order.

23. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.11 2.7.3.2. 700 and 900 models ATSC Digital Tuner ATSC Standard DIGITAL TV BOARD Patch conn. J 1 Fan Patch conn. CPU BOARD C N 2 0 CU263 Power supply cable 2.7.3.3. 700 and 900 models ISDB-T Digital Tuner ISDB-T Standard DIGITAL TV BOARD Patch conn. J 1 Fan Patch conn. CPU BOARD C N 2 0 CU263 Power supply cable J 1 5 J 1 4 antenna cable CU248 J 1 2 B-CAS card reader CU210 J 7

140. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.40 7.19. SPEED SENSOR DISASSEMBLY Only for 700 e 700WTV models. Figure 7.19-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”, only the anterior guard. 1. Back off the 2 screws (a) using a 4m m hexagonal wrench. 2. Remove the speed sensor and its support. To remove only the sensor: 1. Cut the cable tie (b) . 2. Unplug the faston indicated in the figure. 3. Back off the 2 screws (c) using a small Phillips screwdriver and remove sensor. To reassemble the speed sensor, carry out the above steps in reverse order. After completing the reassembly, adjust the position of the sensor as described in paragraph 8.2. “ Speed sensor position”.

125. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.25 Figure 7.12-2 3. Push down the pedal on the side of the belt that is being disassembled, in such a way that the belt cam is in the position shown in the figure. 4. Lock the cam in place by pushing a wrench or screwdriver behind the belt clamping block, and into a hole in the frame behind the cam. Figure 7.12-3 5. Detach the tie-rod connected to the belt by the pedal lever, backing off the screw (c) using a 6mm hexagonal wrench and holding nut (b) in place with a 17mm wrench. Figure 7.12-4 6. Back off the ring nut (e) using a 17mm ring nut spanner and remove the two washer (f) . 7. Remove the lever from the pin on the frame. At last check the leng th of the tie rods as detailed at paragraph: 8.6. “ Tie rod length”. Continued on following page →

186. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.34 9.5.3.3. COM.Fault This is a counter that display the number of errors in serial communication between the upper and the lower kit. This counter increase each time a communication fault is detected. To reset this counter, press RESET key on the side of the value. To correctly display the parameter values, you need to load them from the low kit, using the “Read from low kit” function. For every error generated by the machine, the error history log records the information in the table below: • Counter • Error code • Current when the error occurred • Distance in km when the error occurred The correspondence between error codes and descrip tions is given in the “Service & maintenance manual”. Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

24. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.12 2.8. WIRING The connectors indicated in the following pages, refer to 700 model’s LED Boards, unless otherwise indicated. The colour of the cables can be changed, refer in particular to the Pin Out. 2.8.1. CBQ CABLES CBQ-13: CSafe board cable (Display Board – CSafe Board) Display Board CN8 Signal Colour CSafe Board; CN1 1 Digital #1 Flat cable 1 ... ... ... ... 14 Digital #14 Flat cable 14 CBQ-32: TGS Cable (Display/CPU Board – Patch connector) Display Board:CN7 CPU Board:CN8 Signal Colour Patch conn. 1 +12 Vdc power supply Red 8 3 Rx Brown 1 5 Tx Blue 2 9 Gnd Black 6

113. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.13 7.4. CARDIO/HAND SENSOR RECEIVER DISASSEMBLY Figure 7.4-1 Turn off the machine and unplug the mains lead from the wall outlet: 1. Back off the 6 screws (a) using a medium Phillips screwdriver. 2. Lift up the upper casing (b) . Figure 7.4-2 3. Unthread the receiver from its housing, with the protection sponge (c) . Figure 7.4-3 4. Remove the protection sponge and remove the cardio receiver (d) . Continued on following page →

134. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.34 7.16.1. 700 P OWERED AND 700WTV MODELS Figure 7.16-1 6. Remove the secondary shaft assembly from the belt and place it on a work bench. 7. Remove the spacer (d) and the pin (e) from the flywheel assembly. Figure 7.16-2 To disassemble the copper disk: 1. Back off the 6 screws (f) using a 4mm hexagonal wrench. Take particular care with the copper disk, as it bends easily and may then cause problems after reassembly, by brushing against the winding block. During reassembly, lock down the screws (f) using a torque wrench setting of 6Nm/4.4ft.lbf. To reassemble the secondary shaft assembly, carry out the above steps in reverse order. After completing the reassembly, carry out the adjustment procedure described in paragraph 8.1. “ Belt tension” and 8.4. “ Align the belt connecting the primary and secondary shafts”.

135. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.35 7.16.2. 700SP S ELF -P OWERED MODELS Figure 7.16-3 8. Back off the two screws (g) using a 3mm hexagonal wrench. 9. Back off the grub screw (h) using a 2.5mm hexagonal wrench. 10. Remove the piece (i) . 11. Remove the secondary shaft assembly from the belt and place it on a work bench. Figure 7.16-4 12. Remove the stator (l) from the flywheel (m) , pulling out one from the other. Continued on following page →

198. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.46 9.8.2. C ONNECTING TWO MACHINES USING A CS AFE CONNECTION (M ETHOD RECOMMENDED ) Disable the TGS reader (if presen t on the machine) through the proper function in the User Menu: 9.3.4. “ Enable TGS” before to carry out the follow ing procedure. 1. Connect the two machines together using the proper cable described at paragraph 4.3. “ Cable for exchanging TV channel tuning data between two m achines”. 2. On both machines, enter the configuration menu of the channels that need to be tuned. 3. Press the “ READ FROM TGS ” on the machine to be tuned the channels, appears on the machine the written “ WAITING ”, move on the machine from which you want to transfer channels and press the “ SAVE IN TGS ” button on the already tuned machine. 4. Store the data transferred on th e machine being tuned by pressing “ SAVE IN EEPROM ”. 5. Exit the menu on both machines by pressing “ HOME ”.

17. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.5 Working area: 2.5. AMBIENT SPECIFICATIONS Operating from 5° to 35° C Temperature Storage from -10° to 70° C Operating from 30% to 80% non- condensing Humidity Storage from 5% to 85% non-condensing 2.6. CONFORMITY TO REGULATIONS The machine conforms to the following standards: EUROPA USA EMI EN 55014-1 (2001) EN 55014-2 (1998) EN 61000-3-2 (2002) EN 61000-3-3 (1997) Safety EN 60335-1 (1998) EN 957-1 (2000) EN 957-9 classe SA (2003) Directives 73/23/CEE 89/336/CEE 98/37/CEE UL 1647 In addition: • Electrical isolation class: Class I; • Protection rating: IP21.

94. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.36 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Carry out the troubleshooting procedure 6.15. “ The telemetric heart rate signal is incorrect”. (2) Place the tester probes across pins 1 and 2 of connector HD4 of the receiver. The measured value should be +5 Vdc. (3) As for step (1) but across pins 1 and 6 of connector CN4 on the display board or CN19 on the CPU board. (4) Check the earth connection of the machine using a tester to measure the resistance between the ground pin on the power supply cable and the ground node to which the receiver is connected inside the display. The value must be less than 1 Ohm. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

96. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.38 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the earth connection of the machine using a tester to measure the resistance between the ground pin on the power supply cable and the ground node to which the receiver is connected inside the display. The value must be less than 1 Ohm. (2) Check the connections, referring to paragraph: 2.7. “ Wiring diagrams”. (3) Place the tester probes across pins 1 and 2 of connector HD4 of the receiver. The measured value should be +5 Vdc. (4) As for step (3) but across pins 1 and 6 of connector CN4 on the display board or CN19 on the CPU board.

110. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.10 7.3. 500AND 700 KEYBOARDS AND TOUCH SCREEN DISASSEMBLY 7.3.1. 500 AND 500SP MODELS Figure 7.3-1 Carry out the operations described in paragraphs: 7.1. “ Display disassembly”. With the Display placed on a work bench: 1. Unplug the keyboard connector (a) [CN2], shown in the figure. Figure 7.3-2 2. Use a sharp tool to lift up and detach a corner of the keyboard. To assemble a new keyboard, with the display on a work bench: 1. Remove the backing film from the adhesive. 2. Apply the adhesive part, starting from the left and working toward the right, without bending the keyboard. 3. Insert the connector in the special slot on the display and connect it to the display board. 4. Remove the protective film. ATTENTION: When reassembling the keyboard, make sure that none of the keys are bent or remain pushed in. ATTENTION: The keyboard assembly procedure can only be carried out once, because disassembly damages the tracks and keys.

19. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.7 2.7.1.2. Self-Powered version (500SP) DI SPL A Y AR M D ISPL AY B OAR D CBQ-13 KEYBOARD CSAFE BOARD C N 8 C N 1 C N 9 C N 1 C N 2 BRAKE BRAKE BOARD C N 3 C N 4 C N 1 C N 2 CU63 C N 3 NTC Patch Conn. CU71 Patch Conn. Patch Conn. CU69 CU67 Patch Conn. CU62 Patch Conn. DUAL TGS READER C N 7 CBQ-32 CU132 C N 1 HFU RECEIVER C N 1 ELT-16 BATTERY ALTERNATOR Patch conn. BATTERY CHARGER INPUT CU110

81. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.23 6.8. THE IPOD DOES NOT WORK Is the iPod detected by the machine? YES SI THE iPOD DOES NOT W ORK 1 Enter the audio/video files lis ts . C an y ou s ee the lis t of a ll the files uploaded on the iPod? Check the audio connection system NO Replace the Docking station board 2 3 YES Check the CU167 cable connection. Is the iPod detected by the machine? OK YES Is the voltage at the input of the docking station correct? Replace the docking station board YES 5 NO 6 NO A Update the iPod SW version Has been the device enabled from the proper function in the user menu? Enable the iPod NO 4 7 NO Continued on the following page

87. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.29 6.11. THE RESISTANCE IS INCORRECT The machine will produce an incorrect resistance if: • the mechanical components are not in perfect condition; • the speed measurement is incorrect; • the brake board is defective; • the brake is defective. Are the mechanics of the machine in good condition? Does the brake board output the correct current to the brake winding? Replace the brake board NO Replace the Brake winding YES THE RESISTANCE IS INCORRECT 2 Repair the f aulty mechanical parts NO Carry out the "Speed signal is Incorrect" troubleshooting procedure 3 Carry out the Standard Setting procedure 1 YES

115. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.15 7.5. FIXED HANDGRIPS DISASSEMBLY Figure 7.5-1 1. Back off the 6 screws (a) using a medium Phillips screwdriver. 2. Lift up the upper casing (b) . Figure 7.5-2 3. Back off the 4 screws (b) with a 6mm hexagonal wrench. During reassembly, lock down the screws (b) using a torque wrench setting of 27Nm/20ft.lbf. Figure 7.5-3 To disassemble all parts of the handlebar: 1. Back off the 2 screws (c) with a 6mm hexagonal wrench, on both side of the machine. During reassembly, lock down the screws (c) using a torque wrench setting of 62Nm/45.7ft.lbf. To reassemble the handlebar, carry out the above steps in reverse order.

178. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.26 9.4.3. E RRORS LOG This function accesses the machine’s error hist ory log. To access this menu, when the display shows: ERRORS LOG press ENTER . This function is structured as follows: ERRORS LOG Error 10 Error 1 RESET ERRORS ? READ FROM LOW KIT ? ....................... COM.Fault In addition to the error history log, this function also includes the 3 sub-functions described below: 9.4.3.1. Read from low kit To read the errors stored in low kit memory and view them on the display, scroll using the +/- keys until the display shows: READ FROM LOW KIT ? press ENTER to read the errors from the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.4.3.2. Reset Errors To clear the error history in bot h the low and high kit memory, scroll using the +/- keys until the display shows: RESET ERRORS ? press ENTER to clear the error history logs, and return to the upper menu level by pressing CLEAR for a few seconds.

72. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.14 3 NO Is the voltage at the input of the Brake board correct? NO YES Replace CU130 cable NO Replace the pow er entry module YES Are the voltages at the output of the Brake board correct? NO Replace the Brake board 5 B Are the voltages on the patch connectors 1 and 3 are correct? NO Replace CU67 and/or CU62 cables Are the voltages at the input of the Digital TV board correct? NO Replace CU169 cable YES YES YES 6 7 Are the voltages at the input of the CPU board correct? YES Re pla c e CPU b o ar d NO Replace CU169 cable 8 4 Is the voltage at the output of the pow er entry module correct?

138. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.38 Figure 7.17-4 10. Back off the grub screws (e) using a 3mm hexagonal wrench, on both the bearings. 11. Remove the bearings from the primary shaft. Figure 7.17-5 12. Remove from the shaft the plastic washers f and the free wheel (g) ( the washers are one on the external side and two on the internal side of the free wheel ) During reassembly, take care to fit the free wheels in the correct direction, so that they are able to rotate freely in the direction indicated by the arrows. Figure 7.17-6 13. Back off the 4 screws (h) locking down the nuts on the opposite side of the pulley, using a 13mm wrench 14. Remove the pulley from the shaft. To reassemble the primary shaft assembly, carry out the above steps in reverse order. After completing the reassembly, carry out the adjustment procedure described in paragraph 8.1. “ Belt tension” and 8.4. “ Align the belt connecting the primary and secondary shafts”.

175. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.23 9.4.1.3. Default Setting To load the default parameter values, scroll using the +/- effort level keys until the display shows: DEFAULT SETTING ? press ENTER to write the default values to the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. To write these parameters to the low kit, use the “Write to low kit” function. 9.4.1.4. Table of configuration parameters Parameter Description Defaultvalues Par 01 Transmission ratio 4248 Par 02 Speed ratio (integer part) 400 Par 03 Minimum braking current (standby pos.) [mA] 500 Par 04 Maximum continuous power [W] 200 Par 05 Machine torque correction coefficient (constant torque) 85 Par 06 User friction torque 10 Par 07 Maximum coil temperature [°C] 125 Par 08 Minimum revolutions [RPM] 35 Par 09 RPM integration scale 400 Par 10 Filter threshold [RPM] 400 Par 11 Speed ratio (decimal part) 0 Par 12 User friction torque delta 30 Par 13 NOT USED 48

166. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.14 Here below have been detailed all the parameters of the menu. 9.3.1. SN In the top right hand corner of th e windows it is displayed the SN of the machine, loaded at the end of the production line. 9.3.2. L ANGUAGE After selecting a language from the list of those available, all messages subsequently displayed by the machine will be in the chosen language. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.3. M EASURE It is possible to choose between EUROPEAN units (kg and km) or IMPERIAL units (pounds and miles). To change the selection, select the de sired option among the ones in the list, directly touching on the Touch Screen. M EASURE KM <default> MILES Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

187. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.35 9.5.4. SW VERSION DEVICES This function allows to display: • the low kit SW version (H:x L:x B:x); • the display SW version; • the key reader SW version; • the Digital TV board SW version; • the iPod docking station SW version; Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.5.5. S TANDARD SETTINGS This function allows you to reset the usage data of the machine and simultaneously set the default values of the parameters of the inverter. To make the restoration of values, press the STANDARD SETTINGS button This function does not change the language and standard television set.

142. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.42 7.21. DISASSEMBLING THE PLATFORMS Figure 7.21-1 Carry out the operations described in paragraph 7.7. “ Disassembling the guards” for removing the front guards. To disassemble the front platform: 1. Turn the machine over on one side, resting the frame on a box to keep the platform raised off the ground. 2. Back off the 5 screws (a) using a medium Phillips screwdriver and remove the 2 covering plates (b) . 3. Remove the front platform, pulling it out from the top. Pay attention during reassembly not to crush the cables which goes to the power entry module. Figure 7.21-2 To disassemble the bottom guard of the rear platform: 1. Turn the machine over on one side: 2. Back off the 4 screws (c) , using a 5mm hexagonal wrench and remove the bottom guard. To reassemble the platforms, carry out the above steps in reverse order .

85. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.27 6.10. THERE IS NO RESISTANCE The machine will not produce resistance if: • the display board is not receiving a speed signal; • the brake board is not generating current; • the brake is defective. Does the brake board supply tension at the brake? THERE I S NO RESISTANCE Are the Watt and SPM v alues shown on the display dif f erent from zero? NO YES 1 Carry out the "The speed signal is incorrect" troubleshooting procedure Replace the brake board YES Does the input of brake receiv e tension f rom the brake? NO Replace the brake YES Replace CU71 cable NO 3 YES Is the resistance on the Brake winding more or less 3.5 Ohm? Replace the brake NO 2 SELF-POWERED

170. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.18 9.3.15. S CREEN SAVER MINUTES It is possible to configure the amount of time, in minutes, the machine will wait before activating the screen saver, with values ranging from 10 to 360. To change the setting, press the MODIFY key and insert the value using the numeric keyboard. Press ENTER key to confirm or BACK key to back forward. The default value of this parameter is 10. Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.16. D ISPLAY IN THE WORKOUT It is possible to configure the si ze of the exercise data during the workout. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. D ISPLAY IN THE WORKOUT SMALL <default> LARGE Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

174. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.22 9.4.1. L OW KIT PARAMETER This function provides access to parameters used for modifying certain settings of the lower assembly. To access this menu, when the display shows: LOW KIT PARAM. press ENTER . This function is structured as follows: LOW KIT PARAM. Par.13 Par.01 WRITE TO LOW KIT ? DEFAULT SETTINGS ? READ FROM LOW KIT ? ....................... In addition to the 13 configuration parameters, this function also includes the 3 sub-functions described below: 9.4.1.1. Read from low kit To read the parameter values from the low kit memory and view them on the display, scroll using the +/- keys until the display shows: READ FROM LOW KIT ? press ENTER to read the errors from the low kit, and return to the upper menu level by pressing CLEAR for a few seconds. 9.4.1.2. Write to low kit To write the values of the currently displaye d parameters to the low kit, scroll using the +/- keys until the display shows: WRITE TO LOW KIT ? press ENTER to write the parameters to the low kit, and return to the upper menu level by pressing CLEAR for a few seconds.

160. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.8 9.2.1. L ANGUAGE After selecting a language from the list of those available, all messages subsequently displayed by the machine will be in the chosen language. To ch ange the selection, when the display shows the current setting: LANGUAGE : xxx Press the +/- GOAL keys to select the desired language from the options available. Press ENTER to confirm the choice, use the + or – effort level keys to move to the next or previous parameter. 9.2.2. D ISTANCE It is possible to choose between EUROPEAN units (kg and km) or IMPERIAL units (pounds and miles). To change the selection, when the display shows the current setting: DISTANCE : xxx Press the +/- GOAL keys to select the desired unit of m easurement from the options listed in the table below: D ISTANCE KM <default> MLS Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.2.3. M AXIMUM EXCERCISE TIME It is possible to set a maximum duration for the ex ercise in minutes, with a value ranging from 1 to 9999. To change the setting, when the display shows the current maximum exercise time: MAX TIME: xxx Press the ENTER key to modify the value: when the current parameter value starts to blink, press the CLEAR key to erase the current value and then us e the number keys to enter the desired new value. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 9999.

168. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.16 9.3.8. C OOLDOWN TIME It is possible to set the cooldown time for each ex ercise, ranging from 5 to 180 seconds. To change the setting, when the display shows the currently selected maximum time: Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 60. If you are exercising with a TGS key, the c ooldown will be stopped if you extract the key. 9.3.9. T OP EXERCISE PROGRAMS FOR YOU SHORTCUT It is possible to choose 2 extra training programs, from the list of those available, which will be displayed in the main page with the fixed ones “TIME” and “CALORIES”. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. T OP EXERCISE PROGRAMS FOR YOU Distance Training zone Fitness test Custom speed CPR Preset profiles Weight loss Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

61. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.3 Here below have been detailed all the parameters of the menu. 6.1.1. I2C D EVICE T EST The I2C Device test checks the communication fo llowing the 32K and 256K memories. The test can have two outcomes: • “Test Successful”: Signifies that data packets were successfully transmitted and received toward the display board. • “EEPROM Error” : Signifies that the display board has communication problems with the memories. 6.1.2. CS AFE COM TEST The test checks the communication on CSafe ports. The test can have two outcomes: • “Test Successful”: This means that the test was completed successfully, i.e. that serial communications on the selected port are correct. • “Error COM1”: This means that the outcome of the test was negative. The “CSafe COM test” done on a machine wh ich CSafe port is not plugged with the monitor plug described at chapter 4 of the Service & Maintenance manual. 6.1.3. L OW K IT COM T EST The test checks the communication with the Low kit. The test can have two outcomes: • “Test Successful”: This means that the test was completed successfully, i.e. that serial communications on the selected port are correct. • “Error COM2”: This means that the outcome of the test was negative.

117. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.17 7.7. DISASSEMBLING THE GUARDS Figure 7.7-1 Turn off the machine and unplug the mains lead from the wall outlet. 1. Back off the 5 screws (a) , using a 4mm hexagonal wrench, on both sides of the machine. During reassembly, insert the longer screws in the position indicated by the arrows. 2. Lift up the upper guard (b) securing it to the upper side of the machine with some adhesive tape or with a cord. Figure 7.7-2 3. Back off one of the 2 screw (c) , using a 5mm hexagonal wrench. 4. Remove the two front guards. Figure 7.7-3 5. Lower both the pedals. 6. Back off the 3 screws (d) using a 5mm hexagonal wrench. Continued on following page →

179. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.27 9.4.3.3. COM.Fault This is a counter that display the number of errors in serial communication between the upper and the lower kit. This counter increase each time a communication fault is detected. Scroll using the +/- keys until the display shows: COM.FAULT X To reset it press ENTER , the LED display shows: RESET COM.FAULT? press ENTER to reset and return to the upper menu level by pressing CLEAR for a few seconds. 9.4.3.4. View Errors For every error generated by the machine, the error history log records the information in the table below: • Counter • Error code • Current when the error occurred • Distance in km when the error occurred The correspondence between error codes and descriptions is given in the table below: Error Code Description 1 OVERHEATING: this condition occurs when the temperature detected by the sensor on the circuit board exceeds 90°C. 8 OVERVOLTAGE: this condition occurs when the +12 Vdc voltage goes above 13.7 Vdc (only on the 500, 700 and 700WTVmodels). Use the + effort level key to advance to the next error, otherwise the message w ith the details of the current error will continue to reappear.

18. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.6 2.7. WIRING DIAGRAMS 2.7.1. 500 MODEL (ARM B OARD ) 2.7.1.1. Powered version (500) DI SPL A Y ARM DISPLAY BOARD CBQ-13 KEYBOARD CSAFE BOARD C N 8 C N 1 C N 9 C N 1 C N 2 BRAKE BRAKE BOARD C N 4 C N 3 C N 1 C N 2 SPEED SENSOR Patch Conn. CU63 C N 3 NTC Patch Conn. CU71 Patch Conn. Patch Conn. CU69 CU67 Patch Conn. CU62 Patch Conn. DUAL TGS READER C N 7 CBQ-32 CU132 C N 1 HFU RECEIVER C N 1 ELT-16 POWER ENTRY MODULE VAC CB-1 CU130 Gr ound

207. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 11.1 11. SCHEDULED MAINTENANCE To keep the machine in perfect working order a nd forestall possible problems it is necessary to carry out the scheduled maintenance operations de scribed below. The maintenance operations can essentially be classified according to the frequency with which they need to be performed: • Daily maintenance operations; • Monthly maintenance operations; • Twice-yearly maintenance operations. The operations require different levels of operato r qualification. The following paragraphs describe the recommended procedures. 11.1. DAILY MAINTENANCE OPERATIONS These operations can be carried out by the machine owner and do not require any special skills. The daily machine maintenance consists of simple external cleaning, for the purposes of general hygiene. For the daily maintenance of the machine, proceed as follows: 11.1.1. S ETTING UP THE OPERATION 1. Turn off the machine by placing the switch in position 0 (OFF). 2. Unplug the mains lead from the wall outlet. 11.1.2. E XTERNAL CLEANING OPERATIONS 1. Using a cloth moistened with Clean Well, clean the entire machine, taking care not to rub too vigorously, especially on the keys of the display. Never spray the cleaning product directly on the machine. WARNING: do not use alcohol, petrol or other chemical products.

208. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 11.2 11.2. MONTHLY MAINTENANCE OPERATIONS These operations can be carried out by the machine owner and do not require any special skills. The monthly maintenance operations consist of simple checks on the machine’s operation and state of wear, to ensure its safe and correct functioning. For the monthly maintenance of the machine, proceed as follows: 11.2.1. C LEANING OPERATIONS 1. Use a vacuum cleaner to clean the interior, paying particular attention to the brake. WARNING: when carrying out these operations, be careful not to damage the cables. 11.2.2. C HECKING THE STATE OF WEAR OF THE PEDAL LEVER BELT 1. Check the state of wear of the pedal lever belt, inspecting their entire length and. If any anomalies are found, call in the authorized Technogym Technical Service. 11.2.3. C HECKING THE AMOUNT OF PLAY ON THE BALL JOINTS 1. Check the amount of play on the ball joints. If any anomalies are found call in the authorized Technogym Technical Service. 11.2.4. C HECKING THE OPERATION OF THE CARDIOTESTER RECEIVER 1. Using a separate heart rate monitor, put on the transmitter band and check that the machine and the separate monitor both measure the same heart rate, and that when the band is disconnected the machine does not receive any signal. 2. Using a heart rate frequency simulator, check th at the machine detects variations in the heart rate. 11.2.5. C HECKING THE OPERATION OF THE HAND SENSOR RECEIVER 1. Using a separate heart rate monitor, grasp the hand sensors and check that the machine and the separate monitor both measure the same heart rate , and that when the sensors are released the machine does not receive any signal.

33. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.1 3. PRINCIPLES OF OPERATION 3.1. BLOCK DIAGRAM The machine block diagram is illustrated in the figure below: DISPLAY LED DISPLAY DISPLAY BOARD C-SAFE BOARD HS/HR RECEIVER DUAL TGS READER KEYBOARD Ante nna inlet (only WTV) (Left) HAND SENSOR (Left) TOUCH SENSOR (Right) TOUCH SENSOR WTV DISPLAY TOUCH SCREEN INPUT AUX BOARD L R C-SAFE V iPOD DOCKING STATION DIGITAL TV BOARD tuner (Right) HAND SENSOR POWERED VERSION POWER ENTRY MODULE BRAKE BOARD VAC SPEED SENSOR BRAKE NTC SELF-POWERED VERSION NTC BRAKE BATTERY BRAKE BOARD BATTERY CHARGER INPUT Ex te rna l power supply

153. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.1 9. MACHINE CONFIGURATION 9.1. USER MENU CONFIGURATION FOR 500 MODELS The machine configuration procedure is invoke d, when the machine is in standby mode, by simultaneously pressing the keys ENTER , ↑ , CLEAR . The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2406 and press ENTER to confirm. To enter the password, increase or decrease the displayed value using the ↑ and ↓ keys, or use the +/- GOAL keys to scroll through and modify the individual digits. At this point the machine display begins showing the current configuration, structured as in the diagram below: USER MENU Language MAX time Cooldown time Distance Pause time Default age Default weight Default calories Keys Format P&P Default distance TGS Default Config. Default time HR SN

21. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.9 2.7.2.2. Self-Powered version (700SP) DISPLAY ARM DISPLAY BOARD CBQ-13 KEYBOARD CSAFE BOARD C N 8 C N 1 C N 9 C N 1 C N 2 BRAKE BRAKE BOARD C N 3 C N 4 C N 1 C N 2 CU63 C N 4 NTC Pa t c h Conn. CU71 C N 5 C N 6 Pa t c h Conn. Pa t c h Conn. CU69 CU67 HS/HR RECEIVER BOARD SALUTRON 8500 H D 4 H D 3 & 2 L LOWER SEN SOR R UPPER SEN SOR L UPPER SEN SOR R LOWER SEN SOR RIGHT TOUCH SEN SOR LEFT TOUCH SEN SOR H D 1 Pa t c h Conn. CU222 CU62 CU223 CU224 Pa t c h Conn. DUAL TGS READER C N 7 CBQ- 32 CU132 C N 1 BATTERY ALTERNATOR Pa t c h conn. BATTERY CHARGER INPUT CU110

29. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.17 CU169: Display power supply cable (CPU board – Digital TV board – Patch conn. 1) Patch connn. 1 Signal Colour CPU board CN20 Digital TV board J1 1 GND Yellow/Green 1 - 2 GND 12Vdc Black 2 - 3 GND 5Vdc Black - 2 4 sensing GND 5Vdc Black - 4 5 n.c. - - - 6 +12Vdc Red 6 - 7 +5 Vdc Red - 1 8 sensing + 5Vdc Red - 3 CU210: B-CAS Board signal cable (Digital TV Board –B-CAS board card reader) Digital TV Board J12 Signal Colour B-CAS board card reader 1 n.c. - - 2 n.c. - - 3 Data out Black 4 4 Clock Black 6 5 n.c. - - 6 Reset Black 2 7 GND Black 5 8 +5 Vdc Black 1 9 GND Black 7 10 Card detection Black 8

196. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.44 To tune and memorise radio channels, proceed as follow: It is now possible only the tuning of the digital band and not more the analogue one. 1. Press AUTOMATIC SEARCH. In th is phase, a temporary list of TV channels found, will be stored and visualized in column 1 . In column 2 there are the number of the channels. 2. Wait the search stops or stop it by pressing STOP SEARCH key. The channels found in the meantime can be memorised. 3. Use the keys under the list of channels in column 1 , to scroll through the pages with the channels found during the search, while use the keys under the list of numbers in column 2 , to scroll through the pages with the numbers and names associated to the channels. 4. Once you have found a channel to memorise, select it in column 1 , then press the number that you want to associate it with, in column 2 . If a channel has already been memorised under that number, the old channel will be overwritten with the new one. 5. Repeat the procedure above for each channel you want to memorise. 6. In this way the channels will remain in the memory until the equipment is switched off ( RAM memory ); to permanently memorise the changes ( in EPROM ) press SAVE IN EPROM key. 7. Exit with “HOME” key.

184. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.32 9.5.1.4. Table of configuration parameters To correctly display the parameter values, you need to load them from the low kit, using the “Read from low kit” function. To change the setting, press the CHANGE key and insert the value using the numeric keyboard. Press ENTER key to confirm or BACK key to back forward. After any changes to the parameter values, you need to load them in the low kit using the “Write to low kit” function. Parameter Description Default values Par 01 Transmission ratio 4248 Par 02 Speed ratio (integer part) 400 Par 03 Minimum braking current (standby pos.) [mA] 500 Par 04 Maximum continuous power [W] 200 Par 05 Machine torque correction coefficient (constant torque) 85 Par 06 User friction torque 10 Par 07 Maximum coil temperature [°C] 125 Par 08 Minimum revolutions [RPM] 35 Par 09 RPM integration scale 400 Par 10 Filter threshold [RPM] 400 Par 11 Speed ratio (decimal part) 0 Par 12 User friction torque delta 30 Par 13 NOT USED 48 Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

63. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.5 6.2. SERVICE TROUBLESHOOTING MENU: MODELLI LED Te configuration procedure is invoked when the machine is in standby mode, using a different procedure for the 500 and 700 models. • Accessing configuration of 500 models Simultaneously press the ENTER , ↑ , CLEAR keys. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2501 which protects against unauthorized access and press “Enter” to confirm. To enter the password, increase or decrease the displayed value using the ↑ and ↓ keys, or use the +/- GOAL keys to scroll through and modify the individual digits. At this point there are two options available: ↑ = Tech Config ↓ = Troubleshooting Press numeric key ↑ to access the menu for configuring tec hnical parameters; the machine display will begin showing the current configuration, structured as in the diagram below: • Accessing configuration of 700 models Simultaneously press the keys 369 for 700 LED models, whereas on 700 Wellness TV models the keys 0369 must be pressed one after the other. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2501 which protects against unauthorized access and press the “Enter” key to confirm. At this point there are two options available: 1 = Tech Config 2 = Troubleshooting Press numeric key 1 to access the menu for configuring technical parameters; the machine display will begin showing the current configuration, structured as in the diagram below:

191. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.39 A. To tune and memorise Digital TV channels, proceed as follow 1. Press DIGITAL SEARCH. In this phase, a temporary list of TV channels found, will be stored and visualized in column 1 . 2. Wait the search stops or stop it by pressing STOP SEARCH key. The channels found in the meantime can be memorised. 3. Use the keys under the list of channels in column 1 , to scroll through the pages with the channels found during the search, while use the keys under the list of numbers in column 2 , to scroll through the pages with the numbers and names associated to the channels. 4. Once you have found a channel to memorise, select it in column 1 , then press the number that you want to associate it with, in column 2 . If a channel has already been memorised under that number, the old channel will be overwritten with the new one. 5. Repeat the procedure above for each channel you want to memorise. 6. In this way the channels will remain in the memory until the equipment is switched off ( RAM memory ); to permanently memorise the changes ( in EPROM ) press SAVE IN EPROM key. 7. Exit with “HOME” key. Up to 190 TV channels can be memorised, a furthe r channel is reserved for the A/V signals from DVD player, VHS or from the game console.

34. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.2 3.1.1. LED ARM D ISPLAY BOARDS (500 AND 500SP) The display contains only one board which compri ses the CPU, an ARM microprocessor, its logic circuits and a FLASH EPROM containing the operati ng program for the machine moreover, acts as the interconnection hub for all the components of the display and serves as the point of connection with the brake Board. The main functions of the board are: ¾ Manages and process signals from: • Keyboard; • HR receiver; • CSafe Board; • TGS reader (if present). ¾ distributes the voltages received from the Brake Board to the display; ¾ exchanges, via the RS-485 serial link to the Brake Board, the commands for controlling the brake; ¾ controls the LEDs and the 7-segment displays which provide feedback about the exercise session. The board includes the following indicator LEDs: LED name Colour Description LED1 green if ON the +12 Vdc power supply fr om the Brake Board correctly reaches the board. LED2 yellow if ON the +5 Vdc power supply from the Brake Board correctly reaches the board.

161. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.9 9.2.4. P AUSE TIME It is possible to set a maximum pause time for each exercise in seconds, with values ranging from 10 to 999. To change the setting, when the display shows the current maximum time: PAUSE TIME : xxx Press the ENTER key to modify the value: when the curre nt parameter value starts to blink, press the CLEAR key to erase the current value and then us e the number keys to enter the desired new value. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 60. 9.2.5. C OOLDOWN TIME It is possible to set the cooldown time for each ex ercise, ranging from 5 to 180 seconds. To change the setting, when the display shows the currently selected maximum time: COOLDOWN TIME xxx Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 60. If you are exercising with a TGS key, the c ooldown will be stopped if you extract the key. 9.2.6. E NABLE TGS It is possible to enable or disable the use of the TGS reader. To change the selection, when the display shows the current setting: TGS : xxx Press the +/- GOAL keys to select the desired option out of those listed in the table below: TGS ENABLED <default> DISABLED Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter.

137. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.37 7.17. DISASSEMBLING THE PRIMARY SHAFT ASSEMBLY Figure 7.17-1 Carry out the operations described in paragraph 7.7. “ Disassembling the guards”. 1. Push down the pedal on the side of the belt that is being disassem bled, in such a way that the belt cam is in the position shown in the figure. 2. Lock the cam in place by pushing a wrench or screwdriver behind the belt clamping block, and into a hole in the frame behind the cam. Carry out the operati ons at steps 1 and 2 on both the cams, to slacken the tension of the belts. Figure 7.17-2 3. Back off the 4 screws (a) using a 17mm wrench. 4. On the machine frame, mark the position where the secondary shaft is assembled, as indicated by the arrows in the example. 5. Back off the screw (b) , using a 17mm wrench, to slacken the tension of the belt that connects the primary shaft to the secondary. Figure 7.17-3 On both side of the machine: 6. Derail the belt from the pulley (c) . 7. On the machine frame, mark the position where the bearing ( which hold the primary shaft ) are assembled, as indicated by the arrows in the example. 8. Back off the screws (d) using a 19mm, locking down the nuts on the opposite side using a 19mm. 9. Remove the primary shaft assembly from the two belt pedal lever. Continued on following page →

154. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.2 9.1.1. L ANGUAGE After selecting a language from the list of those available, all messages subsequently displayed by the machine will be in the chosen language. To ch ange the selection, when the display shows the current setting: LANGUAGE : xxx Press the +/- GOAL keys to select the desired language from the available options. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.1.2. U NITS OF MEASUREMENT It is possible to choose between EUROPEAN units (kg and km) or IMPERIAL units (pounds and miles). To change the selection, when the display shows the current setting: UNITS : xxx Press the +/- GOAL keys to select the desired unit of m easurement from the options listed in the table below: U NITS KG <default> POUNDS Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.1.3. M AXIMUM EXERCISE TIME It is possible to set a maximum duration for each exercise, ranging from 1 to 9999 minutes. To change the setting, when the display shows the currently selected duration: MAX. DURATION : xxx Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 9999.

158. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.6 9.1.13. M ODIFIABLE TARGET FREQUENCIES It is possible to enable or disable modification of the target heart rate during a constant heart rate exercise. To change the selection, when the display shows the current setting: HR : xxx Press the +/- GOAL number keys to select the desired option out of those listed in the table below: HR MODIFIABLE <default> NON MODIFIABLE Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.1.14. R ESETTING PARAMETERS TO DEFAULT VALUES It is possible to reset the user menu parameters to their default values. To select the function, when the display shows: DEFAULT CONFIG. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. If the ENTER key is pressed the display will show: CONFIRM ? press ENTER to confirm, or cancel by pressing the CLEAR key for a few seconds. 9.1.15. F ORMAT P&P KEY This function formats a TGS key for Plug&Play mode operation. To select the function, when the display shows: FORMAT P&P Press ENTER to confirm. At the end of the formatting procedure, hold down the CLEAR key for a few seconds to exit. The CLEAR key can be pressed at any time to interrupt the procedure and revert to standby mode. 9.1.16. SN This parameter shows the serial number of the machine. SN:xxxxx

172. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.20 9.4. SERVICE MENU CONFIGURATION FOR 500 AND 700 LED MODELS The configuration procedure is invoked when the machine is in standby mode, using a different procedure for the 500 and 700 models. 3. Accessing configuration of 500 models Simultaneously press the ENTER , ↑ , CLEAR keys. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2501 which protects against unauthorized access and press “Enter” to confirm. To enter the password, increase or decrease the displayed value using the ↑ and ↓ keys, or use the +/- GOAL keys to scroll through and modify the individual digits. At this point there are two options available: ↑ = Tech Config ↓ = Troubleshooting Press numeric key ↑ to access the menu for configuring tec hnical parameters; the machine display will begin showing the current configuration, structured as in the diagram below: 4. Accessing configuration of 700 models Simultaneously press the keys 369 for 700 LED models, whereas on 700 Wellness TV models the keys 0369 must be pressed one after the other. The following prompt appears on the display: ENTER PASSWORD: To access the procedure, type in the password 2501 which protects against unauthorized access and press the “Enter” key to confirm. At this point there are two options available: 1 = Tech Config 2 = Troubleshooting Press numeric key 1 to access the menu for configuring technical parameters; the machine display will begin showing the current configuration, structured as in the diagram below:

20. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.8 2.7.2. 700 MODEL (ARM BOARD ) 2.7.2.1. Powered version (700) DISPLAY ARM DI SPLAY BOARD CBQ-13 KEYBOARD CSAFE BOARD C N 8 C N 1 C N 9 C N 1 C N 2 BRAKE POWER ENTRY MODULE BRAKE BOARD C N 4 C N 3 C N 1 C N 2 SPEED SENSOR Patch Conn. CU63 C N 4 NTC Patch Conn. CU71 C N 5 C N 6 Patch Conn. Patch Conn. CU69 CU67 HS/ HR RECEI VER BOARD SALUTRON 8500 H D 4 H D 3 & 2 L LOWER SENSOR R UPPER SENSOR L UPPER SENSOR R LOWER SENSOR RI GHT TOUCH SENSOR LEFT TOUCH SENSOR H D 1 Patch Conn. CU222 CU62 CU223 CU224 Patch Conn. DUAL TGS READER C N 7 CBQ-32 CU132 C N 1 VAC CU130 CB-1 Ground

35. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.3 3.1.2. L ED A RM D ISPLAY B OARDS (700 AND 700SP) The display contains only one board which compri ses the CPU, an ARM microprocessor, its logic circuits and a FLASH EPROM containing the opera ting program for the machine moreover, acts as the interconnection hub for all the components of the display and serves as the point of connection with the Brake Board. The main functions of the board are: ¾ Manages and process signals from: ƒ Keyboard; ƒ HS/HR receiver; ƒ Touch sensor ƒ CSafe Board; ƒ TGS reader (if present). ¾ distributes the voltages received from the Brake Board to the display; ¾ exchanges, via the RS-485 serial link to the Brake Board, the commands for controlling the brake; ¾ controls the LEDs and the 7-segment displays which provide feedback about the exercise session. The board includes the following indicator LEDs: LED name Colour Description LED1 green if ON the +12 Vdc power supply fr om the Brake Board correctly reaches the board. LED2 yellow if ON the +5 Vdc power supply from the Brake Board correctly reaches the board.

130. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.30 7.14. DISASSEMBLING THE LEVERS TENSIONING SPRING Figure 7.14-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”, only the anterior guard. 1. Pull up the pedal opposite the spring that is being disassem bled, in order to unload the spring as much as possible. 2. Back off the screw (b) using a 5mm hexagonal wrench, using a pliers to keep the spring (a) . Be careful because the spring might remain slightly loaded, exerting pressure on the screw ”b”. Figure 7.14-2 3. Back off the screw (c) using a 3mm hexagonal wrench to remove the screw, the washer and the other two components used to fix the spring. During reassembly, remember to put all the components in the proper order as shown in the figure to side. Figure 7.14-3 4. Remove the spring (d) pulling it out on the side. To disassemble the cam: 1. Disconnect the belt from the cam, as detailed in the procedure 7.11. “ footboard lever Belt disassem bly”. 2. Back off the pin (e) using a 12mm hexagonal wrench. 3. remove the cam (f) . Continued on following page →

107. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.7 Figure 7.2-10 CPU Board (B) : 1. Disconnect the cables indicated in the figure, coming from TTL Board [CN3], Touch screen [CN28A], inve rter LCD [CN5] and headphone jack [J3]. ATTENTION: to disconnect the cable coming from the touch screen, bend lightly back the protection plate, if necessary. 2. Back off the 6 screws (e) with a small Phillips screwdriver. 3. Remove the CPU Board. Figure 7.2-11 To disassemble LCD and Touch Screen: 1. Disconnect the cable’s connectors coming from TTL and Touch screen [CN3-CN28A], on CPU Board. On the inverter those direct to the LCD inverter indicated in the figure [CN2-CN3]. ATTENTION: to disconnect the cable coming from the touch screen, bend lightly back the protection plate, if necessary. 2. Back off the 5 screws (f) , which fix the plate with all the Display Boards, to the front covering. Figure 7.2-12 3. Back off the 2 screws (g) which fix the headphone jack at the display with a small Phillips screwdriver. 4. Disconnect the connector (h) . 5. Remove the headphone jack from the display housing. 6. Lift up the plate on which all the circuit boards and the LCD are fixed. Continued on following page →

25. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.13 2.8.2. CU CABLES CU62: Power supply cable between upper Kit and lower Kit (Patch conn. 2 - Display Board) Patch conn. 2 Signal Colour Display Board CN20 2 Gnd White 2 3 Gnd Yellow 3 4 - sensing +5 Vdc digital Pink 4 6 +12 Vdc Brown 6 7 +5 Vdc Green 7 8 +sensing +5 Vdc digital Grey 8 CU63: Serial communication cabl e between upper Kit and lower Kit (Patch conn. 3 - Display Board) Patch conn. 3 Signal Colour Display Board CN30 1 Digital Gnd Orange-White 1 2 Digital Gnd Orange 2 3 NC Green-White 3 4 Download Green 4 5 Reset Blue-White 5 6 NC Blue 6 7 485 Tx/Rx + Brown-White 7 8 485 Tx/Rx - Brown 8 CU69: Serial communication cabl e between upper Kit and lower Kit (Brake board - Patch conn. 3) Brake board CN3 Signal Colour Patch conn. 3 1 Digital Gnd Orange-White 1 2 Digital Gnd Orange 2 3 NC Green-White 3 4 Download Green 4 5 Reset Blue-White 5 6 NC Blue 6 7 485 Tx/Rx + Brown-White 7 8 485 Tx/Rx - Brown 8

26. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.14 CU71: Brake supply cable (Brake board – Brake – Speed sensor – NTC) Brake board CN2 Signal Colour Brake Speed sensor NTC 1 Brake supply + Brown Faston - - 2 Brake supply - Brown Faston - - 3 SPM Red - Faston connected to brown cable - 4 SPM Reference Black - eyelet - 5 NTC + White - - 2 (Orange) 6 NTC - White - - 1 (Grey) CU67: Power supply cable between upper and lower assemblies (Brake board – Patch conn. 1) Brake board CN1 Signal Colour Patch conn. 1 2 Gnd White 2 3 Gnd Yellow 3 4 - sensing +5 Vdc digital Pink 4 6 +12 Vdc Brown 6 7 +5 Vdc Green 7 8 +sensing +5 Vdc digital Grey 8 CU110: Alternator cable (Brake board – Alternator – Battery – Inlet for battery charging) Brake board CN3 Signal Colour Alternator Battery Battery charging inlet 1 V+ voltage from alternator Red Faston - 2 V- voltage from alternator Black Faston - 3 RPM signal White Faston 4 V+ voltage from battery charger Red - soldered to internal contact 5 V- voltage from battery charger Black - soldered to external contact 6 Battery V+ Red - Faston - 7 Battery V- Black - Faston -

203. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 10.1 10. FUNCTIONAL TEST MD MODELS Every time maintenance and/or repairs are performe d on a machine, it is necessary to carry out a series of mechanical and electrical tests to ensure: ™ that the medical device is working properly; ™ that the medical device is working safely; ™ that the exercises are performed according to the biomedical specifications for which the medical device was designed. Technogym ® ensures its own safety standards by means of the following tools and activities: ™ ISO 9001/2000 certification of the company; ™ certification of the device in compliance with medical regulations 60601-1 and 60601-1-2; ™ electrical testing of each device manufactured, according to the provisions of the aforementioned standards; ™ training of technical staff who perform technical service; ™ use of checked and tested original Technogym® spare parts for all service operations. 10.1. ELECTRICAL SAFETY TEST Based on the risk analysis carried out by the Af ter Sale department regarding installation and technical service, it is still necessary to use a tester to perform a safety test on the grounding ring. This test must ensure a continuous earth conn ection (resistance less than 4 Ohm) between the grounding pole of the mains lead (connected to the machine) and the 6 points listed below: ™ Handlebar holding screw; ™ water bottle holding screw; ™ guards fastening screw (on both sides). ™ footboard lever fastening screw (on both sides); For more complete explanations, see the boxes in the figure below.

38. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.6 3.1.5. D UAL TGS READER It’s the device which allows the machine to interact with the Wellness System. This board enables the machine to read the us er's TGS key for performing workouts programmed with the propers SW of the Wellness System. With Dual TGS reader it is possible to use both the Botom and the Mifare TGS keys. 3.1.6. C ARDIO RECEIVER This board manages the signal received from the telemetric transmitter used by the person exercising. It receives the power supply signal from the Display Board and outputs a negative logic pulse for every heart beat that is detected: the si gnal level is normally 5 Vdc, with a pulse at 0 Vdc (having a width of approximately 30 msec) at each heart beat. The receiver reception area is approximately with a 90 cm radius. If there is electromagnetic noise (produced by high voltage lines, radio transmitters, monitors, motors etc.) within this area, the receiver becomes saturated and no longer receives any signal. The Salutron 8500 models, manage both the telemetr ic transmitter and the hand sensors signals, in the same way. 3.1.7. B RAKE BOARD There are 2 versions of the Brake Board, one whic h is used on the mains powered version and the other on the self-powered version. In either case, the Brake Board consists of: • Power supply section which generates the low vo ltages used by the machine: +5 Vdc and +12 Vdc. Depending on the machine version, these volt ages will be generated either from the 110 VAC or 220 VAC mains supply, or from the alternator-battery. • Section for RS-485 serial communications with the Display Board for: ƒ commands determining the resistance that is required of the brake; ƒ brake error messages; ƒ commands for modifying the circuit board configuration parameters; ƒ commands for viewing the errors logged by the circuit board. • Section which generates the current for the brake winding: varying the current produces a proportional variation in the resistance of the brake. The excitation current supplied to the brake is a function of the effort level select ed on the display and the RPM value measured by the speed sensor (angular velocity of the brake di sk) and is determined by the values stored in the braking table. The board includes the following indicator LEDs: LED name Colour Description LED1 green if ON the board is supplying the brake winding. if BLINKING the Brake Board is in an error condition. LED2 yellow if ON there is the +5 Vdc supply from the circuit Board.

64. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.6 MAN.KEYBOARD TEST TROUBLESHOOTING I2C Devices Test AUTOMATIC TEST MANUAL TEST LED Test SERIAL PORTS TEST CSafe COM Test TGS COM Tes t Low Kit COM Test To scroll through the list of available functions, press the + or – effort level keys to display the next or the preceding item; confirm the choice by pressing ENTER . To cancel the operation, press the CLEAR key for a few seconds. The tests are divided into two groups: Automatic and Manual , and the prompt for a choice appears immediately on accessing the troubleshooting menu. 6.2.1. A UTOMATIC T EST The tests grouped under this section conduct checks on the machine’s operation in a fully automatic manner. After selecting the desired test using the + and – effort level keys, press ENTER to initiate the test and then await the result. Press ENTER again to continue, and use the CLEAR key to return to the higher menu level, holding it down fo r a few seconds. The various tests are described below. 6.2.1.1. I2C Devices Test The I2C Devices test checks the communication following the 32K and 256K. The test can have outcomes: • “Test Successful, press Enter to continue” : Signifies that the transmission and reception of data packets between the I2C devices and the display board was completed successfully. • “EEPROM Error, press Enter to continue” : Signifies that the display board is having problems communicating with its memories.

37. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.5 3.1.3.3. LCD Inverter This device powers the LCD Display lamps. It re ceives DC power supplies (12 Vdc supply and 3.3 Vdc enable signal) from the CPU Board, and genera tes the AC voltage (380 Vac) needed to power the LCD. 3.1.3.4. Touch screen interface board This is the board that controls the 4-wire resis tive Touch Screen and interf aces the Touch Screen to the CPU Board. 3.1.3.5. AUX input board It is the circuit Board which allows audio and vi deo external sources to be displayed on the LCD base band. The board manages also the functions of the CSafe Board, detailed in the following pages, and provides 3 RC connectors and the RJ45 connector for the CSafe communication. 3.1.3.6. iPod docking station It is the device that allows to plug & store iPod models, in a safe docking station and to control it from the ACTIVE Wellness TV interface. With the docking station, developed for the full compatibility with iPod, it is possible to power, recharge and fully control it from the touch screen of the machine. In the following table, all the compatible iPod models: iPod 1st gen. iPod 5st gen. iPod Classic iPod mini iPod Nano iPod Nano:3G+4G iPod Touch: 1G+2G iPhone 3.1.3.7. Headphone jack The machine display has one jack for connecting headphones. The jack is connected on a stereo output of the CPU Board. 3.1.4. CS AFE BOARD This board makes available a communication port, on 1 externally accessible connector, which can be used for interfacing compatible CSafe devices su ch as the CardioTheater readers. This connector is situated on the back of the display. On Wellness TV models these functions are carried out by the AUX Input Board. These connectors can also be interfaced, using a sp ecial cable, to an external PC for programming the FLASH EEPROM.

155. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.3 9.1.4. P AUSE TIME It is possible to set a maximum pause time for each exercise, ranging from 10 to 999 seconds. To change the setting, when the display shows the currently selected maximum time: PAUSE TIME xxx Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 120. 9.1.5. C OOLDOWN TIME It is possible to set the cooldown time for each ex ercise, ranging from 5 to 180 seconds. To change the setting, when the display shows the currently selected maximum time: COOLDOWN TIME xxx Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 60. If you are exercising with a TGS key, the c ooldown will be stopped if you extract the key. 9.1.6. D EFAULT AGE It is possible to set the default age for a generi c user, ranging from 10 to 99 years. To change the setting, when the display shows the currently selected default age: DEFAULT AGE xx Press the ENTER key to change the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 30.

157. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.5 9.1.10. D EFAULT DISTANCE It is possible to set the default distance for an exercise session, with values ranging from 1 to 999. To change the setting, when the display shows the current value: DEFAULT DISTANCE KM xxx Press the ENTER key to modify the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 10. 9.1.11. E NABLE TGS It is possible to enable or disable the use of the TGS reader. To change the selection, when the display shows the current setting: TGS : xxx Press the +/- GOAL keys to select the desired option out of those listed in the table below: TGS ENABLED <default> DISABLED Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.1.12. E NABLE KEYBOARD It is possible to disable the keyboard so that the machine can only be used with the TGS. To change the selection, when the display shows the current setting: KEYS : xxx Press the +/- GOAL keys to select the desired option out of those listed in the table below: K EYS ENABLED <default> DISABLED Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter.

162. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.10 9.2.7. E NABLE KEYBOARD It is possible to disable the keyboard so that the machine can only be used with the TGS. To change the selection, when the display shows the current setting: KEYS : xxx Press the +/- GOAL keys to select the desired option out of those listed in the table below: K EYS ENABLED <default> DISABLED Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.2.8. M ODIFIABLE TARGET HEART RATE It is possible to enable or disable modification of the target heart rate during a constant heart rate exercise. To change the selection, when the display shows the current setting: HR : xxx Press the +/- GOAL number keys to select the desired option out of those listed in the table below: HR MODIFIABLE < default> NOT MODIFIABLE Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.2.9. E NABLE CUSTOM MESSAGES It is possible to configure whether a custom me ssage is displayed when the machine is in the standby state. To change the selection, when the display shows the current setting: CUSTOM MESS. : xxx Press the +/- GOAL number keys to select the desired option out of those listed in the table below: CUSTOM MESS. YES <default> NO Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter.

185. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.33 9.5.2. O PERATING DATA This function makes it possible to access the machine usage data stored in the low kit. In addition to the machine usage data, this func tion also includes the 2 sub-functions described below: 9.5.2.1. Read from low kit To read the parameter values from the low k it memory and view them on the display, press READ FROM LOW KIT key. 9.5.2.2. Write to low kit To write the values of the currently disp layed parameters to the low kit, press WRITE TO LOW KIT key. The machine usage data on the display is updated every 10 minutes. This means that, whenever the machine is switched off, any data modified after the last memory update will be lost. To correctly display the parameter values, you need to load them from the low kit, using the “Read from low kit” function. MESSAGE ON DISPLAY DESCRIPTION Life Brake: Minutes x 10 of operation of the brake Life Kit H: Minutes x 10 of operation of the upper assembly Life Kit L: Minutes x 10 of operation of the lower assembly Tot. Km: Total km traveled KJ Total KJ during exercise By pressing the RESET key on the side of the value, it is possi ble to reset the value of the selected item. Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.5.3. E RRORS LOG This function accesses the machine’s error history log. In addition to the error history log, this function also includes the 3 sub-functions described below: 9.5.3.1. Read from low kit To read the parameter values from the low k it memory and view them on the display, press READ FROM LOW KIT key. 9.5.3.2. Reset Errors To clear the error history in both the low and high kit memory, press RESET ERRORS key.

205. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 10.3 10.2. MECHANICAL SAFETY TESTS 10.2.1. C HECKING THE ASSEMBLY OF THE TRANSMISSION AND LEVERS SYSTEMS Check the correct assembly of the: levers, foot boards and brake components. In particular, make sure that: ™ The bearings have been correctly mounted. ™ The footboard levers have been correctly mounted and aligned. Try to exercise on the machine and check the movement is smoothly and do not produce noise; ™ The drive-belt is in good condition and correctly assembled on the pulleys. That the drive-belt and pulleys do not produce any unusual noise when the user pedals, even at a high effort level. ™ The brake winding components are correctly assembled. That the pedaling action is always smooth and silent, even at high effort level. 10.2.2. C HECKING THE ASSEMBLY OF THE GUARDS Check the assembly of the machine guards, making sure that: ™ They are all in place and correctly secured so that no parts of the machine are left exposed that may cause injury to the user. 10.3. START-UP CHECK Following installation and after every technical in tervention on the machine, plug it into a power outlet, set the power switch to ON. On power-up the machine performs a self test of the upper and lower assemblies. At the end of this the machine goes into standby, awaiting a keyboard command. To check the correct operation of the machine: ™ get on the machine; ™ begin exercising; ™ check that the displayed speed varies accordingly; ™ check that the exercise resistance varies when the “+” and “-” keys and the touch sensor are pressed and the effort level change from 1 to 25; ™ put on the heart rate meter and check that the machine correctly reads the heart rate value; ™ grasp the sensors and check that the machine correctly reads the heart rate value.

31. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.19 CU263: Display power supply cable (CPU board – Digital TV Board–Patch) Patch connector Signal Colour CPU board CN20 Digital TV board J1 Fan 1 GND Yellow/Green 1 - 2 GND 12Vdc Black 2 - 2 3 GND 5Vdc Black - 2 4 sensing GND 5V Black - 4 5 n.c. - - - 6 +12Vdc Red 6 - 1 7 +5 Vdc Red - 1 8 sensing + 5V Red - 3 2.8.3. ELT CABLE ELT-16: HFU Receiver cable (Display Board – HFU Receiver) Display Board CN3 Signal Colour HFU Receiver 1 +5 Vdc power supply White 2 7 Pulse (beat to beat) Black 4 8 Gnd Green 1

15. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.3 2.3. PRODUCT CHARACTERISTICS VERSION 500 500SP 700 - 700WTV 700SP Power requirement: 100-230VAC 50/60 Hz Self-powered 100-230VAC 50/60 Hz Self-powered Energy Consumption: 100 VA Self-powered 100 VA Self-powered Consumption Stand-by (LED): 11.3 VA (110 VAC) 21.6 VA (220 VAC) Self-powered 11.3 VA (110 VAC) 21.6 VA (220 VAC) Self-powered Consumption Stand-by (WTV): 43.7 VA (110 VAC) 61.5 VA (220 VAC) Self-powered 43.7 VA (110 VAC) 61.5 VA (220 VAC) Self-powered Difficultly levels: 1 - 25 Kind of movement: Independent Footboards Speed (min / max): 33 / 310 Max user weight: 180 Kg – 397 lbs Sub Maximal Test: NO Fitness Test Fast Track Control: NO YES HR Monitoring: Telemetry Double Hand Sensor, Telemetry Maintenance: Maintenance not required, upload Serial software Goal oriented display YES Coach Calories: YES Language available: NO YES Plug & Play System: YES HR Hand Sensor monitoring: NO YES C HARACTERISTICS Total number of programs: Quick start Goals (time, distance, calorie) CPR Profiles (6) Quick start Goals (time, distance, calories) CPR Profiles (6) Custom Training Zone Weight Loss

65. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.7 6.2.1.2. LED Test The LED test checks the functioning of the display by lighting all the LEDs in the matrix. It also tests the buzzer by changing the frequency to produce a variation in the tone of the sound. There is no message displayed concerning the outco me of this test, which must therefore be checked visually. 6.2.1.3. Serial Ports Test The serial ports test checks the communications on the following interface ports: • CSafe COM test; • Low Kit COM test; • TGS COM test. Using the + and – effort level keys, select the desired test item and confirm by pressing ENTER . The test can have two outcomes: • “Test Successful, press Enter to continue”: This means that the test was completed successfully, i.e. that the communications on the selected serial port are functioning correctly. • “COMx error, press Enter to continue” : This means that the outcome of the test was negative: the message will specify COM1 in the case of the CSafe COM test, CO M2 in the case of communications with the low kit, or COM3 in the case of the TGS COM test. The “TGS COM test” done on machine not provided with the key reader gives a fail outcome. The same if the “CSafe COM test” is done on a machine which CSafe port is not plugged with the monitor plug described at paragraph: Errore. L'origine riferimento non è stata trovata. “ Errore. L'origine riferimento non è stata trovata. ”. 6.2.2. M ANUAL T EST The tests grouped under this section conduct checks on the machine’s operation in a fully automatic manner. After selecting the desired test using the + and – effort level keys, press ENTER to initiate the test and then await the result. To exit test mode, press and hold down the CLEAR key for a few seconds. 6.2.2.1. Man. Keyboard Test The manual keyboard test checks the functioning of all the keys on the keyboard. After accessing the test by pressing ENTER , the message “ Press all buttons (beep=OK) ” appears on the display. Pressing each key will produce an audible signal; if a key does not produce the beep it means it is not working properly.

192. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.40 B. To tune and memorise Analogue TV channels, proceed as follow 1. Press ANALOGUE SEARCH. In this phase, a temporary list of TV channels found, will be stored and visualized in column 1 . 2. Wait the search stops or stop it by pressing STOP SEARCH key. The channels found in the meantime can be memorised. 3. Use the keys under the list of channels in column 1 , to scroll through the pages with the channels found during the search, while use the keys under the list of numbers in column 2 , to scroll through the pages with the numbers and names associated to the channels. 4. Select the channel frequency between the ones visualized in column 1 (it will be displayed), then press the number that you want to associate it with, in column 2 . 5. An alphanumeric keypad is displaye d, to associate a name to the memorised channel. 6. Press the ENTER ( ↵ ) key: the keypad will disappear and the name will be displayed next to the number. If a channel has already been memorised under that number, the old channel will be overwritten with the new one. 7. Repeat the procedure above for each channel you want to memorise. 8. In this way the channels will remain in the memory until the equipment is switched off ( RAM memory ); to permanently memorise the changes ( in EPROM ) press SAVE IN EPROM key. 9. Exit with “HOME” key. To transfer TV channels tuning data from a machine to another one, please refer to paragraph 9.8. “ Transferring the tuning data” WARNING: If there are problems with the digital signal reception, check the aerial antenna connection.

209. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 11.3 11.3. TWICE-YEARLY MAINTENANCE OPERATIONS These operations can only be carried out by a qualified technician specifically trained by Technogym and authorized to ca rry out machine installation and adjustments, as well as special maintenance operations or repairs which require special knowledge of the machine, its operation, safety systems and working procedures. The twice-yearly maintenance operations involve checking th e functioning, wear and tension of the mechanical components so as to ensure the correct and safe operation of the machine. For the twice-yearly maintenance of the machine, proceed as follows: 11.3.1. C ARRYING OUT THE MONTHLY MAINTENANCE PROCEDURE 1. Carry out the procedure described in paragraph 11.2. “ Monthly maintenance operations”. 11.3.2. S ETTING UP THE OPERATION 1. Turn off the machine by placing the switch in position 0 (OFF). 2. Unplug the mains lead from the wall outlet. 11.3.3. C HECKING THE WORKING CONDITIONS 1. Using a multimeter, check that the machine earth node is correctly connected to earth. 11.3.4. C HECKING THE WEAR OF RUBBER PARTS 1. Check the state of wear of the rubber component s. Replace if there are evident signs of wear. 11.3.5. C HECKING THE BELTS 1. Check the state of wear of the belts, using the pulley to turn it by hand, paying special attention to the edges and the inner part. Replace if there are evident signs of wear. 2. Also check the tension of the belts. 11.3.6. C HECKING THE PLAY OF THE LEVER AND PEDAL GROUP 1. Choose a manual training session with difficulty leve l 1. Step onto the pedals and start using the machine, moving the weight of your body backward and forward, to the right and left. Check whether the lever and pedal group follows these sh ifts in body weight with an excessive amount of play. If this is the case, replace the lever or pedal group. 11.3.7. C HECKING THE DISPLAY 1. Check the operation of all the keys on the keyboard. 2. Check the operation of all the LEDs and the buzzer.

106. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.6 7.2.3. 700WTV VERSION (W ELLNESS TV) Figure 7.2-7 Carry out the operations described in paragraphs: 7.1. “ Display disassembly”. Then place the display on a work bench. It is now possible to disassem ble its circuit boards: • The LCD inverter (A) , • The CPU Board (B). And the circuit boards mounted on the rear display support: • Digital TV Board • Input AUX Board Figure 7.2-8 LCD inverter (A) : 1. Back off the 2 screws (a) with a medium Phillips screwdriver Figure 7.2-9 2. Remove the covering plate (b) of the LCD inverter. 3. Disconnect the connectors (c) [CN2 – CN3- CN5]. 4. Back off the 2 screws (d) , which fix the board to the display plate. 5. Remove the LCD inverter. Continued on following page →

197. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.45 9.8. TRANSFERRING THE TUNING DATA The TV and radio channel tuning data can be transferred from one machine to the other in 2 ways: • using a TGS key; • connecting two machines using a CSafe connection (recommended mode). NOTE: In this way the channels will remai n in the memory until the equipment is switched off (RAM memory); to permanentl y memorise the changes (in EPROM) press SAVE IN EPROM key. 9.8.1. U SING THE TGS KEY On the already tuned machine: 1. Enter the configuration menu of the channels that are to be transferred. 2. Insert the TGS key into the reader on the machine; 3. Press the “ SAVE IN TGS ” button, this will cause all the channel configuration data to be saved to the key. Up to 45 channels can be memorised in the TGS key; if there are more channels to be memorised, a message indicates the number of TGS keys required. The TGS keys must be inserted one at the time as requested by the messages, until all the channels have been memorised. 4. Exit the menu by pressing the “ HOME ” key. On the machine to be tuned: 1. Enter the configuration menu of the channels that need to be tuned. 2. Insert the TGS key to which the tuning data was saved. 3. Press the “ READ TGS ” button. 4. Save the data uploaded to the machine by pressing “ SAVE IN EEPROM ”. 5. Exit the menu by pressing the “ HOME ” key.

156. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.4 9.1.7. D EFAULT WEIGHT It is possible to set the default weight for a generic user, ranging from 10 to 99 kilograms. To change the setting, when the display shows the currently selected default weight: DEFAULT WEIGHT KG xx Press the ENTER key to change the parameter: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 70. 9.1.8. D EFAULT DURATION It is possible to set a maximum duration for the exercise session, with a value ranging from 1 to 999 minutes. To change the setting, when the display shows the current duration: DEFAULT DURATION MIN. xxx Press the ENTER key to change the parameter: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 15 minutes. 9.1.9. D EFAULT CALORIES It is possible to set the default calories for an exercise session, with a va lue ranging from 10 to 999. To change the setting, when the display shows the current value: DEFAULT CALORIES xxx Press the ENTER key to modify the value: The current parameter value starts to blink on the display; use the ↑ and ↓ keys to increase or decrease the value, or use the +/- GOAL keys to scroll through and modify the individual digits. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. The default value of this parameter is 300.

105. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.5 7.2.2. 700 AND 700SP LED V ERSION Figure -7.2-4 Carry out the operations described in paragraphs: 7.1. “ Display disassembly”. Then place the display on a work bench. It is now possible to disassem ble its circuit boards: • The Display Board (A) ; • The C-Safe Board (B) . Figure 7.2-5 Display Board (A) : 1. Disconnect connectors (a) [CN2] of the keyboard and (b) [CN8] of the CSafe board from the Display board. 2. Back off the 5 screws (c) with a medium Phillips screwdriver. 3. Remove the circuit board. Figure 7.2-6 CSafe Board (B) : 1. Disconnect connector (d) [CN8] of the C- Safe from the Display board . 2. Remove the circuit board (e) , slipping it off from the top. Use again the hot glue to fix the connectors, where necessary. To reassemble the circuit board, carry out the above steps in reverse order

57. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 5.5 5.4. INSTALLATION To correctly install the machine, proceed as follows: 1. Ensure that the specifications and requirements fo r installation have been met (see paragraph: 5.1. “ Specifications and requirements”). 2. Position the m achine as specified above, on a leve l surface that is free of vibrations and has sufficient carrying capacity for the combined weight of the machine and user. 3. Depending on the destination country, the mach ine may be shipped partially disassembled, packed inside a special carton and fixed to a palle t, or fully assembled, wrapped in clear plastic and fixed to a wooden pallet. Follow the assembly operations described in the instruction sheets supplied with the machines. Only for 500, 700 and 700WTV models. 4. Connect the mains lead to the power inlet socket on the machine. 5. Place the on/off switch in the 0 position. 6. Plug the mains lead into the wall outlet. Only for 700WTV model. 7. Connect the antenna cable to the socket. 5.5. FIRST POWER-ON After completing the installation procedure, the machine is ready for use. On the 500, 700 and 700WTV models, simply turn the on/off switch from position 0 to position 1, while on the 500SP and 700SP models it is necessary to get on the machine and start pedaling. On power-up the machine performs a self-test of the upper and lower assemblies. After completing the self-test, the machine enters the stand by state, awaiting a command from the keyboard. To check the correct operation of the machine: • get on the machine; • start exercising; • check that the displayed speed varies accordingly; • check that exercise resistance varies when the “+” and “-“ effort level keys are pressed, or the touch sensors on the 700, 700 SP and 700WTV models are pressed, and the effort level change from 1 to 25; • put on the heart rate meter and check that the machine correctly reads the heart rate value; • only for 700, 700 SP and 700WTV: grasp the sens ors and check that the machine correctly reads the heart rate value. • only for 700WTV: Carry out the procedure described in paragraph: 9.9. “ Touch screen calibration ”.

163. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.11 9.2.10. E DIT CUSTOM MESSAGES It is possible to modify the custom messages; press ENTER to invoke a submenu which displays the first custom message, then use the +/- effort level keys to move to the other messages. Press the ENTER key again to begin editing a message, or hold down the CLEAR key for a few seconds to return to the upper menu level. While ed iting a message, move the cursor using +/- GOAL , select the desired letter using the +/- effort level keys and use CLEAR to enter a blank space character. Press ENTER to save the modified message, or hold down the CLEAR key to cancel and return to the upper menu level. 9.2.11. C HANGE MESSAGGES LANGUAGES It is also possible to display the custom st andby messages in the language selected with the preceding parameter. To extend the language setti ng to the predefined custom standby messages, when the LED display is showing the current selection: CHANGE MESS. LANGUAGE Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.2.12. E NABLE MULTI - LANGUAGE MODE The machine can be configured to allow selecti on of the language at each session. To change the selection, when the display shows the current setting: LANGUAGE : xxx Press the +/- GOAL number keys to select the desired option out of those listed in the table below: L ANGUAGE FIXED <default> OPTIONAL Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. 9.2.13. R ESETTING PARAMETERS TO DEFAULT VALUES It is possible to reset the user menu parameters to their default values. To select the function, when the display shows: DEFAULT CONFIG. Press ENTER to confirm the operation, use the + or – effort level keys to move to the next or preceding parameter. If the ENTER key is pressed the LED matrix will show: CONFIRM ? press ENTER to confirm, or cancel by pressing the CLEAR key for a few seconds.

171. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.19 9.3.17. R ADIO It is possible to enable or disable the radio func tion on the machine. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. R ADIO YES <default> NO Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.18. I P OD CONNECTION OPTION It is possible to set the machine for contro lling the iPod through the display. To change the selection, select the desired option among the one s in the list, directly touching on the Touch Screen. I P OD CONNECTION OPTION DOCKING STATION <default> NOTHING Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.19. S TANDBY CHANNEL It is possible to set the channel which is displaye d on the TV, when the TV is in standby. To change the setting, press the MODIFY key and insert the value using the numeric keyboard. Press ENTER key to confirm or BACK key to back forward. Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.20. O THER LANGUAGE It is possible to set a shortcut for a second language different from the one set at “LANGUAGE” parameter, displayed in the top left hand corner of the main page. To change the selection, select the desired opti on among the ones in the list, directly touching on the Touch Screen. Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

104. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.4 7.2. DISPLAY BOARDS DISASSEMBLY 7.2.1. 500 AND 500SP V ERSION Figure 7.2-1 Carry out the operations described in paragraphs: 7.1. “ Display disassembly”. Then place the display on a work bench. It is now possible to disassem ble its circuit boards: • The Display Board (A) ; • The C-Safe Board (B) . Figure 7.2-2 Display Board (A) : 1. Disconnect connectors (a) [CN2] of the keyboard and (b) [CN8] of the CSafe board from the Display board. 2. Back off the 5 screws (c) with a medium Phillips screwdriver. 3. Remove the circuit board. Figure 7.2-3 CSafe Board (B) : 1. Disconnect connector (d) [CN8] of the C- Safe from the Display board . 2. Remove the circuit board (e) , slipping it off from the top. Use again the hot glue to fix the connectors, where necessary. To reassemble the circuit boards, carry out the above steps in reverse order.

14. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.2 In case of overseas delivery, use “S” packaging type to order equipments with European power cord or ”U” packaging type to order equipments with US style power cord For example, a possible product code would be: DA983DTAN00RDUKE which is interpreted as follows: DA9 8 3 D T AN 00 R D UK E International Standard UK English language TV model DVB-T Dark grey casing No upholsteries frame colour Anthracite Interfaced to TGS + IPod key reader display Active Wellness TV + CDA Mains powered supply with multi-voltage inlet 700 model Wave Excite 2.2. COLOUR OPTIONS The following table shows the possible combinations for ordering the line machines: CLASS model TREND model FRAME AL AN CASING G R Table 2-1

55. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 5.3 5.3. RECOMMENDED ANTENNA SIGNAL REQUIREMENT You can find below the data useful for antenna technician, in order to check if the antenna signal is suitable for Excite Wellness TV machines. THE VALUES IN THE FOLLOWING TA BLES MUST BE MEASURED DIRECTLY ON THE ANTENNA INLET CONNECTOR OF THE MACHINE. WARNING: If the machine is not connected to a terrestrial antenna—or if it is but the antenna signal line is interrupted by devices such as TV distribution units, modulators, etc... The machine will not be able to receive a usable antenna signal for radio channel tuning. RADIO FM SIGNAL: On machines with Digi tal TV receiver, it is possible only the tuning of the digital band and not the analogue one. 5.3.1. DIGITAL SIGNAL DVB-T Level Higher than -65 dBm (44 dBμV) (-16 dBmV) Quality CH B.E.R. < 10 -3 (Channel Bit Error Rate) Or C/N (Carrier to Noise ratio) Modulation type 16 QAM: > 13 dB Modulation type 64 QAM: > 23 dB ATSC Level Higher than -65 dBm (44 dBμV) (-16 dBmV) Quality CH B.E.R . < 10 -3 (Channel Bit Error Rate) or C/N (rapporto Carrier to Noise) > 23 dB ISDB-T Level Higher than -65 dBm ( 44 dBμV) (- 16 dBmV) Quality CH B.E.R . < 10 -3 (Channel Bit Error Rate) or C/N (rapporto Carrier to Noise) Modulation type 16 QAM: > 13 dB Modulation type 64 QAM: > 23 dB Regarding the quality of the signal, it’s mo re relevant the CH.B.E.R. value instead of the C/N.

83. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.25 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Switch on the machine, connect the iPod on the docking station and check that the device is correctly detected by the machine. (2) Check that the audio/video files uploaded in the iPod are visible and selectable through the WTV interface. (3) Carry out the troubleshooting procedure 6.5. “ No audio sound”. (4) To update the iPod SW you just need to connect to iTunes and it automatically upgrades to the last version. (5) Enable the iPod control as detailed at paragraph 9.3.18. “ iPod connection option” in the user m enu. (6) The CU167 cable has identical connectors on either end then it can sometimes be connected the wrong way round. Check that the connector marked with a blue sign is connected on the AUX connectors board. (7) Place the tester probes across pins 8-9 of the connector on the docking station board where the CU167 cable is connected. The measured value should be 5 Vdc. (8) As for step (7) but across pins 6-7 of the connector on the AUX connectors board where CU167 is connected. (9) As for step (7) but across pins 9/10-13 of the connector on the AUX connectors board where CU166 is connected. (10) As for step (7) but across pins 9/10-13 of the connector J9 on the Digital TV board. (11) Place the tester probes across pins 3 - 7 on patch connector of CU169 cable. The measured value should be 5 Vdc. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

167. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.15 9.3.4. E NABLE TGS It is possible to enable or disa ble the use of the TGS reader. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. TGS ENABLED <default> DISABLED Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.5. K EYS It is possible to disable the keyboard so that the machine can only be used with the TGS. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. K EYS ENABLED <default> DISABLED Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.6. M AXIMUM EXCERCISE TIME It is possible to set a maximum duration for the ex ercise in minutes, with a value ranging from 1 to 9999. To change the setting, press the MODIFY key and insert the value using the numeric keyboard. Press ENTER key to confirm or BACK key to back forward. The default value of this parameter is 9999. Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.7. P AUSE TIME It is possible to set a maximum pause time for each exercise in seconds, with values ranging from 10 to 999. To change the setting, press the MODIFY key and insert the value using the numeric keyboard. Press ENTER key to confirm or BACK key to back forward. The default value of this parameter is 60. Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

30. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.18 CU223: Touch sensor / HS / HR cable (Display board/CPU – SALUTRON receiver – Touch Sensor) (Right Touch sensor (RED marked)) Display board: CN6 CPU board: CN26 Signal Colour Touch sensor Right 1 Power supply +5 Vdc White 1 2 Lever button Brown 2 4 Reference Green 4 (Left Touch sensor (WHITE marked)) Display board: CN5 CPU board: CN27 Signal Colour Touch sensor SX 1 Power supply +5 Vdc White 1 2 Lever button Brown 2 4 Reference Green 4 (HS/HR Receiver) Display board: CN4 CPU board: CN19 Signal Colour SALUTRON receiver HD4 1 Power supply +5 Vdc Green 2 5 Pulse (beat to beat) White 3 6 Reference Brown 1 CPU board CN21 Signal Colour CPU board CN19 7 GND Black 4 CU224: Hand Sensor cable (Receiver HS/HR– Hand Sensor) Sensors receiver HD3&2 Signal Colour DX 1 DX 2 SX 1 SX 2 1 Right sensor signal White up up - - 2 Sennsors signal reference Brown down down - - 3 GND Shield - - - - 4 Left sensor signal White - - up up 5 Sennsors signal reference Brown - - down down 6 GND Shield - - - -

36. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 3.4 3.1.3. W ELLNESS TV D ISPLAY BOARDS –D IGITAL TV (700WTV) 3.1.3.1. CPU board The board is called “Unified Board”, it is the circ uit board which incorporates the CPU, its control logic, the FLASH EPROM containing the operating program of the machine. It is the circuit board which acts as the interc onnection hub for all the components of the display and serves as the point of connection with the digital TV Board and the Brake Board. The main functions of the board are: ¾ Manages and process the signal from: ƒ LCD; ƒ Inverter for LCD; ƒ Touch screen; ƒ Headphone jack; ƒ AUX input Board; ƒ HS/HR receiver; ƒ Touch sensors; ƒ TGS reader (if present); ƒ iPod docking station (if present). ¾ Distributes the voltages received from the Brake Board to the display; ¾ Exchanges, via the RS-485 serial link to the Brake Board, the commands for controlling the brake; ¾ Manages the display of images on the LCD. The board includes the following indicator LED: LED name Colour Description D41 green if ON the +12 Vdc supply from the Brake Board correctly reaches the CPU board. and a faston: Nome Descrizione J2 denotes a ground node on the circuit board. 3.1.3.2. Digital TV board It’s the circuit board which contains the decode r and all the components needed to receive and manage the aerial antenna signal. Directly to this board it is connected the ante nna cable. Here it’s signal is amplified, divided between the video and audio signal, codified by the decoder and managed by the tuner which allows to tune the TV and radio channels. Due to its positioning on the rear display support, ju st over the AUX input board, it is also used as a “bridge” for the signals between AUX input boa rd and iPod docking station, and CPU board.

124. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.24 7.12. FOOTBOARDS LEVER DISASSEMBLY Valid for the following Serial Number (S.N.): ƒ D4963L : all S.N up to D4963L08000032 ƒ D4973E : all S.N. ƒ D4973L : all S.N. ƒ D4974L : all S.N. ƒ D4983D : all S.N. up to D4983D08000371 ƒ D4983E : all S.N. ƒ D4983I : all S.N. up to D4983I08000571 ƒ D4983L : all S.N. up to D4983L08000637 ƒ D4984L : all S.N. up to D4984L08000681 Figure 7.12-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”. 1. Back off one of the nuts (a) ( it depends from which of the lever has to be disassembled ) using a 17m m wrench, to disconnect the tie rod of the lever from the frame. 2. Back off one of the screws (b) ( it depends from which of the lever has to be disassembled ) using a 6mm hexagonal wrench and a 17mm wrench to lock down the nut on the opposite side, to disconnect the lever from the rear shock absorber. Remember to replace every spacer on the screws (b), in the same position. Continued on following page →

127. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 7.27 7.13. FOOTBOARDS LEVER DISASSEMBLY (LAST VERSION) Valid for the following Serial Number (S.N.): ƒ D4963L : From D4963L08000033 up to all S.N. ƒ D4983D : From D4983D08000372 up to all S.N. ƒ D4983I : From D4983I08000572 up to all S.N. ƒ D4983L : From D4983L08000638 up to all S.N. ƒ D4984L : From D4984L08000682 up to all S.N. ƒ DA : all S.N. Figure 7.13-1 Carry out the operations described in paragraphs: 7.7. “ Disassembling the guards”. On the lever that you want to remove: 1. Lower the footboard so that the cam which is wrapped the strap, at the position indicated in figure 2. Lock the cam inserting a wrench behind the clamping strap, centring a hole in the frame behind the cam. Figure 7.13-2 3. Back off the nut (a) (it depends from which of the lever has to be disassembled) with a 17mm wrench, to disconnect the tie rod of the lever from the frame. 4. Back off the 2 screws (b) (it depends from which of the lever has to be disassembled) , for disconnect the lever from the rear shock absorber, with a 6mm hexagonal wrench and a 17mm wrench to lock down the nut on the opposite side Continued on following page →

212. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 12.2 12.2. REQUIRED TOOLS The following tools are required for carrying out the various disassembly, adjustment and maintenance action on the machine: • Small Phillips screwdriver; • Medium Phillips screwdriver; • Big Phillips screwdriver; • 7mm wrench; • 10mm wrench; • 13mm wrench; • 17mm wrench; • 19mm wrench; • 3mm hexagonal wrench; • 4mm hexagonal wrench; • 5mm hexagonal wrench; • 6mm hexagonal wrench; • 8mm hexagonal wrench; • Socket wrench; • Snap ring pliers; You can order a complete set of hexagonal w renches consisting of 7 pieces: 2, 2.5, 3, 4, 5, 6 and 8 mm. The code to be used is R0003677AA. • PC equipped with Service Excite Loader • Serial communication cables for Excite Loader (cod. R0002534AB ); • Excite Test box (cod. H0003180AA-UK ). • Clean Well bottle (cod. 0V000356AA ).

169. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Page 9.17 9.3.10. M ODIFIABLE TARGET HEART RATE It is possible to enable or disable modification of the target heart rate during a constant heart rate exercise. To change the selection, select the de sired option among the ones in the list, directly touching on the Touch Screen. HR MODIFIABLE < default> NOT MODIFIABLE Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.11. S TANDBY It is possible to enable or disable the TV scr een during the standby mode. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. S TANDBY TV ON <default> TV OFF Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.12. L ANGUAGE The machine can be configured to allow selecti on of the language at each session. To change the selection, select the desired option among the one s in the list, directly touching on the Touch Screen. L ANGUAGE FIXED <default> OPTIONAL Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.13. D EFAULT CONFIG It is possible to reset the user menu parameters to their default values. To select the function, press on “ DEFAULT CONFIG ” key. Press HOME to confirm and save, FORWARD or BACK to scroll the pages. 9.3.14. F ORMAT P&P This function formats a TGS key for Plug&Play mode operation. To select the function, press “ FORMAT P&P ” key. Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

22. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.10 2.7.3. 700 W ELLNESS TV MODEL – D IGITAL TV 2.7.3.1. Powered version (700WTV) POWER ENTRY MODULE DISPLAY LCD CPU BOARD C N 3 0 C N 2 2 INVERTER C N 3 C N 2 C N 1 C N 5 C N 3 C N 2 0 CONNECTORS BOARD CU158 CONNECTORS PANEL Antenna inlet HEADPHONE JACK J 3 L R C-SAFE V C N 2 5 CU160 TOUCH SCREEN C N 2 8 A C N 1 CU146 F S 1 i POD DOCKI NG STATION CU167 DUAL TGS READER C N 1 Patch Conn. CU132 C N 1 CBQ-32 C N 8 DIGITAL TV BOARD J 8 J 7 Patch conn. 1 J 1 tuner CU169 J 9 CU166 CU124 J 1 0 CU164 C N 1 9 C N 2 1 C N 2 7 C N 2 6 BRAKE BRAKE BOARD C N 4 C N 3 C N 1 C N 2 SPEED SENSOR Patch Conn. NTC Patch Conn. Patch Conn. 3 CU71 Patch Conn. 2 CU69 CU67 CU63 HS/ HR RECEI VER BOARD SALUTRON 8500 H D 4 H D 3 & 2 L LOWER SENSOR R UPPER SENSOR L UPPER SENSOR R LOWER SENSOR RI GHT TOUCH SENSOR LEFT TOUCH SENSOR H D 1 CU223 CU224 Patch Conn. CU222 CU62 CU130 VAC CB-1 Ground

67. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.9 2 Chack t he cabl e that connect the Low Kit wi th Hi gh Ki t. YES NO Is the AC voltage at the i nput of the brake board correct? NO YES Repl ace CU130 cabl e NO Repl ace the power ent ry modul e YES Are the DC voltages at the output of the B arke board correct? NO Repl ace the brake board 4 A 3 I s t he A C vol tage at the out put of t he power ent ry modul e correct? Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the LEDs 1 and 2 ( green and yellow ) , of the Display Board, are correctly lit on. (2) Place the tester probes across pins 3 and 1 of CN4 connectors on the Brake Board The measured value should be approximately 220 VAC or 110 VAC depending on the mains voltage. (3) Slightly lift up the fast-on on the machine power entry module. Place the tester probes across the live and neutral pins on the same connector . The measured value should be approximately 220 VAC or 110 VAC depending on the mains voltage. (4) Using a tester, check that all the output voltages on connector CN1 of the Brake board. The measured value should be: • +12 Vdc between pins 6 - 2 ; • +5 Vdc between pins 7 - 3 . (5) Check the continuity of the signal through CU67 and CU62 cables, which connect the High Kit with Low Kit. Check also they are corr ectly connected and in a good state of wear, replace if necessary. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

69. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.11 B Is the RPM signal and the DC voltage at the input to the brake board correct? NO 5 Replace the Stator YES Replace the Brake board Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below. To speed up the troubleshooting procedure, check the state of the power indicator LEDs on the various circuit boards. (1) Check if the machine stays on for 30 seconds after having stopped pedalling. If the machine switches off in few seconds, check if the fuse on the CU110 cable is blown. Than check the battery charge, if it isn’t about 12Vdc, recharge the battery for 8 hour with an external power pack, without using the machine. (2) Check the LEDs 1 and 2 ( green and yellow ), of the Display Board, are correctly lit on. (3) Check if the LEDs 1 and 2 ( green and yellow ) of the Brake Board, are correctly lighting on, as described in paragraph: 3.1.7. “ Brake board”. (4) Using a tester, check that all the output voltages on connector CN1 of the Brake board. The measured value should be: • +12 Vdc between pins 6 - 2 ; • +5 Vdc between pins 7 - 3 . (5) Using a tester, check the voltage on connector CN3 of the Brake board. The measured value should be 16-19 Vdc, between pins 1 e 2 , nearly at 50 RPM. Use a tester, to estimate the RPM signal on the CN3 connector of the Brake board. The measured value should be approximately 30 Vac between pin 3 and a ground point. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version.

73. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 6.15 Follow the procedure step by step to correctly diagnose the problem. Take particular care with the checks highlighted by circled numbers, which are described in detail below: (1) Check the LED D41 ( green ) of the display board, is correctly lit on. (2) Start exercising in “Quick-Start” mode and check if the resistance change and a beep sound is being produced when you click on the touch sensor buttons. (3) Place the tester probes across pins 3 and 1 of CN4 connectors on the Brake board The measured value should be approximately 220 VAC or 110 VAC depending on the mains voltage. (4) Slightly lift up the fastons on the machine power entry module. Place the tester probes across the live and neutral pins on the same connector . The measured value should be approximately 220 VAC or 110 VAC depending on the mains voltage. (5) Using a tester, check that all the output voltages on connector CN1 of the Brake board. The measured value should be: • +12 Vdc between pins 6 - 2 ; • +5 Vdc between pins 7 - 3 . (6) As for step ( 5 ) but on patch connectors 1 and 3 of CU67 and CU62 cables. (7) Place the tester probes across pins 1 and 2 of J1 connectors on the Digital TV board. The measured value should be +5Vdc. (8) Place the tester probes across pins 2 and 6 of CN20 connectors on the CPU board. The measured value should be +12Vdc. If you replace Display board/Brake board, check that its SW version is updated, otherwise install the last version. The TV and RADIO channels is located in the Digital TV in the CPU Board and must necessarily be present. This means that when even one of the two boards will be replaced, should be re-stored channels thro ugh search or transferring from another machine via TGS key or cable transfer.

6. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.2 4. ACCESSORIES .................................................................................................................... ................................... 4.1 4.1. C ARDIO THEATER CONNECTION .......................................................................................................................... 4.1 4.2. PC LINK FOR PROGRAMMING .............................................................................................................................. 4.2 4.3. C ABLE FOR EXCHANGING TV CHANNEL TUNING DATA BETWEEN TWO MACHINES .............................................. 4.3 4.4. M ONITOR PLUG FOR CS AFE PORT ....................................................................................................................... 4.4 4.5. W ELLNESS TV UPGRADE KIT .............................................................................................................................. 4.5 5. INSTALLATION INSTRUCTIONS...................................................................................................... ................ 5.1 5.1. S PECIFICATIONS AND REQUIREMENTS ................................................................................................................ 5.1 5.2. M OVING THE MACHINE ............................................................................................................................... ........ 5.2 5.3. R ECOMMENDED ANTENNA SIGNAL REQUIREMENT .............................................................................................. 5.3 5.3.1. DIGITAL SIGNAL ............................................................................................................................ 5.3 5.3.2. ANALOGUE SIGNAL................................................................................................................ ....... 5.4 5.4. I NSTALLATION ............................................................................................................................... ..................... 5.5 5.5. F IRST POWER - ON ............................................................................................................................... ................. 5.5 6. TROUBLESHOOT ING .......................................................................................................................................... 6.1 6.1. T ROUBLESHOOTING SERVICE MENU : AC TIVE W ELLNESS TV MODELS ............................................................... 6.2 6.1.1. I2C Devi ce Test ................................................................................................................ ................ 6.3 6.1.2. CSafe CO M test ................................................................................................................. ............... 6.3 6.1.3. Low Kit CO M Test ............................................................................................................... ............. 6.3 6.1.4. TGS COM Test................................................................................................................... ............... 6.4 6.1.5. DVT Board TEST.............................................................................................................................. 6.4 6.2. S ERVICE TROUBLESHOOTING MENU : MODELLI LED ........................................................................................... 6.5 6.2.1. Automatic Test ................................................................................................................. ................. 6.6 6.2.1.1. I2C Devices Test............................................................................................................... ................................................ 6.6 6.2.1.2. LED Test ....................................................................................................................... .................................................... 6.7 6.2.1.3. Serial Ports Te st .............................................................................................................. .................................................. 6.7 6.2.2. Manual Test ...................................................................................................................................... 6.7 6.2.2.1. Man. Keyboard Test............................................................................................................. ............................................. 6.7 6.3. T HE DISPLAY FAILS TO ILLUMINATE ................................................................................................................... 6.8 6.3.1. 500 and 700 Models ............................................................................................................. ............ 6.8 6.3.2. 500SP and 700SP Models .............................................................................................................. 6.10 6.3.3. 700WTV Wellness TV models ...................................................................................................... ... 6.12 6.4. T HE TOUCH SCREEN DOES NOT WORK / IT ’ S NOT CALIBRATED .......................................................................... 6.16 6.5. N O AUDIO SOUND ............................................................................................................................... .............. 6.17 6.6. N O TV PICTURE ............................................................................................................................... ................. 6.18 6.7. T HE RADIO DOES NOT PLAY .............................................................................................................................. 6.21 6.8. T HE I P OD DOES NOT WORK ............................................................................................................................... 6.23 6.9. “THE EQUIPMENT IS BLOCKED (COM)” MESSAGE ON DISPLAY .............................................................. 6.26 6.10. T HERE IS NO RESISTANCE ............................................................................................................................... .. 6.27 6.11. T HE RESISTANCE IS INCORRECT ........................................................................................................................ 6.29 6.12. T HE SPEED SIGNAL IS INCORRECT ..................................................................................................................... 6.31 6.13. T HE MACHINE DOES NOT READ THE TGS.......................................................................................................... 6.33 6.14. T HERE IS NO HEART RATE SIGNAL ..................................................................................................................... 6.35 6.14.1. SALUTRON teleme tric r eceiver................................................................................................... ... 6.35 6.14.2. Hand Sensor .................................................................................................................... ............... 6.37 6.15. T HE TELEMETRIC HEART RATE SIGNAL IS INCORRECT ....................................................................................... 6.39 7. DISASSEMBLY OF COMPONENTS...................................................................................................... ............. 7.1 7.1. D ISPLAY DISASSEMBLY ............................................................................................................................... ....... 7.1 7.1.1. LED Version 500 and 500SP...................................................................................................... ...... 7.1 7.1.2. LED Version 700 and 700SP...................................................................................................... ...... 7.2 7.1.3. 700WTV version (Wellness TV) ................................................................................................... ..... 7.3 7.2. D ISPLAY B OARDS DISASSEMBLY ........................................................................................................................ 7.4 7.2.1. 500 and 500SP Version .......................................................................................................... .......... 7.4 7.2.2. 700 and 700SP LED Version...................................................................................................... ...... 7.5 7.2.3. 700WTV version (Wellness TV) ................................................................................................... ..... 7.6 7.3. 500 AND 700 KEYBOARDS AND T OUCH SCREEN DISASSEMBLY .......................................................................... 7.10

28. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.16 CU164: Audio/Video signal cable (Digital TV board – AUX input board) Digital TV board J10 Signal Colour AUX input board 1 GND video Black 1 2 Signal video Black 2 3 GND audio L Black 3 4 Signal audio L Black 4 5 Signal audio R Black 5 6 GND audio R Black 6 n.c. Black 7 CU166: CSafe – iPod – Video signals cable (Digital TV board – AUX input board) Digital TV board J9 Signal Colour AUX input board 1 Power supply +8 Vdc Black 1 2 Power supply +8 Vdc Black 2 3 Power supply +8 Vdc Black 3 6 RX – TX Black 7 7 TX – RX Black 6 8 CTS Black 8 9 Power supply +5 Vdc Black 9 10 Power supply +5 Vdc Black 10 11 GND DTV board sensing Black 11 12 GND “Play” sensing Black 12 13 GND Black 13 14 GND Black 14 15 n.c. Black - CU167: iPod signals cable (AUX input board – Docking Station) AUX input cable Signal Colour Docking Station 1 +V bus USB Black 14 2 GND bus USB Black 13 3 TX - RX Black 11 4 RX – TX Black 12 5 CTS Black 10 6 +5Vdc Black 9 7 GND Black 8 8 GND Black 7 9 GND video signal Black 6 10 Video signal Black 5 11 GND Lef audio signal Black 4 12 Left audio signal Black 3 13 Right audio signal Black 2 14 GND Right audio signal Black 1

5. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.1 Contents 1. GENERAL NOTICES................................................................................................................ ............................. 1.1 1.1. I NTRODUCTION ............................................................................................................................... .................... 1.1 1.2. R ECOMMENDATIONS ............................................................................................................................... ........... 1.1 1.3. G ENERAL RULES FOR REPAIR PROCEDURES ........................................................................................................ 1.2 2. TECHNICAL SPEC IFICATIONS ....................................................................................................... ................. 2.1 2.1. P RODUCT CODES ............................................................................................................................... .................. 2.1 2.2. C OLOUR OPTIONS ............................................................................................................................... ................ 2.2 2.3. P RODUCT CHARACTERISTICS .............................................................................................................................. 2.3 2.4. M ECHANICAL CHARACTERISTICS ....................................................................................................................... 2.4 2.5. A MBIENT SPECIFICATIONS ............................................................................................................................... ... 2.5 2.6. C ONFORMITY TO REGULATIONS .......................................................................................................................... 2.5 2.7. W IRING DIAGRAMS ............................................................................................................................... .............. 2.6 2.7.1. 500 model (ARM Board)................................................................................................................... 2.6 2.7.1.1. Powered vers ion ( 500) .......................................................................................................... ............................................ 2.6 2.7.1.2. Self-Powered version (500SP)................................................................................................... ....................................... 2.7 2.7.2. 700 model (ARM board) ................................................................................................................... 2.8 2.7.2.1. Powered vers ion ( 700) .......................................................................................................... ............................................ 2.8 2.7.2.2. Self-Powered version (700SP)................................................................................................... ....................................... 2.9 2.7.3. 700 Wellness TV mode l – Digital TV............................................................................................. . 2.10 2.7.3.1. Powered versi on (700W TV).......................................................................................................................................... 2.10 2.7.3.2. 700 and 900 models ATSC Digital Tuner .......................................................................................... ............................ 2.11 2.7.3.3. 700 and 900 models ISDB -T Digita l Tuner ........................................................................................ ........................... 2.11 2.8. W IRING 2.12 2.8.1. CBQ cables ..................................................................................................................... ................ 2.12 2.8.2. CU cables ...................................................................................................................... ................. 2.13 2.8.3. ELT cable...................................................................................................................... .................. 2.19 3. PRINCIPLES OF OPERATION........................................................................................................ .................... 3.1 3.1. B LOCK DIAGRAM ............................................................................................................................... ................. 3.1 3.1.1. LED ARM Display boards (500 and 500SP) .................................................................................... 3.2 3.1.2. Led Arm Display Boards (700 and 700SP) ...................................................................................... 3.3 3.1.3. Wellness TV Display boards –Digital TV (700WTV) ....................................................................... 3.4 3.1.3.1. CPU board...................................................................................................................... ................................................... 3.4 3.1.3.2. Digital TV board ............................................................................................................... ................................................ 3.4 3.1.3.3. LCD Inverter ................................................................................................................... .................................................. 3.5 3.1.3.4. Touch screen interface board................................................................................................... ......................................... 3.5 3.1.3.5. AUX input board ................................................................................................................ .............................................. 3.5 3.1.3.6. iPod docking station ........................................................................................................... .............................................. 3.5 3.1.3.7. Headphone jack................................................................................................................. ................................................ 3.5 3.1.4. CSafe board ...................................................................................................................................... 3.5 3.1.5. Dual TGS reader .............................................................................................................................. 3.6 3.1.6. Cardio recei ver................................................................................................................ ................. 3.6 3.1.7. Brake board ...................................................................................................................................... 3.6 3.1.8. Brake................................................................................................................................................. 3.7 3.1.9. Speed sensor ..................................................................................................................................... 3.7 3.1.10. NTC................................................................................................................................................... 3.7 3.1.11. Power entry module............................................................................................................. ............. 3.7 3.1.12. Alternator ..................................................................................................................... .................... 3.8 3.1.13. Battery ........................................................................................................................ ...................... 3.8 3.1.14. External power supply input............................................................................................................. 3.8 3.2. B RAKE CONTROL ............................................................................................................................... ................. 3.9 3.2.1. Mechanics ...................................................................................................................... ................... 3.9 3.2.2. Controls ....................................................................................................................... ..................... 3.9 3.2.3. The signals involved ........................................................................................................... ............ 3.11

13. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.1 2. TECHNICAL SPECIFICATIONS 2.1. PRODUCT CODES The machine codes take into account all the possibl e variants and options available for the products. The machine code, which does not include the SN, consists of 16 alphanumeric characters arranged as follows: Characters Description Key to values 1,2,3 Machine type DA9 = Cardio Wave Excite 4 Product version 6 = 500 8 = 700 5 Type of power supply 3 = multi-voltage (110-220) 4 = self-powered 6 Type of Display L = LED Display D = Active W-TV + Digital TV 7 Integrated accessories N = none T = TGS I = iPod A = TGS + iPod 8, 9 Colour of the frame AL = Silver (Class) AN = Anthracite (Trend) 10, 11 Colour of puddings 00 = none 12 Guards colour 0 = none G = Flint grey (Class) R = Dark grey (Trend) 13 Type of TV model 0 = none D = DVB-T A = ATSC I = ISDB-T 14,15 Language 00 = WTV models BR = Portuguese CN = Chinese DA = Danish DE = German ES = Spanish FR = French IT = Italian JP = Japanese NL = Dutch RU = Russian TR = Turkish UK = British English US = American English 16 Type of packaging I = Italy E = International Standard S = Overseas International U = Overseas US / JP

9. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.5 9.5.3.2. Reset Errors................................................................................................................... .................................................. 9.33 9.5.3.3. COM.Fault ...................................................................................................................... ................................................ 9.34 9.5.4. SW version devices ............................................................................................................. ............ 9.35 9.5.5. Standard settings ............................................................................................................................ 9.35 9.5.6. TV Standard.................................................................................................................................... 9.36 9.6. TV MENU CONFIGURATION FOR 700WTV MODELS .......................................................................................... 9.37 9.6.1. Tuning TV channels ........................................................................................................................ 9.37 9.6.2. Wellness TV adjustments ........................................................................................................ ........ 9.41 9.7. R ADIO MENU CONFIGURATION FOR 700WTV MODELS ..................................................................................... 9.42 9.7.1. Tuning radio channels .................................................................................................................... 9.42 9.8. T RANSFERRING THE TUNING DATA ................................................................................................................... 9.45 9.8.1. Using the TGS key .............................................................................................................. ............ 9.45 9.8.2. Connecting two machines using a C Safe connection ( Method recommended) .............................. 9.46 9.9. T OUCH SCREEN CALIBRATION .......................................................................................................................... 9.47 10. FUNCTIONAL TEST MD MODELS...................................................................................................... ............ 10.1 10.1. E LECTRICAL SAFETY TEST ............................................................................................................................... . 10.1 10.2. M ECHANICAL SAFETY TESTS ............................................................................................................................ 10.3 10.2.1. Checking the assembly of the transmission and l evers systems...................................................... 10.3 10.2.2. Checking the assembly of the guards............................................................................................ .. 10.3 10.3. S TART - UP CHECK ............................................................................................................................... ............... 10.3 10.4. L IST OF CRITICAL SPARE PARTS ........................................................................................................................ 10.4 11. SCHEDULED MAINTENANCE .......................................................................................................... ............... 11.1 11.1. D AILY MAINTENANCE OPERATIONS .................................................................................................................. 11.1 11.1.1. Setting up the operation....................................................................................................... ........... 11.1 11.1.2. External cle aning operations.......................................................................................................... 11.1 11.2. M ONTHLY MAINTENANCE OPERATIONS ............................................................................................................ 11.2 11.2.1. Cleaning operations ............................................................................................................ ........... 11.2 11.2.2. Checking the state of wear of the pedal lever belt .......................................................................... 11.2 11.2.3. Checking the amount of pl ay on the ball joints .............................................................................. 11.2 11.2.4. Checking the operation of th e cardiotest er r eceiver....................................................................... 11.2 11.2.5. Checking the operation of the hand sensor receiver ...................................................................... 11.2 11.3. T WICE - YEARLY MAINTENANCE OPERATIONS .................................................................................................... 11.3 11.3.1. Carrying out the monthly maintenance procedure ......................................................................... 11.3 11.3.2. Setting up the operation....................................................................................................... ........... 11.3 11.3.3. Checking the working conditions................................................................................................ .... 11.3 11.3.4. Checking the wear of rubber parts .............................................................................................. ... 11.3 11.3.5. Checking th e belts............................................................................................................. .............. 11.3 11.3.6. Checking the play of th e lever and pedal group ............................................................................. 11.3 11.3.7. Checking the display....................................................................................................................... 11.3 11.3.8. Checking the wiring and connections............................................................................................ . 11.4 12. APPENDIX............................................................................................................................................................. 12.1 12.1. U PDATING THE SW .......................................................................................................................................... 12.1 12.2. R EQUIRED TOOLS ............................................................................................................................... .............. 12.2

7. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.3 7.3.1. 500 and 500SP models ........................................................................................................... ........ 7.10 7.3.2. 700 and 700SP LED Version...................................................................................................... .... 7.11 7.3.3. 700WTV version (Wellness TV) ................................................................................................... ... 7.12 7.4. C ARDIO /H AND SENSOR RECEIVER DISASSEMBLY ............................................................................................. 7.13 7.5. F IXED HANDGRIPS DISASSEMBLY ...................................................................................................................... 7.15 7.6. D ISASSEMBLING THE SENSOR ........................................................................................................................... 7.16 7.7. D ISASSEMBLING THE GUARDS .......................................................................................................................... 7.17 7.8. D ISASSEMBLING THE UPPER COLUMN ............................................................................................................... 7.19 7.9. B RAKE BOX DISASSEMBLY ............................................................................................................................... 7.20 7.10. D ISASSEMBLING THE FOOTBOARDS .................................................................................................................. 7.21 7.11. FOOTBOARD LEVER B ELT DISASSEMBLY ........................................................................................................... 7.22 7.12. F OOTBOARDS LEVER DISASSEMBLY .................................................................................................................. 7.24 7.13. F OOTBOARDS LEVER DISASSEMBLY ( LAST VERSION) .................................................................................... 7.27 7.14. D ISASSEMBLING THE LEVERS TENSIONING SPRING ........................................................................................... 7.30 7.15. D ISASSEMBLING THE BRAKE WINDING .............................................................................................................. 7.32 7.16. D ISASSEMBLING THE SECONDARY SHAFT ASSEMBLY ....................................................................................... 7.33 7.16.1. 700 Powered and 700WTV models................................................................................................. 7.34 7.16.2. 700SP Self-Powered models ...................................................................................................... ..... 7.35 7.17. D ISASSEMBLING THE PRIMARY SHAFT ASSEMBLY ............................................................................................ 7.37 7.18. D ISASSEMBLING THE CONNECTION BELT B ETWEEN PRIMARY AN D SECONDARY SHAFT .................................... 7.39 7.19. S PEED SENSOR DISASSEMBLY ........................................................................................................................... 7.40 7.20. D ISASSEMBLING THE POWER ENTRY MODULE ................................................................................................... 7.41 7.21. D ISASSEMBLING THE PLATFORMS ..................................................................................................................... 7.42 7.22. S MONTAGGIO BATTERIA ............................................................................................................................... .... 7.43 8. ADJUSTMENTS.................................................................................................................... .................................. 8.1 8.1. B ELT TENSION ............................................................................................................................... ..................... 8.1 8.2. S PEED SENSOR POSITION ............................................................................................................................... ...... 8.2 8.3. B RAKE WINDING POSITION ............................................................................................................................... .. 8.3 8.4. A LIGN THE BELT CONNECTING THE PRIMARY AND SECONDARY SHAFTS ............................................................. 8.4 8.5. T HE DISTANCE BETWEEN THE PEDALS ................................................................................................................ 8.5 8.6. T IE ROD LENGTH ............................................................................................................................... .................. 8.6 8.7. T HE MACHINE IS NOT FLAT ............................................................................................................................... .. 8.8 9. MACHINE CONFIGURATION .......................................................................................................... .................. 9.1 9.1. U SER MENU CONFIGURATION FOR 500 MODELS .................................................................................................. 9.1 9.1.1. Language .......................................................................................................................................... 9.2 9.1.2. Units of measurement ........................................................................................................... ............ 9.2 9.1.3. Maximum exerci se time .......................................................................................................... .......... 9.2 9.1.4. Pause time ..................................................................................................................... ................... 9.3 9.1.5. Cooldown time .................................................................................................................. ................ 9.3 9.1.6. Default age .................................................................................................................... ................... 9.3 9.1.7. Default weight................................................................................................................. .................. 9.4 9.1.8. Default duration ............................................................................................................... ................ 9.4 9.1.9. Default ca lories ............................................................................................................... ................. 9.4 9.1.10. Default di stance ................................................................................................................................ 9.5 9.1.11. Enable TGS....................................................................................................................................... 9.5 9.1.12. Enable keyboard ................................................................................................................ ............... 9.5 9.1.13. Modifiable target frequencies.................................................................................................. ......... 9.6 9.1.14. Resetting parameters to default values ......................................................................................... .... 9.6 9.1.15. Format P&P key ................................................................................................................. .............. 9.6 9.1.16. SN ..................................................................................................................................................... 9.6 9.2. U SER MENU CONFIGURATION FOR 700 MODELS .................................................................................................. 9.7 9.2.1. Language .......................................................................................................................................... 9.8 9.2.2. Distance ....................................................................................................................... ..................... 9.8 9.2.3. Maximum excerci se time......................................................................................................... .......... 9.8 9.2.4. Pause time ..................................................................................................................... ................... 9.9 9.2.5. Cooldown time .................................................................................................................. ................ 9.9 9.2.6. Enable TGS....................................................................................................................................... 9.9

27. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 2.15 CU130: High voltage cable (Power entry module – Brake board) Power entry module Signal Colour Brake board CN4 F Line White 1 N Neutral Black 3 T Earth Green 5 CU132: TGS Cable (Patch conn. – Dual TGS reader) Patch conn. Signal Colour Dual TGS reader CN1 1 +12 Vdc power supply Black 1 8 Rx Green 2 7 Tx Black 3 3 Gnd Black 8 CU158: AUX signals cable (CPU board –Digital TV board) CPU board CN22 Signal Colour Digital TV board J8 1 GND video signal Black 7 2 Video signal White 6 3 GND Left audio signal Black 3 4 Left audio signal White 2 5 Right audio signal White 4 6 GND right audio signal Black 5 CU160: CSafe – iPod – Video signals cable (CPU board – Digital TV board) CPU board CN25 Signal Colour Digital TV board J7 1 Power supply +8 Vdc Black 1 2 Power supply +8 Vdc Black 2 3 Power supply +8 Vdc Black 3 6 RX – TX Black 7 7 TX – RX Black 6 8 CTS Black 8 9 Power supply +5 Vdc Black 9 10 Power supply +5 Vdc Black 10 11 GND DTV board sensing Black 11 12 GND “Play” sensing Black 12 13 GND Black 13 14 GND Black 14

8. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 1.4 9.2.7. Enable keyboard ................................................................................................................ ............. 9.10 9.2.8. Modifiable target heart rate ................................................................................................... ........ 9.10 9.2.9. Enable custom messages ......................................................................................................... ....... 9.10 9.2.10. Edit custom messages ........................................................................................................... .......... 9.11 9.2.11. Change messagges languages ........................................................................................................ 9.11 9.2.12. Enable multi-language mode.......................................................................................................... 9.11 9.2.13. Resetting parameters to default values ......................................................................................... .. 9.11 9.2.14. Format P&P ................................................................................................................................... 9.12 9.2.15. SN ................................................................................................................................................... 9.12 9.3. U SER MENU CONFIGURATION FOR 700 WTV MODELS ...................................................................................... 9.13 9.3.1. SN ................................................................................................................................................... 9.14 9.3.2. Language ........................................................................................................................................ 9.14 9.3.3. Measure .......................................................................................................................................... 9.14 9.3.4. Enable TGS..................................................................................................................................... 9.15 9.3.5. Keys ........................................................................................................................... ..................... 9.15 9.3.6. Maximum excerci se time......................................................................................................... ........ 9.15 9.3.7. Pause time ..................................................................................................................... ................. 9.15 9.3.8. Cooldown time .................................................................................................................. .............. 9.16 9.3.9. Top exercise programs for you shortcut ......................................................................................... 9.16 9.3.10. Modifiable target heart rate ................................................................................................... ........ 9.17 9.3.11. Standby ........................................................................................................................................... 9.17 9.3.12. Language ........................................................................................................................................ 9.17 9.3.13. Default config ................................................................................................................. ................ 9.17 9.3.14. Format P&P ................................................................................................................................... 9.17 9.3.15. Screen saver minutes ........................................................................................................... ........... 9.18 9.3.16. Display in the workout......................................................................................................... ........... 9.18 9.3.17. Radio............................................................................................................................................... 9.19 9.3.18. iPod connection option ......................................................................................................... .......... 9.19 9.3.19. Standby channel.............................................................................................................................. 9.19 9.3.20. Other language ............................................................................................................................... 9.19 9.4. S ERVICE MENU CONFIGURATION FOR 500 AND 700 LED MODELS .................................................................... 9.20 9.4.1. Low kit par ameter.............................................................................................................. ............. 9.22 9.4.1.1. Read from low kit .............................................................................................................. ............................................. 9.22 9.4.1.2. Write to low kit ............................................................................................................... ................................................ 9.22 9.4.1.3. Default Setting ................................................................................................................ ................................................ 9.23 9.4.1.4. Table of configuration parameters.............................................................................................. .................................... 9.23 9.4.2. Operating data................................................................................................................................ 9.24 9.4.2.1. Read from low kit .............................................................................................................. ............................................. 9.24 9.4.2.2. Write to low kit ............................................................................................................... ................................................ 9.25 9.4.2.3. Machine us age data............................................................................................................. ............................................ 9.25 9.4.3. Errors log ..................................................................................................................... .................. 9.26 9.4.3.1. Read from low kit .............................................................................................................. ............................................. 9.26 9.4.3.2. Reset Errors................................................................................................................... .................................................. 9.26 9.4.3.3. COM.Fault ...................................................................................................................... ................................................ 9.27 9.4.3.4. View Errors ..................................................................................................................................................................... 9.27 9.4.4. Standard settings ............................................................................................................................ 9.28 9.4.5. Low kit menu................................................................................................................................... 9.28 9.4.5.1. Low kit version ................................................................................................................ ............................................... 9.28 9.4.5.2. Low Kit fa ult code ............................................................................................................. ............................................. 9.29 9.4.6. High kit version ............................................................................................................... ............... 9.29 9.4.7. BOOT version ................................................................................................................... .............. 9.29 9.4.8. Key Reader Version ............................................................................................................. ........... 9.29 9.5. S ERVICE MENU CONFIGURATION 700 WTV MODELS ........................................................................................ 9.30 9.5.1. Low kit par ameter.............................................................................................................. ............. 9.31 9.5.1.1. Read from low kit .............................................................................................................. ............................................. 9.31 9.5.1.2. Write to low kit ............................................................................................................... ................................................ 9.31 9.5.1.3. Default Setting ................................................................................................................ ................................................ 9.31 9.5.1.4. Table of configuration parameters.............................................................................................. .................................... 9.32 9.5.2. Operating data................................................................................................................................ 9.33 9.5.2.1. Read from low kit .............................................................................................................. ............................................. 9.33 9.5.2.2. Write to low kit ............................................................................................................... ................................................ 9.33 9.5.3. Errors log ..................................................................................................................... .................. 9.33 9.5.3.1. Read from low kit .............................................................................................................. ............................................. 9.33

49. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 4.5 4.5. WELLNESS TV UPGRADE KIT There are upgrade kits available for converting Excite machines from the version with traditional LED Display to the Wellness TV Display version with ACTIVE TV interface and integrated digital TV decoder. The kit also includes all the cables and connectors required for the input of the antenna signal. The table below gives the codes of the kits, to be chosen according to the TV standard used in the installation country. WELLNESS TV UPGRADE KIT CODICE WAVE 700 DVB-T A0000405-D WAVE 700 ATSC A0000405-A WAVE 700 ISDB-T A0000405-I In the following table you can find th e list of the analogyc and digital TV standard for the different countries. COUNTRY DIGITAL TV ANALOG TV COUNTRY DIGITAL TV ANALOG TV ALBANIA DVB-T PAL B/G LUXEMBOURG DVB-T PAL B/G ANGOLA DVB-T - MALAYSIA DVB-T PAL B AUSTRALIA DVB-T PAL B/G MALTA DVB-T PAL B/G AUSTRIA DVB-T PAL B/G MAURITIUS DVB-T SECAM B AZERBAIJAN DVB-T - MEXICO ATSC NTSC M BAHAMAS ATSC NTSC M MONACO DVB-T SECAM/PAL L/G BAHRAIN DVB-T PAL B MOROCCO DVB-T SECAM B BELGIUM DVB-T PAL B/G NETHERLANDS DVB-T PAL B/G BERMUDA DVB-T NTSC M NEW ZEALAND DVB-T PAL B/G BRAZIL ATSC PAL M NIGERIA DVB-T - BULGARY DVB-T SECAM D/K NORWAY DVB-T PAL B/G CANADA ATSC NTSC M OMAN DVB-T - COLOMBIA ATSC NTSC M PHILIPPINES DVB-T NTSC M CYPRUS DVB-T PAL B POLAND DVB-T PAL D/K CZECH REPUBLIC DVB-T SECAM/PAL D/K PORTUGAL DVB-T PAL B/G DENMARK DVB-T PAL B P.R.CHINA DVB-T PAL D/K EGYPT DVB-T SECAM B QATAR DVB-T - FAROE ISLANDS DVB-T PAL B ROMANIA DVB-T PAL G FINLAND DVB-T PAL B/G RUSSIA DVB-T SECAM D/K FRANCE DVB-T SECAM E/L SAUDI ARABIA DVB-T SECAM B GERMANY DVB-T PAL B/G SERBIA DVB-T - GHANA DVB-T - SINGAPORE DVB-T PAL B GREECE DVB-T PAL B/G SLOVAKIA DVB-T - HONG KONG DVB-T PAL I SLOVENIA DVB-T - HUNGARY DVB-T PAL B/G & D/K SOUTH AFRICA DVB-T PAL I INDIA DVB-T PAL B SOUTH KOREA ATSC NTSC M INDONESIA DVB-T PAL B SPAIN DVB-T PAL B/G IRAN DVB-T SECAM H SWEDEN DVB-T PAL B/G IRELAND DVB-T PAL I SWITZERLAND DVB-T PAL B/G ISRAEL DVB-T PAL B/G SYRIA DVB-T - ITALY DVB-T PAL B/G TAIWAN DVB-T NTSC M JAPAN ISDB-T NTSC M TUNISIA DVB-T SECAM B JORDAN DVB-T PAL B TURKEY DVB-T PAL B KAZAKHSTAN DVB-T - U.S.A. ATSC NTSC M KENYA DVB-T PAL B UAE DVB-T PAL B/G LATVIA DVB-T - UNITED KINGDOM DVB-T PAL I LEBANON DVB-T - URUGUAY DVB-T PAL N

188. CARDIO WAVE EXCITE Class & Trend: Service & maintenance manual- rev.2.0 Pagina 9.36 9.5.6. TV S TANDARD This function allows to display/configure the TV Standard on the machine. To change the selection, select the desired option among the ones in the list, directly touching on the Touch Screen. NTSC M NTSC44 M PAL B/G PAL I PAL D/K SECAM D/K SECAM L SECAM L1 PAL B/H PAL M SECAM H SECAM B/G PAL N Selected as a function of the country where th e machine is installed according to the following table: COUNTRY Digital TV Analogue TV COUNTRY Digital TV Analogue TV ALBANIA DVB-T PAL B/G LUXEMBOURG DVB-T PAL B/G ANGOLA DVB-T - MALAYSIA DVB-T PAL B AUSTRALIA DVB-T PAL B/G MALTA DVB-T PAL B/G AUSTRIA DVB-T PAL B/G MAURITIUS DVB-T SECAM B AZERBAIJAN DVB-T - MEXICO ATSC NTSC M BAHAMAS ATSC NTSC M MONACO DVB-T SECAM/PAL L/G BAHRAIN DVB-T PAL B MOROCCO DVB-T SECAM B BELGIUM DVB-T PAL B/G NETHERLANDS DVB-T PAL B/G BERMUDA DVB-T NTSC M NEW ZEALAND DVB-T PAL B/G BRAZIL ATSC PAL M NIGERIA DVB-T - BULGARY DVB-T SECAM D/K NORWAY DVB-T PAL B/G CANADA ATSC NTSC M OMAN DVB-T - COLOMBIA ATSC NTSC M PHILIPPINES DVB-T NTSC M CYPRUS DVB-T PAL B POLAND DVB-T PAL D/K CZECH REPUBLIC DVB-T SECAM/PAL D/K PORTUGAL DVB-T PAL B/G DENMARK DVB-T PAL B P.R.CHINA DVB-T PAL D/K EGYPT DVB-T SECAM B QATAR DVB-T - FAROE ISLANDS DVB-T PAL B ROMANIA DVB-T PAL G FINLAND DVB-T PAL B/G RUSSIA DVB-T SECAM D/K FRANCE DVB-T SECAM E/L SAUDI ARABIA DVB-T SECAM B GERMANY DVB-T PAL B/G SERBIA DVB-T - GHANA DVB-T - SINGAPORE DVB-T PAL B GREECE DVB-T PAL B/G SLOVAKIA DVB-T - HONG KONG DVB-T PAL I SLOVENIA DVB-T - HUNGARY DVB-T PAL B/G & D/K SOUTH AFRICA DVB-T PAL I INDIA DVB-T PAL B SOUTH KOREA ATSC NTSC M INDONESIA DVB-T PAL B SPAIN DVB-T PAL B/G IRAN DVB-T SECAM H SWEDEN DVB-T PAL B/G IRELAND DVB-T PAL I SWITZERLAND DVB-T PAL B/G ISRAEL DVB-T PAL B/G SYRIA DVB-T - ITALY DVB-T PAL B/G TAIWAN DVB-T NTSC M JAPAN ISDB-T NTSC M TUNISIA DVB-T SECAM B JORDAN DVB-T PAL B TURKEY DVB-T PAL B KAZAKHSTAN DVB-T - U.S.A. ATSC NTSC M KENYA DVB-T PAL B UAE DVB-T PAL B/G LATVIA DVB-T - UNITED KINGDOM DVB-T PAL I LEBANON DVB-T - URUGUAY DVB-T PAL N LIBYA DVB-T - Press HOME to confirm and save, FORWARD or BACK to scroll the pages.

Views

  • 183 Total Views
  • 115 Website Views
  • 68 Embeded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 2

  • 8 www.fitness-trader.com
  • 3 fitness-trader.odoo.com
You can compare max 4 products.